Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/o Smart Key System)

DTC    B2799    Engine Immobiliser System Malfunction

for Preparation Click here


DESCRIPTION

This DTC is stored when one of the following occurs: 1) the power management control ECU detects errors in its own communications with the transponder key ECU assembly; 2) the power management control ECU detects errors in the communication lines; or 3) the ECU communication ID between the transponder key ECU assembly and power management control ECU is different and a hybrid control system start is attempted. Before troubleshooting for this DTC, make sure no engine immobiliser DTCs are output. If output, troubleshoot the engine immobiliser DTCs first.

DTC Code
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B2799
Either condition is met (1 trip detection logic*):
  1. A malfunction occurs in the communication or communication lines between the power management control ECU and transponder key ECU assembly.
  2. A communication code cannot be verified during communication between the power management control ECU and transponder key ECU assembly.
  1. Harness or connector
  2. Transponder key ECU assembly
  3. Power management control ECU
Either condition is met:
  1. 10 seconds after an hybrid control system start operation being performed (with the shift lever in P and the brake pedal depressed, turn the ignition switch to ON). If there is a malfunction, the hybrid control system stops (communication begins within 3 seconds of the hybrid control system start operation being performed, and DTCs are stored after 6 seconds).
  2. 10 seconds after the ignition switch is turned to ON after reconnecting the cable to the negative (-) auxiliary battery terminal (communication begins within 3 seconds of the ignition switch being turned to ON, and DTCs are stored after 6 seconds).
  1. *: Only output while a malfunction is present.

Vehicle Condition and Fail-safe Operation when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Operation when Malfunction Detected
Hybrid control system cannot be started
-

Related Data List and Active Test 
DTC Code
Data List and Active Test
B2799
-

WIRING DIAGRAM


B255097E21


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the transponder key ECU assembly, refer to the Registration (Click here).
  2. After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.

1.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2.CHECK FOR DTC
  1. Start the hybrid control system.

  1. Wait 10 seconds or more.

  1. Check for DTCs (Click here).

    HINT:
    Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.

    OK:
    DTC B2799 is not output.

    Result 
    Result
    Proceed to
    OK
    A
    NG (DTC B2799 is output)
    B
    NG (Other DTCs are output)
    C



B
Go to step 3

C
GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)  

3.INSPECT POWER MANAGEMENT CONTROL ECU (TERMINAL IMO)


  1. Using an oscilloscope, check the waveform.


    B302038E02


    Text in Illustration 
    *a
    Component with harness connected
    (Power Management Control ECU)
    *b
    Waveform
    Measurement Condition 
    Item
    Content
    Tester Connection
    G58-20 (IMO) - Body ground
    Tool Setting
    2 V/DIV., 500 ms./DIV.
    Condition
    Within 3 seconds after hybrid control system starts, or within 3 seconds after ignition switch first turned to ON after auxiliary battery disconnected and reconnected

    OK:
    Waveform is output normally (refer to illustration).

    Result 
    Result
    Proceed to
    Normal waveform
    A
    Terminal IMO stuck low (2.4 V or less)
    B
    Terminal IMO stuck high (12 V) or Abnormal waveform
    C



B
Go to step 7

C
Go to step 13
A


4.INSPECT POWER MANAGEMENT CONTROL ECU (TERMINAL IMI)


  1. Using an oscilloscope, check the waveform.


    B302039E02


    Text in Illustration 
    *a
    Component with harness connected
    (Power Management Control ECU)
    *b
    Waveform
    Measurement Condition 
    Item
    Content
    Tester Connection
    G58-21 (IMI) - Body ground
    Tool Setting
    2 V/DIV., 500 ms./DIV.
    Condition
    Within 3 seconds after hybrid control system starts, or within 3 seconds after ignition switch first turned to ON after auxiliary battery disconnected and reconnected

    OK:
    Waveform is output normally (refer to illustration).

    Result 
    Result
    Proceed to
    Normal waveform
    A
    Not output waveform or abnormal waveform
    B



B
Go to step 9
A


5.REGISTER ECU COMMUNICATION ID
  1. Reregister the ECU communication ID (Click here).


NEXT


6.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
  1. Check that the hybrid control system starts with an already registered vehicle key.

    OK:
    Hybrid control system starts normally.



NG
Go to step 13
OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE) 

7.INSPECT POWER MANAGEMENT CONTROL ECU (IMO TERMINAL VOLTAGE)


    B302040E02
  1. Disconnect the G58 power management control ECU connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.
    Result 
    Result
    Proceed to
    Terminal IMO stuck low (2.4 V or less)
    A
    Terminal IMO stuck high (12 V)
    B
    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)



B
Go to step 13
A


8.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - POWER MANAGEMENT CONTROL ECU AND BODY GROUND)
  1. Disconnect the G46 transponder key ECU assembly connector.

  1. Disconnect the G58 power management control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G46-12 (EFII) - G58-20 (IMO)
    Always
    Below 1 Ω
    G46-12 (EFII) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.REPLACE TRANSPONDER KEY ECU ASSEMBLY
  1. Replace the transponder key ECU assembly (Click here).


NEXT


10.REGISTER KEY
  1. Reregister the key (Click here).


NEXT


11.REGISTER ECU COMMUNICATION ID
  1. Reregister the ECU communication ID (Click here).


NEXT


12.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
  1. Check that the hybrid control system starts with an already registered vehicle key.

    OK:
    Hybrid control system starts normally.



NG
REPLACE POWER MANAGEMENT CONTROL ECU (Click here)
OK

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE) 

13.REPLACE POWER MANAGEMENT CONTROL ECU
  1. Temporarily replace the power management control ECU with a new one (Click here).


NEXT


14.REGISTER ECU COMMUNICATION ID
  1. Reregister the ECU communication ID (Click here).


NEXT


15.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
  1. Check that the hybrid control system starts with an already registered vehicle key.

    OK:
    Hybrid control system starts normally.



NG
REPLACE TRANSPONDER KEY ECU ASSEMBLY (Click here)
OK

END (POWER MANAGEMENT CONTROL ECU WAS DEFECTIVE)