Home › Engine / Hybrid System › 1NZ-FXE FUEL › FUEL PUMP

FUEL PUMP > INSTALLATION

for Preparation Click here



1. INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY


    A265014E01
  1. Install a new fuel suction tube set gasket onto the fuel tank as shown in the illustration.
    Text in Illustration 
    *1
    Fuel Suction Tube Set Gasket



    A267904E01
  1. Set the fuel suction tube with pump and gauge assembly to the fuel tank.
    Text in Illustration 
    *a
    Protrusion
    *b
    Notch

    NOTICE:
    Make sure that the fuel sender gauge arm does not bend.

  1. Align the protrusions of the fuel suction tube with pump and gauge assembly with the notches of the fuel tank.



2. INSTALL FUEL PUMP GAUGE RETAINER


    A267905E01
  1. While holding the fuel suction tube assembly with pump and gauge by hand to prevent it from tilting, align the mark on a new fuel pump gauge retainer with the start mark on the fuel tank and tighten the fuel pump gauge retainer 180° by hand.
    Text in Illustration 
    *a
    Start Mark
    *b
    Mark
    *c
    Front

    HINT:
    1. Check that there is no damage, dents, foreign matter or other defects on the threads of the fuel tank.



    A267900E01
  1. Temporarily install the SST plate and claws to the fuel pump gauge retainer.
    Text in Illustration 
    *1
    SST
    (Plate)
    *2
    SST
    (Claw)
    *3
    Rib

    SST
    09808-14030   (09808-01030, 09808-01040, 09808-01050)

    HINT:
    Engage the SST claws securely with the fuel pump gauge retainer ribs to secure SST.

  1. While pressing the claws of SST to the fuel pump gauge retainer ribs securely, tighten the bolts.

    HINT:
    Install SST while pressing the SST claws toward the fuel pump gauge retainer (toward the center of SST).

  1. Install the SST handle.



    A267906E01
  1. Tighten the fuel pump gauge retainer approximately 360° so that the mark on the retainer comes within the range shown in the illustration.
    Text in Illustration 
    *1
    SST
    (Handle)
    *2
    SST
    (Plate)
    *3
    SST
    (Claw)
    *a
    Mark
    *b
    Front

    SST
    09808-14030   (09808-01010, 09808-01020, 09808-01030, 09808-01040, 09808-01050)

    NOTICE:
    1. Do not use any tools other than specified in this operation. Damage to the fuel pump gauge retainer or the fuel tank may result.
    2. Do not press down on SST excessively as this may make the retainer hard to rotate, and may damage components.
    3. Make sure to rotate the SST handle horizontally. If the SST handle is rotated at an angle, SST may come off.
    4. Do not spin SST too fast or use an impact wrench as this may result in damage to components.
    5. If SST comes off of the retainer, loosen the SST bolts and reinstall SST.

    HINT:
    1. Lightly press down on SST to prevent it from separating from the retainer. While pressing SST, rotate the handle slowly to tighten the retainer.
    2. The ribs on the fuel pump gauge retainer can be fitted into the tips of SST.



3. CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY


    A267907E01
  1. Push the fuel tube joint in the plug of the fuel suction plate, then install the tube joint clip.
    Text in Illustration 
    *1
    Tube Joint Clip
    *2
    Fuel Tube Joint
    *3
    O-ring
    *4
    Collar
    *a
    CORRECT
    *b
    INCORRECT

    NOTICE:
    1. Check that there is no damage or foreign matter around the connecting parts of the fuel tube joint and plug before performing this work.
    2. Check that the fuel tube joint is securely inserted to the end.
    3. Check that the tube joint clip is on the collar of the fuel tube joint.
    4. After installing the tube joint clip, check that the fuel tube joint cannot be pulled out.

  1. Connect the fuel pump connector.



4. CONNECT FUEL TANK VENT HOSE SUB-ASSEMBLY


    A267898E02
  1. Push in the fuel tank vent hose connector to the fuel suction tube with pump and gauge assembly and push the retainer so that the claws engage.
    Text in Illustration 
    *1
    Retainer
    V100135
    Push

    NOTICE:
    1. Check that there is no damage or foreign matter around the connecting parts of the fuel tank vent hose connector and fuel suction tube assembly before performing this work.
    2. After connecting the fuel tank vent hose, check that the fuel tank vent hose is securely connected by pulling on the fuel tank vent hose connector.



5. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



6. INSPECT FOR FUEL LEAK
  1. Check fuel pump operation.

    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch to ON (IG) and turn the Techstream on.

      NOTICE:
      Do not start the engine.

    3. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

    4. Check for pressure in the fuel inlet tube from the fuel line. Check that sounds of fuel flowing from the fuel tank can be heard. If no sounds can be heard, check the integration relay, fuel pump, ECM and wiring connectors.

  1. Inspect for fuel leaks.

    1. Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.

  1. Turn the ignition switch off.

  1. Disconnect the Techstream from the DLC3.



7. INSTALL REAR FLOOR SERVICE HOLE COVER


    A267868E01
  1. Install the rear floor service hole cover with new butyl tape.



8. INSTALL CROSS ANCHOR BRACKET SUB-ASSEMBLY
(Click here)