Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM

LIGHTING SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B281049E05

  1. Disconnect the 3B, 3C and 3E instrument panel junction block assembly connectors.

  2. Measure the voltage according to the value(s) in the table below.

    Terminal No.
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    3E-1 - Body ground
    B - Body ground
    Auxiliary battery power supply
    Ignition switch off
    11 to 14 V
    3C-21 - Body ground
    L - Body ground
    Auxiliary battery power supply
    Ignition switch off
    11 to 14 V
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    3B-8 - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  4. Reconnect the 3B, 3C and 3E instrument panel junction block assembly connectors.

  5. Measure the voltage and check for pulses according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    3B-37 - Body ground
    L - Body ground
    ACC power supply
    Ignition switch ACC
    11 to 14 V
    Ignition switch off
    Below 1 V
    3A-29 - Body ground
    SB - Body ground
    IG power supply
    Ignition switch ON (IG)
    11 to 14 V
    Ignition switch off
    Below 1 V
    3A-40 - Body ground
    L - Body ground
    IG signal input
    Ignition switch ON (IG)
    11 to 14 V
    Ignition switch off
    Below 1 V
    3A-54 - Body ground
    Y - Body ground
    IG signal output
    Ignition switch ON (IG)
    11 to 14 V
    Ignition switch off
    Below 1 V
    G59-15 (DOMR)- Body ground
    BR - Body ground
    DOME CUT relay drive output
    DOME CUT relay off
    11 to 14 V
    DOME CUT relay on
    Below 1 V
    3C-4 - Body ground
    G - Body ground
    Interior lights power supply
    DOME CUT relay off
    Below 1 V
    DOME CUT relay on
    11 to 14 V
    3A-5 - Body ground
    BE - Body ground
    Interior lights power supply
    DOME CUT relay off
    Below 1 V
    DOME CUT relay on
    11 to 14 V
    3B-6 - Body ground
    B - Body ground
    Interior lights drive output
    Ignition switch off, interior lights off (when operated by illuminated entry system)
    11 to 14 V
    Ignition switch off, interior lights on (when operated by illuminated entry system)
    Below 1 V
    3D-6 - Body ground*2
    L - Body ground
    No. 1 Luggage Compartment Light power supply
    DOME CUT relay off
    Below 1 V
    DOME CUT relay on
    11 to 14 V
    3D-35 - Body ground
    B - Body ground
    Back door courtesy light switch input
    Back door open
    Below 1 V
    Back door closed
    11 to 14 V
    3D-36 - Body ground
    R - Body ground
    Front door courtesy light switch LH input
    Front door LH open
    Below 1 V
    Front door LH closed
    Pulse generation
    G59-19 (FRCY) - Body ground
    R - Body ground
    Front door courtesy light switch RH input
    Front door RH open
    Below 1 V
    Front door RH closed
    Pulse generation
    G59-1 (LCTY) - Body ground
    L - Body ground
    Rear door courtesy light switch LH input
    Rear door LH open
    Below 1 V
    Rear door LH closed
    Pulse generation
    G59-6 (RCTY) - Body ground
    G - Body ground
    Rear door courtesy light switch RH input
    Rear door RH open
    Below 1 V
    Rear door RH closed
    Pulse generation
    G59-7 (LSFL) - Body ground
    L - Body ground
    Front door unlock detection switch LH input
    Front door LH locked
    Pulse generation
    Front door LH unlocked
    Below 1 V
    G59-18 (LSFR) - Body ground
    L - Body ground
    Front door unlock detection switch RH input
    Front door RH locked
    Pulse generation
    Front door RH unlocked
    Below 1 V
    3D-24 - Body ground*1
    Y - Body ground
    Rear door unlock detection switch LH input
    Rear door LH and rear door RH locked
    Pulse generation
    Rear door LH or rear door RH unlocked
    Below 1 V
    3D-25 - Body ground*1
    V - Body ground
    Rear door unlock detection switch RH input
    Rear door LH and rear door RH locked
    Pulse generation
    Rear door LH or rear door RH unlocked
    Below 1 V

    1. *1: w/ Smart Key System
    2. *2: w/ No. 1 Luggage Compartment Light Assembly
    If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may be malfunctioning.


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B278932E52

  1. Measure the voltage according to the value(s) in the table below.

    NOTICE:
    Check that the light intensity of the light control rheostat is set to maximum.


    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G54-6 (SWIL) - G55-6 (AGND)
    R - B
    Power switch illumination drive output
    Power switch illumination on
    11 to 14 V
    Power switch illumination off
    Below 1 V
    1. If the result is not as specified, the certification ECU (smart key ECU assembly) may be malfunctioning.