Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT

AIR CONDITIONING UNIT > REASSEMBLY

for Preparation Click here



1. INSTALL NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY


    E238105E01
  1. Using the reference point, install the No. 1 air conditioning radiator damper servo sub-assembly with the 2 screws.
    Text in Illustration 
    *a
    Reference Point



2. INSTALL NO. 2 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY


    E235041E01
  1. Using the reference point, install the No. 2 air conditioning radiator damper servo sub-assembly with the 2 screws.
    Text in Illustration 
    *a
    Reference Point

  1. Install the No. 2 air conditioning radiator damper servo sub-assembly with the 2 screws.



3. INSTALL DRAIN COOLER HOSE


    E248840
  1. Align the drain cooler hose fitting and the protrusion of the lower heater case as shown in the illustration to connect the drain cooler hose to the heater case.



4. INSTALL FRONT EVAPORATOR TEMPERATURE SENSOR (NO. 1 COOLER THERMISTOR)


    E234955E01
  1. Install the front evaporator temperature sensor (No. 1 cooler thermistor) as shown in the illustration.

    Installation Position:
    Mark
    Measurement
    A
    61.1 mm (2.41 in.)
    B
    47.7 mm (1.88 in.)
    C
    50 mm (1.97 in.)

    Text in Illustration 
    *a
    Secured Part
    *b
    Sensor Part

    NOTICE:
    1. Be sure to insert the thermistor only once because reinserting it into the same position will not allow it to be firmly secured.
    2. When reusing the evaporator, insert the thermistor one row next to the one that has been used previously (X in the illustration).
    3. After inserting the thermistor, do not apply excessive force to the wire.
    4. Directly insert the thermistor until the edge of plastic case "a" comes into contact with evaporator "b".



5. INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY


    E235039
  1. Sufficiently apply compressor oil to 2 new O-rings and the fitting surface of the No. 1 cooler evaporator sub-assembly.

    Compressor oil:
    ND-OIL 11 or equivalent

  1. Install the 2 O-rings to the No. 1 cooler evaporator sub-assembly.

    NOTICE:
    Keep the O-rings and O-ring fitting surfaces free of foreign matter.



    E235038
  1. Install the No. 1 cooler evaporator sub-assembly with the No. 1 cooler thermistor to the upper heater case as shown in the illustration.



    E238230
  1. Engage the 4 claws and install the lower heater case.

  1. Engage the clamp and connect the connector to the lower heater case.



    E288000
  1. Install the 6 screws.



6. INSTALL COOLER EXPANSION VALVE


    E238228
  1. Using a 4 mm hexagon wrench, install the cooler expansion valve with the 2 hexagon bolts.

    Torque:
    3.5 N*m{ 36 kgf*cm , 31 in.*lbf }



7. INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY


    E238232
  1. Install the heater radiator unit sub-assembly to the air conditioner radiator assembly.



    E238226
  1. Engage the 3 claws and install the clamp.



8. INSTALL HEATER BRACKET (for Cold Area Specification Vehicles)


    E238225
  1. Install the heater bracket with the bolt.



9. INSTALL QUICK HEATER ASSEMBLY (for Cold Area Specification Vehicles)
  1. Install the quick heater assembly with the 2 screws.

  1. Engage the clamp.

  1. Connect the connector.

  1. Engage the clamp.

  1. Connect the earth wire with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }