Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Smart Key System)

WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Smart Key System) > TERMINALS OF ECU

for Preparation Click here



CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B281049E05

  1. Disconnect the MB and G59 main body ECU (multiplex network body ECU) connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connectors disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    MB-11 (GND1) - Body ground
    -
    Ground
    Always
    Below 1 Ω
    MB-30 (BECU) - Body ground
    -
    Auxiliary battery power supply
    Ignition switch off
    11 to 14 V
    MB-29 (ACC) - Body ground
    -
    ACC power supply
    Ignition switch ACC
    11 to 14 V
    MB-29 (ACC) - Body ground
    -
    ACC power supply
    Ignition switch off
    Below 1 V
    MB-32 (IG) - Body ground
    -
    IG power supply
    Ignition switch ON (IG)
    11 to 14 V
    MB-32 (IG) - Body ground
    -
    IG power supply
    Ignition switch off
    Below 1 V
    G59-17 (KSW) - Body ground
    V - Body ground
    Unlock warning switch signal
    No key in ignition key cylinder
    10 kΩ or higher
    G59-17 (KSW) - Body ground
    V - Body ground
    Unlock warning switch signal
    Key in ignition key cylinder
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the MB and G59 main body ECU (multiplex network body ECU) connectors.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    3B-3 (ACT-) - Body ground
    R - Body ground
    Door lock motor unlock drive output (except driver door)
    Door control switch (power window regulator master switch assembly) or driver door key cylinder off
    Below 1 V
    3B-3 (ACT-) - Body ground
    R - Body ground
    Door lock motor unlock drive output (except driver door)
    Door control switch (power window regulator master switch assembly) or driver door key cylinder unlocked
    11 to 14 V
    3B-1 (ACT+) - Body ground
    Y - Body ground
    Door lock motor lock drive output (all doors)
    Door control switch (power window regulator master switch assembly) or driver door key cylinder off
    Below 1 V
    3B-1 (ACT+) - Body ground
    Y - Body ground
    Door lock motor lock drive output (all doors)
    Door control switch (power window regulator master switch assembly) or driver door key cylinder locked
    11 to 14 V
    3B-4 (ACTD) - Body ground
    L - Body ground
    Driver door lock motor unlock drive output
    Door control switch (power window regulator master switch assembly) or driver door key cylinder off
    Below 1 V
    3B-4 (ACTD) - Body ground
    L - Body ground
    Driver door lock motor unlock drive output
    Door control switch (power window regulator master switch assembly) or driver door key cylinder unlocked
    11 to 14 V
    3D-36 (FLCY) - Body ground
    R - Body ground
    Front door LH courtesy light switch input
    Front door LH open
    Below 1 V
    3D-36 (FLCY) - Body ground
    R - Body ground
    Front door LH courtesy light switch input
    Front door LH closed
    Pulse generation
    G59-19 (FRCY) - Body ground
    R - Body ground
    Front door RH courtesy light switch input
    Front door RH open
    Below 1 V
    G59-19 (FRCY) - Body ground
    R - Body ground
    Front door RH courtesy light switch input
    Front door RH closed
    Pulse generation
    G59-1 (LCTY) - Body ground
    L - Body ground
    Rear door LH courtesy light switch input
    Rear door LH open
    Below 1 V
    G59-1 (LCTY) - Body ground
    L - Body ground
    Rear door LH courtesy light switch input
    Rear door LH closed
    Pulse generation
    G59-6 (RCTY) - Body ground
    G - Body ground
    Rear door RH courtesy light switch input
    Rear door RH open
    Below 1 V
    G59-6 (RCTY) - Body ground
    G - Body ground
    Rear door RH courtesy light switch input
    Rear door RH closed
    Pulse generation
    G59-7 (LSFL) - Body ground
    L - Body ground
    Front door LH unlock detection switch input
    Front door LH unlocked
    Below 1 V
    G59-7 (LSFL) - Body ground
    L - Body ground
    Front door LH unlock detection switch input
    Front door LH locked
    Pulse generation
    G59-18 (LSFR) - Body ground
    L - Body ground
    Front door RH unlock detection switch input
    Front door RH unlocked
    Below 1 V
    G59-18 (LSFR) - Body ground
    L - Body ground
    Front door RH unlock detection switch input
    Front door RH locked
    Pulse generation
    G59-4 (PRG) - Body ground
    P - Body ground
    Signal output to door control and tire pressure monitoring system receiver assembly
    Key inserted in ignition key cylinder → Key pulled out of ignition key cylinder
    11 to 14 V → Pulse generation → 11 to 14 V
    G59-16 (RDA) - Body ground
    LG - Body ground
    Signal input from door control and tire pressure monitoring system receiver assembly
    Ignition switch off, all doors closed and door control transmitter module set sub-assembly switch not pressed
    11 to 14 V
    Ignition switch off, all doors closed and door control transmitter module set sub-assembly switch pressed
    Pulse generation
    G59-17 (KSW) - Body ground
    V - Body ground
    Key unlock warning switch input
    No key in ignition key cylinder
    Pulse generation
    Key in ignition key cylinder
    Below 1 V
    If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may have a malfunction.


CHECK DOOR CONTROL AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY

B280753E07

  1. Disconnect the M20 door control and tire pressure monitoring system receiver assembly connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connectors disconnected.


    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    M20-7 (+B) - Body ground
    BR - Body ground
    Auxiliary battery (power supply)
    Always
    11 to 14 V
    M20-12 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    1. If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the M20 door control and tire pressure monitoring system receiver assembly connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    M20-5 (PRG) - M20-12 (GND)
    W - W-B
    Signal input from main body ECU (multiplex network body ECU)
    Key inserted in ignition key cylinder → Key pulled out of ignition key cylinder
    11 to 14 V → Pulse generation → 11 to 14 V
    M20-4 (RDA) - M20-12 (GND)
    R - W-B
    Signal output to main body ECU (multiplex network body ECU)
    Ignition switch off, all doors closed and door control transmitter module set sub-assembly switch not pressed
    11 to 14 V
    Ignition switch off, all doors closed and door control transmitter module set sub-assembly switch pressed
    Pulse generation

    1. If the result is not as specified, the door control and tire pressure monitoring system receiver assembly may have a malfunction.