Home › Engine / Hybrid System › 1NZ-FXE FUEL › FUEL TANK

FUEL TANK > REMOVAL

for Preparation Click here



1. PRECAUTION


    A267908E01
  1. When removing and installing the fuel tank assembly, arrange the inlet hose as shown in the illustration, and secure the fuel tank assembly using a cord or similar.
    Text in Illustration 
    *1
    Cord

    NOTICE:
    Depending on the arrangement of the inlet hose during removal, the inlet hose and rear suspension may interfere and cause fuel leakage.



2. REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
(Click here)


3. DRAIN FUEL


4. REMOVE FUEL TANK CAP ASSEMBLY


5. REMOVE FRONT NO. 4 FLOOR HEAT INSULATOR


    A267873
  1. Remove the 2 nuts and front No. 4 floor heat insulator.



6. REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY


    A267874
  1. Pinch and remove the clip as shown in the illustration.

  1. Remove the bolt and No. 1 fuel tank protector sub-assembly.



7. REMOVE NO. 1 FUEL TUBE PROTECTOR


    A275852E01
  1. Remove the No. 1 fuel tube protector from the fuel tube connector.
    Text in Illustration 
    *1
    No. 1 Fuel Tube Protector



8. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY


    A267909E01
  1. Pull the tabs of the retainer to disengage the lock claws and pull out the fuel tank main tube sub-assembly.
    Text in Illustration 
    *1
    Fuel Tank Main Tube Sub-assembly
    *2
    Fuel Tank Pipe Setting Holder
    *3
    Retainer
    *4
    Nylon Tube
    *5
    O-ring
    *6
    Fuel Tube Connector
    *7
    Fuel Pipe

    NOTICE:
    1. Check that there are no scratches or foreign matter around the connected part of the fuel tube connector and fuel pipe before performing this work.
    2. Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the fuel pipe.
    3. Only disconnect the fuel tube connector by hand.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected part by covering it with a plastic bag after disconnecting the fuel tube connector.
    6. If the fuel tube connector and fuel pipe are stuck, push and pull to release them.

  1. Disengage the clamp and separate the fuel tank pipe setting holder.



9. REMOVE CHARCOAL CANISTER ASSEMBLY


    A267667E02
  1. Disconnect the connector from the charcoal canister leak detection pump sub-assembly.

  1. Disconnect the air line tube.

    1. Push the air line tube firmly toward the charcoal canister side.

    2. Pull the air line tube as shown in the illustration.

    3. Pull out the air line tube.
      Text in Illustration 
      *1
      Retainer
      *2
      Air Line Tube
      V100136
      Pull

      NOTICE:

      1. A275787E01
        Remove any dirt or foreign matter on the tube connector before performing this work.
        Text in Illustration 
        *1
        Tube Connector
        *2
        O-ring
        *3
        Retainer
        *4
        Pipe (Leak Detection Pump Sub-Assembly)
      2. Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the tube connector has an O-ring that seals the pipe.
      3. Perform this work by hand. Do not use any tools.
      4. Do not forcibly bend, twist or turn the air line tube.
      5. Protect the disconnected parts by covering them with plastic bags after disconnecting the air line tube.
      6. If the tube connector and pipe are stuck, push and pull on them to release.



    A267666
  1. Disconnect the purge line hose.



    A269228E01
  1. Disconnect the vent line tube.

    1. Push the vent line tube firmly toward the charcoal canister side.

    2. Pinch the vent line tube as shown in the illustration.

    3. Pull out the vent line tube.
      Text in Illustration 
      *1
      Retainer
      *2
      Vent Line Tube
      V100135
      Pinch
      V100136
      Pull

      NOTICE:

      1. A275787E01
        Remove any dirt or foreign matter on the tube connector before performing this work.
        Text in Illustration 
        *1
        Tube Connector
        *2
        O-ring
        *3
        Retainer
        *4
        Pipe (Charcoal Canister Assembly)
      2. Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the tube connector has an O-ring that seals the pipe.
      3. Perform this work by hand. Do not use any tools.
      4. Do not forcibly bend, twist or turn the air line tube.
      5. Protect the disconnected parts by covering them with plastic bags after disconnecting the air line tube.
      6. If the tube connector and pipe are stuck, push and pull on them to release.



    A267665
  1. Remove the 3 bolts and charcoal canister assembly.



10. REMOVE REAR WHEEL (for LH Side)


11. REMOVE FUEL TANK ASSEMBLY


    A267910
  1. Remove the bolt, disengage the clamp and separate the fuel tank filler pipe assembly.



    A267879
  1. Support the fuel tank assembly using an engine lifter.



    A261048
  1. Remove the 4 bolts and fuel tank assembly.

    NOTICE:
    1. Slowly operate the engine lifter to lower the fuel tank.
    2. Do not drop the fuel tank.



12. REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY


    A267911E01
  1. Disengage the clamp and remove the fuel tank pipe setting holder.
    Text in Illustration 
    *1
    Fuel Tank Pipe Setting Holder
    *2
    Fuel Tank Main Tube Sub-assembly

  1. Release the 2 clamps, and then remove the fuel tank main tube sub-assembly.



13. REMOVE FUEL TANK VENT HOSE SUB-ASSEMBLY


    A267912
  1. Release the clamp, and then remove the fuel tank vent hose sub-assembly from the fuel tank assembly.



14. REMOVE FUEL TANK FILLER PIPE PROTECTOR


    A259865E01
  1. Remove the clip from the fuel tank filler pipe protector.
    Text in Illustration 
    *1
    No. 1 Fuel Tube Support Protector
    *2
    Fuel Tank Filler Pipe Protector

  1. Disengage the 2 claws and remove the No. 1 fuel tube support protector.

  1. Disengage the 2 claws and remove the fuel tank filler pipe protector.



15. REMOVE BREATHER TUBE CLAMP


    A267913
  1. Disengage the claw and clamp as shown in the illustration, and remove the breather tube clamp.