Home › Vehicle Interior › SEAT BELT › CHILD RESTRAINT SEAT ANCHOR BRACKET

CHILD RESTRAINT SEAT ANCHOR BRACKET > REMOVAL

for Preparation Click here



1. REMOVE REAR SEAT HEADREST ASSEMBLY


2. REMOVE REAR CENTER SEAT HEADREST ASSEMBLY


3. REMOVE FRONT FLOOR COVER RH


    B301488E01
  1. Using a clip remover, remove the 2 clips <A>.

  1. Disengage the 3 clips <B>.



    B301489
  1. Disengage the 3 guides and remove the front floor cover RH.



4. REMOVE FRONT FLOOR COVER LH


    B301490E01
  1. Using a clip remover, remove the 2 clips <A>.

  1. Disengage the 3 clips <B>.



    B301491
  1. Disengage the 3 guides and remove the front floor cover LH.



5. REMOVE FRONT CENTER FLOOR COVER


    B296737
  1. Using a clip remover, remove the 3 clips.

  1. Disengage the 2 guides and remove the front center floor cover.



6. REMOVE REAR SEAT CUSHION ASSEMBLY (for Bench Type Seatback)


    B297552E01
  1. Using a clip remover, disengage the 2 clips.
    Text in Illustration 
    *a
    RH Side
    *b
    LH Side



    B296114E01
  1. Disengage the hook of the rear seat cushion assembly from the vehicle body as shown in the illustration.
    Standard Measurement 
    a
    100 mm (3.94 in.) or less

    NOTICE:
    Follow the instructions below carefully as the cushion frame can be deformed easily.


    1. Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.

    2. Repeat the step above for the other hook.

  1. Remove the rear seat cushion assembly.

    NOTICE:
    Be careful not to damage the vehicle body.



7. REMOVE REAR SEATBACK ASSEMBLY (for Bench Type Seatback)
  1. Fold down the rear seatback assembly.



    B296118
  1. Remove the 2 bolts and rear seatback assembly.

    NOTICE:
    Be careful not to damage the vehicle body.



8. REMOVE REAR SEAT CUSHION ASSEMBLY (for Separate Type Seatback)


    B297552E01
  1. Using a clip remover, disengage the 2 clips.
    Text in Illustration 
    *a
    RH Side
    *b
    LH Side



    B296114E01
  1. Disengage the hook of the rear seat cushion assembly from the vehicle body as shown in the illustration.
    Standard Measurement 
    a
    100 mm (3.94 in.) or less

    NOTICE:
    Follow the instructions below carefully as the cushion frame can be deformed easily.


    1. Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.

    2. Repeat the step above for the other hook.

  1. Remove the rear seat cushion assembly.

    NOTICE:
    Be careful not to damage the vehicle body.



9. REMOVE REAR SEATBACK ASSEMBLY RH (for Separate Type Seatback)
  1. Fold down the rear seatback assembly RH.



    B296151
  1. Remove the 2 bolts and rear seatback assembly RH.

    NOTICE:
    Be careful not to damage the vehicle body.



10. REMOVE REAR SEATBACK ASSEMBLY LH (for Separate Type Seatback)
  1. Fold down the rear seatback assembly LH.



    B296146
  1. Remove the 2 bolts and rear seatback assembly LH.

    NOTICE:
    Be careful not to damage the vehicle body.



11. REMOVE REAR DOOR SCUFF PLATE LH


    B300785
  1. Disengage the 5 claws and guide and remove the rear door scuff plate LH.



12. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
  1. Remove the rear door opening trim weatherstrip LH.



13. REMOVE REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure as for the LH side.



14. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure as for the LH side.



15. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)
  1. Remove the package tray trim panel assembly.



16. REMOVE REAR FLOOR MAT ASSEMBLY
  1. Remove the rear floor mat assembly.



17. REMOVE SPARE WHEEL CUSHION
  1. Remove the 2 spare wheel cushions.



18. REMOVE REAR DECK TRIM COVER


    B300795
  1. Remove the 2 clips.

  1. Disengage the 4 claws and 2 guides, and remove the rear deck trim cover.



19. DISCONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH
  1. Remove the bolt.



    B307773
  1. Disengage the 2 claws and disconnect the floor anchor of the rear seat 3 point type outer belt assembly.



20. REMOVE REAR ABSORBER CAP LH (w/ Package Tray Trim)


    B300796
  1. Disengage the 2 claws and 2 guides, and remove the rear absorber cap LH.



21. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY (w/ Package Tray Trim)


    E286958E03
  1. Using a screwdriver with its tip wrapped with protective tape, disengage the claw.
    Text in Illustration 
    *a
    Protective Tape



    E286959
  1. Remove the No. 1 luggage compartment light assembly as shown in the illustration.

  1. Disconnect the connector and remove the No. 1 luggage compartment light assembly.



22. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH (w/o Package Tray Trim)


  1. Turn the rear seatback hinge in the direction indicated by the arrow shown in the illustration.


    B300797E01


    Text in Illustration 
    *1
    Rear Seatback Hinge
    -
    -

  1. Remove the 2 screws.

  1. Using a clip remover, remove the 5 clips.

  1. Disengage the 2 clips and guide, and remove the deck trim side panel assembly LH.



23. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH (w/ Package Tray Trim)


  1. Turn the rear seatback hinge in the direction indicated by the arrow shown in the illustration.


    B300799E01


    Text in Illustration 
    *1
    Rear Seatback Hinge
    -
    -

  1. Remove the bolt and 2 screws.

  1. Disengage the 4 claws, 4 clips and guide, and remove the deck trim side panel assembly LH.



24. DISCONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH
  1. Remove the bolt.



    B307773
  1. Disengage the 2 claws and disconnect the floor anchor of the rear seat 3 point type outer belt assembly.



25. REMOVE REAR ABSORBER CAP RH (w/ Package Tray Trim)

HINT:
Use the same procedure as for the LH side.



26. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH (w/o Package Tray Trim)

HINT:
Use the same procedure as for the LH side.



27. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH (w/ Package Tray Trim)

HINT:
Use the same procedure as for the LH side.



28. REMOVE CROSS ANCHOR BRACKET SUB-ASSEMBLY (for Bench Type Seatback)


  1. Remove the 3 bolts and cross anchor bracket sub-assembly.


    B297200



29. REMOVE CROSS ANCHOR BRACKET SUB-ASSEMBLY (for Separate Type Seatback)


  1. Remove the 3 bolts and cross anchor bracket sub-assembly.


    B297198