Home › Drivetrain › P510 HYBRID TRANSMISSION / TRANSAXLE › SHIFT LEVER

SHIFT LEVER > INSPECTION

for Preparation Click here



1. INSPECT LOWER SHIFT LEVER ASSEMBLY (w/ Smart Key System)


    C249921E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    4 (IG) - Body ground
    Power switch on (IG)
    11 to 14 V
    Power switch off
    Below 1 V
    8 (STP) - Body ground
    Brake pedal depressed
    11 to 14 V
    Brake pedal released
    Below 1 V

    Text in Illustration 
    *a
    Component with harness connected
    (Lower Shift Lever Assembly)

    HINT:
    Do not disconnect the lower shift lever assembly connector.



    C249921E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    7 (E) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component with harness connected
    (Lower Shift Lever Assembly)

    HINT:
    Do not disconnect the lower shift lever assembly connector.



  1. Inspect shift lock solenoid



      C249922
    1. Disconnect the shift lock solenoid connector.



    2. C197452E09
    3. Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

      Standard Resistance:
      Tester Connection
      Shift Lever Position
      Specified Condition
      4 (P) - 3 (E2)
      P
      10 kΩ or higher
      Other than P
      Below 1 Ω

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Shift Lock Solenoid)
      1. If the result is not as specified, replace the lower shift lever assembly.
      2. If the shift lock does not operate when the power source of the lower shift lever assembly is normal and the resistance between the body ground and the shift lock solenoid is as specified, replace the lower shift lever assembly.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1 (SLS+) - 2 (SLS-)
      Always
      112 Ω

      1. If the result is not as specified, replace the lower shift lever assembly.
      2. If the shift lock does not operate when the power source of the lower shift lever assembly is normal and the resistance between the body ground and the shift lock solenoid is as specified, replace the lower shift lever assembly.



2. INSPECT LOWER SHIFT LEVER ASSEMBLY (w/o Smart Key System)


    C249921E03
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    1 (ACC) - Body ground
    Ignition switch ON (IG)
    11 to 14 V
    Ignition switch ACC
    11 to 14 V
    Ignition switch off
    Below 1 V
    8 (STP) - Body ground
    Brake pedal depressed
    11 to 14 V
    Brake pedal released
    Below 1 V
    5 (KLS+) - Body ground
    Ignition switch ACC and shift lever in P
    Below 1 V
    Ignition switch ACC and shift lever except in P
    11 to 14 V
    4 (IG) - Body ground
    Ignition switch ON (IG)
    11 to 14 V
    Ignition switch off
    Below 1 V

    Text in Illustration 
    *a
    Component with harness connected
    (Lower Shift Lever Assembly)

    HINT:
    Do not disconnect the lower shift lever assembly connector.



    C249921E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Value
    7 (E) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component with harness connected
    (Lower Shift Lever Assembly)

    HINT:
    Do not disconnect the lower shift lever assembly connector.



  1. Inspect shift lock solenoid



      C249922
    1. Disconnect the shift lock solenoid connector.



    2. C197452E09
    3. Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

      Standard Resistance:
      Tester Connection
      Shift Lever Position
      Specified Condition
      4 (P) - 3 (E2)
      P
      10 kΩ or higher
      Other than P
      Below 1 Ω

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Shift Lock Solenoid)
      1. If the result is not as specified, replace the lower shift lever assembly.
      2. If the shift lock does not operate when the power source of the lower shift lever assembly is normal and the resistance between the body ground and the shift lock solenoid is as specified, replace the lower shift lever assembly.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1 (SLS+) - 2 (SLS-)
      Always
      112 Ω

      1. If the result is not as specified, replace the lower shift lever assembly.
      2. If the shift lock does not operate when the power source of the lower shift lever assembly is normal and the resistance between the body ground and the shift lock solenoid is as specified, replace the lower shift lever assembly.