Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/ Smart Key System)

DTC    B2799    Engine Immobiliser System Malfunction

for Preparation Click here


DESCRIPTION

When there are communication malfunctions between the power management control ECU and ID code box (immobiliser code ECU), or when the communication ID codes do not match, the power management control ECU stores this DTC.

DTC Code
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B2799
Either condition is met (1 trip detection logic*):
  1. A malfunction in the communication or communication lines between the power management control ECU and ID code box (immobiliser code ECU).
  2. A matching communication code cannot be verified during communication between the power management control ECU and ID code box (immobiliser code ECU).
  1. ID code box (immobiliser code ECU)
  2. Power management control ECU
  3. Wire harness or connector
Either condition is met:
  1. 10 seconds after a hybrid control system start operation (with the shift lever in P and the brake pedal depressed, the power switch is pressed while carrying the key). If there is a malfunction, the hybrid control system does not start (communication begins within 3 seconds of the hybrid control system start operation, and DTCs are stored after 6 seconds).
  2. 10 seconds after the power switch is turned on (IG) after reconnecting the cable to the negative (-) auxiliary battery terminal (communication begins within 3 seconds of the power switch being turned on (IG), and DTCs are stored after 6 seconds).
  1. *: Only output while a malfunction is present.

Vehicle Condition and Fail-safe Operation when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Operation when Malfunction Detected
Hybrid control system cannot be started
-

Related Data List and Active Test 
DTC Code
Data List and Active Test
B2799
-

WIRING DIAGRAM


B271006E16


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the ID code box (immobiliser code ECU) or power management control ECU, refer to Registration (Click here).
  2. After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.

HINT:
When DTC B2799 and the certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.

1.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2.CHECK FOR DTC
  1. Start the hybrid control system.

  1. Wait 10 seconds or more.

  1. Check for DTCs (Click here).

    HINT:
    Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.

    OK:
    DTC B2799 is not output.

    Result 
    Result
    Proceed to
    OK
    A
    NG (DTC B2799 is output)
    B
    NG (Other DTCs are output)
    C



B
Go to step 3

C
GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)  

3.INSPECT POWER MANAGEMENT CONTROL ECU (TERMINAL IMO)


  1. Using an oscilloscope, check the waveform.


    B302038E02


    Text in Illustration 
    *a
    Component with harness connected
    (Power Management Control ECU)
    *b
    Waveform
    Measurement Condition 
    Item
    Content
    Tester Connection
    G58-20 (IMO) - Body ground
    Tool Setting
    2 V/DIV., 500 ms./DIV.
    Condition
    Within 3 seconds after hybrid control system starts, or within 3 seconds after power switch first turned to on (IG) after auxiliary battery disconnected and reconnected

    OK:
    Waveform is output normally (refer to illustration).

    Result 
    Result
    Proceed to
    Normal waveform
    A
    Terminal IMO stuck low (2.4 V or less)
    B
    Terminal IMO stuck high (12 V) or Abnormal waveform
    C



B
Go to step 7

C
Go to step 12
A


4.INSPECT POWER MANAGEMENT CONTROL ECU (TERMINAL IMI)


  1. Using an oscilloscope, check the waveform.


    B302039E02


    Text in Illustration 
    *a
    Component with harness connected
    (Power Management Control ECU)
    *b
    Waveform
    Measurement Condition 
    Item
    Content
    Tester Connection
    G58-21 (IMI) - Body ground
    Tool Setting
    2 V/DIV., 500 ms./DIV.
    Condition
    Within 3 seconds after hybrid control system starts, or within 3 seconds after power switch first turned to on (IG) after auxiliary battery disconnected and reconnected

    OK:
    Waveform is output normally (refer to illustration).

    Result 
    Result
    Proceed to
    Normal waveform
    A
    Not output waveform or abnormal waveform
    B



B
Go to step 9
A


5.REGISTER ECU COMMUNICATION ID
  1. Reregister the ECU communication ID (Click here).


NEXT


6.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
  1. Check that the hybrid control system starts with an already registered vehicle key.

    OK:
    Hybrid control system starts normally.



NG
Go to step 12
OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE) 

7.INSPECT POWER MANAGEMENT CONTROL ECU (IMO TERMINAL VOLTAGE)


    B302040E02
  1. Disconnect the G58 power management control ECU connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.
    Result 
    Result
    Proceed to
    Terminal IMO stuck low (2.4 V or less)
    A
    Terminal IMO stuck high (12 V)
    B
    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)



B
Go to step 12
A


8.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - ID CODE BOX AND BODY GROUND)
  1. Disconnect the G49 ID code box (immobiliser code ECU) connector.

  1. Disconnect the G58 power management control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G49-3 (EFII) - G58-20 (IMO)
    Always
    Below 1 Ω
    G58-20 (IMO) - Body ground
    Always
    10 kΩ or higher
    G49-4 (EFIO) - G58-21 (IMI)
    Always
    Below 1 Ω
    G58-21 (IMI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
  1. Replace the ID code box (immobiliser code ECU) (Click here).


NEXT


10.REGISTER ECU COMMUNICATION ID
  1. Reregister the ECU communication ID (Click here).


NEXT


11.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
  1. Check that the hybrid control system starts with an already registered vehicle key.

    OK:
    Hybrid control system starts normally.



NG
REPLACE POWER MANAGEMENT CONTROL ECU (Click here)
OK

END (ID CODE BOX (IMMOBILISER CODE ECU) WAS DEFECTIVE) 

12.REPLACE POWER MANAGEMENT CONTROL ECU
  1. Temporarily replace the power management control ECU with a new one (Click here).


NEXT


13.REGISTER ECU COMMUNICATION ID
  1. Reregister the ECU communication ID (Click here).


NEXT


14.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
  1. Check that the hybrid control system starts with an already registered vehicle key.

    OK:
    Hybrid control system starts normally.



NG
REPLACE ID CODE BOX (IMMOBILISER CODE ECU) (Click here)
OK

END (POWER MANAGEMENT CONTROL ECU WAS DEFECTIVE)