BLACK OUT TAPE (for Center Pillar) > INSTALLATION |
| 1. REPAIR INSTRUCTION |
Clean the vehicle body surface.
Using a heat light, heat the vehicle body surface.
| Item | Temperature |
| Vehicle Body | 40 to 60°C (104 to 140°F) |
Wipe off any tape adhesive residue with cleaner.
Installation temperature
When the ambient temperature is below 15°C (59°F), perform the installation procedure after warming the vehicle body surface (installation surface of the door frame) and tape up to between 20 and 30°C (68 and 86°F) using a heat light. When the ambient temperature is above 35°C (95°F), cool the vehicle body surface (installation surface of the door frame) and tape down to between 20 and 30°C (68 and 86°F) prior to installation.
Before installation
Remove any coating roughness or dirt on and around the vehicle body surface where the tape will be installed (installation surface of the door frame). If any roughness or dirt remains when pressing the tape onto the surface, air will be trapped under the tape and result in a poor appearance.
Key points for handling the tape
The tape bends and rolls up easily. Store the tape between flat pieces of cardboard or other similar objects and keep it dry and flat.
Key points for installation of the tape (how to use a squeegee and installation procedure for flat surfaces)
To avoid air bubbles, slightly raise the part of the tape that is going to be applied so that its adhesive surface does not touch the vehicle body while applying the tape. Tilt the squeegee at 40 to 50° (pressing forward) or 30 to 45° (pulling) to the vehicle body surface and press the tape onto the vehicle body surface with a force of 20 to 30 N (2 to 3 kgf, 4.5 to 6.7 lbf) at a constant slow speed of 3 to 7 cm (1.18 to 2.76 in.) per second.

| *A | Pressing Forward | *B | Pulling |
| *1 | Non-padded Side | *2 | Padded Side |
| *3 | Squeegee | *4 | Black Out Tape |
| *5 | Release Paper | - | - |
| *a | Side View | - | - |
| Area | Measurement |
| A | 10 to 20 mm (0.393 to 0.787 in.) |
| B | 30 to 70 mm/sec. (1.18 to 2.76 in./sec.) |
| C | 40 to 50° (for pressing forward) |
| D | 30 to 45° (for pulling) |
Key points for installation of the tape (how to use a squeegee and installation procedure for hemmed surfaces)
![]() |
If it is difficult to apply the tape, install it in several steps as shown in the illustration. Use your fingers or the padded surface of a squeegee to slowly apply the tape to the hem of the vehicle, especially for a small hem.
| *1 | Squeegee |
| *2 | Hem |
| *a | First |
| *b | Second |
| *c | Third |
Key points for installation of the tape (how to use a squeegee and installation procedure for corners)
Remove the release paper and apply the tape carefully with your fingers.
Before applying the tape to each corner, heat the tape using a heat light and gradually apply it, avoiding wrinkles on the tape to achieve a neat finish.
Check after installation
After completing the application, check if the tape is applied neatly. If the tape is not applied neatly, reapply using new tape.
| 2. INSTALL NO. 3 BLACK OUT TAPE |
Apply new No. 3 black out tape to the positions shown in the illustration.

| *1 | Edge of curved surface | - | - |
| Dimension | Measurement |
| a | 11.0 mm (0.433 in.) |
| b | -1.0 to 1.0 mm (-0.0394 to 0.0394 in.) |
| c | -1.0 to 1.0 mm (-0.0394 to 0.0394 in.) |