STEERING LOCK SYSTEM > DATA LIST / ACTIVE TEST |
| READ DATA LIST |
Turn the power switch off.
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Enter the following menus: Body Electrical / (desired system) / Data List.
According to the display on the Techstream, read the Data List.
Using the Techstream, confirm the Data List items to help determine the cause of the problem.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Shift P Signal | Shift position (P) signal / ON or OFF | ON: Shift lever in P OFF: Shift lever not in P |
|
| Steering Unlock Switch | State of steering unlock sensor signal output from steering lock actuator assembly / ON or OFF | ON: Steering unlocked (Power switch on (ACC)) OFF: Steering locked (Power switch off door opened) | This item can be used to determine the cause of problems when the steering does not lock or unlock.
|
| Str Lock/Unlock Wait T-Out | Steering lock or unlock malfunction / Yes or No | Yes: Steering lock/unlock timed out (Lock bar stuck, etc.) No: Steering locks/unlocks normally within specified time | The hybrid control system cannot be started when this item is "Yes". |
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Ignition Switch | State of certification ECU (smart key ECU assembly) IG power supply input / ON or OFF | ON: Power switch on (IG) OFF: Power switch off | This item displays "OFF" when the power switch is on (ACC). |
| #Codes | Number of DTCs / 0 to 255 | Number of stored DTCs displayed | - |
| Immobiliser | State of immobiliser system determined by certification ECU (smart key ECU assembly) / Set or Unset | Set: Engine immobiliser set (Power switch off) Unset: Engine immobiliser unset (Power switch on (ACC) or on (IG)) |
|
| Steering Lock Sleep Cond | Steering lock ECU sleep condition / Yes or No | - | - |
| Steering Lock Start Cond | Transmission state of steering lock ECU wake up signal / Yes or No | Yes: Wake up signal transmitted No: Wake up signal not transmitted | - |
| Engine Start Condition | State of hybrid control system permission signal determined by steering lock ECU and sent to certification ECU (smart key ECU assembly) / OK or NG | OK: Hybrid control system permitted NG: Hybrid control system prohibited |
|
| Sensor Value | Record of malfunction of position sensor in steering lock actuator assembly / OK or NG(Past) | OK: No record of lock/unlock sensor malfunction in steering lock actuator assembly NG(Past): Record of lock/unlock sensor in steering lock actuator assembly turning ON at same time exists | When this item displays "NG", the sensor inside the steering lock actuator assembly may be malfunctioning, or there may be a mechanical malfunction. |
| Power Supply Short | Record of malfunction of signal sent to steering lock motor (steering lock actuator assembly) from power management control ECU (short circuit) / OK or NG(Past) | OK: No record of malfunction (short circuit) NG(Past): Record of malfunction (short circuit) exists | This item records malfunctions in the circuit between the power management control ECU and steering lock motor (steering lock actuator assembly). |
| Motor Driver Short | Record of malfunction of motor activation circuit in steering lock actuator assembly (short circuit) (DTC B2781 stored) / OK or NG(Past) | OK: No record of malfunction (short circuit) NG(Past): Record of malfunction (short circuit) exists | This item records malfunctions in the motor activation circuit inside the steering lock actuator assembly (short circuit). |
| Lock/Unlock Receive | Reception state of steering lock or unlock request signal from certification ECU (smart key ECU assembly) / Yes or No | Yes: Record of receiving lock or unlock request signal exists No: No record of receiving lock or unlock request signal | - |
| Lock Bar Stuck Error | Record of lock bar not properly unlocking after being commanded to unlock for certain amount of time / OK or NG(Past) | OK: No record of stuck lock bar NG(Past): Record of stuck lock bar exists | - |
| Push Start Error | Record of malfunction of push-start function due to steering lock actuator assembly / OK or NG(Past) | OK: No record of push-start function malfunction NG(Past): Record push-start function malfunction exists | - |
| Engine Start Request | Reception state of hybrid control system permission signal determined by steering lock actuator assembly and sent to certification ECU (smart key ECU assembly) / OK or NG | OK: Receiving signal NG: Not receiving signal |
|
| S Code Check | Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) / OK or NG | OK: Verification result normal NG: Verification result abnormal | When a malfunction is present:
|
| L Code Check | Verification result between ID code box (immobiliser code ECU) and steering lock ECU / OK or NG | OK: Verification result normal NG: Verification result abnormal | When a malfunction is present:
|
| Unlock Request Receive | Reception state of steering unlock request signal by certification ECU (smart key ECU assembly) and sent to ID code box (immobiliser code ECU) / OK or NG
| OK: Within 10 seconds of turning power switch on (IG) or on (ACC) or starting hybrid control system NG: Except above |
|
| Lock Request Receive | Reception state of steering lock request signal by certification ECU (smart key ECU assembly) and sent to ID code box (immobiliser code ECU) / OK or NG
| OK: Within 10 seconds of opening any door with power switch off and shift lever in P NG: Except above | If this item does not change to "OK" even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning. |
| S Code Check(Past) | Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) (Past) / OK or NG(Past) | OK: Verification result normal NG(Past): Verification result abnormal (Past) | - |
| L Code Check(Past) | Verification result between ID code box (immobiliser code ECU) and steering lock ECU (Past) / OK or NG(Past) | OK: Verification result normal NG(Past): Verification result abnormal (Past) | - |
| Steering Lock | State of whether steering lock ECU has determined steering is locked / Set or Unset | Set: Steering locked Unset: Steering unlocked | If this item displays "Unset", the steering does not lock. |
| Steering Unlock | State of whether steering lock ECU determined steering is unlocked / Set or Unset | Set: Steering unlocked Unset: Steering locked | If this item displays "Unset", the steering does not unlock (hybrid control system cannot be started). |

| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| FL Door Courtesy SW | Front door courtesy light switch assembly LH / ON or OFF | ON: Front door LH closed OFF: Front door LH open | If this item does not change according to the actual state of the driver door, there is a malfunction in the door courtesy light switch or related part. |
| ACTIVE TEST |
Turn the power switch off.
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Enter the following menus: Body Electrical / (desired system) / Active Test.
According to the display on the Techstream, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| P Supply for Steering Lock | Power management control ECU | ON/OFF
| When performing this Active Test, make sure the following condition is met: The power switch is on (IG). |