Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM

POWER DOOR LOCK CONTROL SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B281049E05

  1. Disconnect the MB main body ECU (multiplex network body ECU) connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connectors disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    MB-11 (GND1) - Body ground
    -
    Ground
    Always
    Below 1 Ω
    MB-30 (BECU) - Body ground
    -
    Auxiliary battery power supply
    Ignition switch off
    11 to 14 V
    MB-29 (ACC) - Body ground
    -
    ACC power supply
    Ignition switch ACC
    11 to 14 V
    MB-29 (ACC) - Body ground
    -
    ACC power supply
    Ignition switch off
    Below 1 V
    MB-32 (IG) - Body ground
    -
    Ignition switch power supply
    Ignition switch ON (IG)
    11 to 14 V
    MB-32 (IG) - Body ground
    -
    Ignition switch power supply
    Ignition switch off
    Below 1 V
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the MB main body ECU (multiplex network body ECU) connector.

  4. Measure the voltage and check for pulses according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    3B-3 (ACT-) - Body ground
    R - Body ground
    Door lock motor unlock drive output (except driver door)
    Door control switch (power window regulator master switch) or driver door key cylinder off
    Below 1 V
    3B-3 (ACT-) - Body ground
    R - Body ground
    Door lock motor unlock drive output (except driver door)
    Door control switch (power window regulator master switch) or driver door key cylinder unlocked
    11 to 14 V
    3B-1 (ACT+) - Body ground
    Y - Body ground
    Door lock motor lock drive output (all doors)
    Door control switch (power window regulator master switch) or driver door key cylinder off
    Below 1 V
    3B-1 (ACT+) - Body ground
    Y - Body ground
    Door lock motor lock drive output (all doors)
    Door control switch (power window regulator master switch) or driver door key cylinder locked
    11 to 14 V
    3B-4 (ACTD) - Body ground
    L - Body ground
    Driver door lock motor unlock drive output
    Door control switch (power window regulator master switch) or driver door key cylinder off
    Below 1 V
    3B-4 (ACTD) - Body ground
    L - Body ground
    Driver door lock motor unlock drive output
    Door control switch (power window regulator master switch) or driver door key cylinder unlocked
    11 to 14 V
    G59-19 (FRCY) - Body ground
    R - Body ground
    Front door courtesy light switch RH input
    Front door RH open
    Below 1 V
    G59-19 (FRCY) - Body ground
    R - Body ground
    Front door courtesy light switch RH input
    Front door RH closed
    Pulse generation
    3D-36 (FLCY) - Body ground
    R - Body ground
    Front door courtesy light switch LH input
    Front door LH open
    Below 1 V
    3D-36 (FLCY) - Body ground
    R - Body ground
    Front door courtesy light switch LH input
    Front door LH closed
    Pulse generation
    G59-1 (LCTY) - Body ground
    L - Body ground
    Rear door courtesy light switch LH input
    Rear door LH open
    Below 1 V
    G59-1 (LCTY) - Body ground
    L - Body ground
    Rear door courtesy light switch LH input
    Rear door LH closed
    Pulse generation
    G59-6 (RCTY) - Body ground
    G - Body ground
    Rear door courtesy light switch RH input
    Rear door RH open
    Below 1 V
    G59-6 (RCTY) - Body ground
    G - Body ground
    Rear door courtesy light switch RH input
    Rear door RH closed
    Pulse generation
    G59-9 (L1) - Body ground
    L - Body ground
    Door control switch input
    Door control switch locked
    Below 1 V
    G59-9 (L1) - Body ground
    L - Body ground
    Door control switch input
    Door control switch off
    Pulse generation
    G59-10 (UL1) - Body ground
    W - Body ground
    Door control switch input
    Door control switch unlocked
    Below 1 V
    G59-10 (UL1) - Body ground
    W - Body ground
    Door control switch input
    Door control switch off
    Pulse generation
    G59-11 (L2) - Body ground
    SB - Body ground
    Driver door key-linked lock input
    Driver door key cylinder turned to lock
    Below 1 V
    G59-11 (L2) - Body ground
    SB - Body ground
    Driver door key-linked lock input
    Driver door key cylinder off
    Pulse generation
    G59-24 (UL3) - Body ground
    G - Body ground
    Driver door key-linked unlock input
    Driver door key cylinder turned to unlock
    Below 1 V
    G59-24 (UL3) - Body ground
    G - Body ground
    Driver door key-linked unlock input
    Driver door key cylinder off
    Pulse generation
    G59-7 (LSFL) - Body ground
    L - Body ground
    Front door LH unlock detection switch input
    Front door LH unlocked
    Below 1 V
    G59-7 (LSFL) - Body ground
    L - Body ground
    Front door LH unlock detection switch input
    Front door LH locked
    Pulse generation
    G59-18 (LSFR) - Body ground
    L - Body ground
    Front door RH unlock detection switch input
    Front door RH unlocked
    Below 1 V
    G59-18 (LSFR) - Body ground
    L - Body ground
    Front door RH unlock detection switch input
    Front door RH locked
    Pulse generation
    3D-25 (LSR) - Body ground*1
    V - Body ground
    Rear door RH unlock detection switch input
    Rear door RH or LH unlocked
    Below 1 V
    3D-25 (LSR) - Body ground*1
    V - Body ground
    Rear door RH unlock detection switch input
    Rear door RH and LH locked
    Pulse generation
    3D-24 (LSR) - Body ground*1
    Y - Body ground
    Rear door LH unlock detection switch input
    Rear door LH or RH unlocked
    Below 1 V
    3D-24 (LSR) - Body ground*1
    Y - Body ground
    Rear door LH unlock detection switch input
    Rear door LH and RH locked
    Pulse generation
    3D-35 (BCTY) - Body ground
    B - Body ground
    Back door courtesy light switch input
    Back door open
    Below 1 V
    3D-35 (BCTY) - Body ground
    B - Body ground
    Back door courtesy light switch input
    Back door closed
    11 to 14 V
    3D-9 (TR+) - Body ground
    Y - Body ground
    Back door lock motor unlock drive output
    Back door opener switch (open switch) pushed
    11 to 14 V
    3D-9 (TR+) - Body ground
    Y - Body ground
    Back door lock motor unlock drive output
    Back door opener switch (open switch) not pushed
    Below 1 V
    G59-23 (BDSU) - Body ground*2
    L - Body ground
    Back door opener switch input
    Back door opener switch (open switch) pushed
    Below 1 V
    G59-23 (BDSU) - Body ground*2
    L - Body ground
    Back door opener switch input
    Back door opener switch (open switch) not pushed
    Pulse generation

    1. *1: w/ Smart Key System
    2. *2: w/o Smart Key System
    If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may have a malfunction.


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Smart Key System)

B278932E15

  1. Disconnect the G53 certification ECU (smart key ECU assembly) connector.

  2. Measure the resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G53-22 (TSW5) - Body ground
    L - Body ground
    Back door opener switch signal
    Back door opener switch on
    Below 1 Ω
    G53-22 (TSW5) - Body ground
    L - Body ground
    Back door opener switch signal
    Back door opener switch off
    10 kΩ or higher
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the G53 certification ECU (smart key ECU assembly) connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G53-22 (TSW5) - Body ground
    L - Body ground
    Back door opener switch signal
    Back door opener switch off
    Pulse generation
    G53-22 (TSW5) - Body ground
    L - Body ground
    Back door opener switch signal
    Back door opener switch on
    Below 1 V
    If the result is not as specified, the certification ECU (smart key ECU assembly) may have a malfunction.