Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HV RELAY ASSEMBLY

HV RELAY ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL HYBRID BATTERY JUNCTION BLOCK ASSEMBLY

CAUTION:
Wear insulated gloves.

  1. Install the hybrid battery junction block assembly with the 3 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the connector to the hybrid battery junction block assembly.

    NOTICE:
    The connector should be connected securely.

  1. Using an insulated tool, install the 2 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    NOTICE:
    Be sure to use a torque wrench to tighten the bolts.



    A266778
  1. Connect the terminal cover.

    NOTICE:
    The terminal cover should be connected securely.



2. INSTALL NO. 2 HYBRID BATTERY SHIELD SUB-ASSEMBLY

CAUTION:
Wear insulated gloves.

  1. Install the No. 2 hybrid battery shield sub-assembly with the 2 bolts and nut.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Move the HV battery to the installation position.

  1. Install the HV battery with the 2 bolts and 2 nuts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

  1. Connect the 4 connectors and 4 clamps.

    NOTICE:
    The connector should be connected securely.



3. CONNECT FRAME WIRE

CAUTION:
Wear insulated gloves.



    A266764E01
  1. Connect the 2 connectors.
    Text in Illustration 
    *1
    Shielded Wire Ground

    NOTICE:
    1. Make sure that the ends of the frame wire do not cross over each other.
    2. The connector should be connected securely.

  1. Connect the shielded wire ground.



4. INSTALL NO. 1 HYBRID VEHICLE BATTERY COVER PANEL LH

CAUTION:
Wear insulated gloves.

  1. Install the No. 1 hybrid vehicle battery cover panel LH with the 4 nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



    A266762E01
  1. Install the battery cover lock striker, then push the button to lock it.
    Text in Illustration 
    *1
    Battery Cover Lock Striker
    *2
    Button
    *a
    Push



5. INSTALL NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY
  1. Connect the connector.

  1. Engage the 2 clamps to install the No. 3 indoor electrical key antenna assembly.

    NOTICE:
    Be careful when installing the indoor electrical key antenna assembly. If the antenna is dropped, replace it with a new one.



6. INSTALL NO. 1 HYBRID BATTERY EXHAUST DUCT
  1. Install the No. 1 hybrid battery exhaust duct with the clip.



7. INSTALL REAR SEAT CUSHION LEG SUB-ASSEMBLY
  1. Temporarily install the rear seat cushion leg sub-assembly with the 4 bolts.



    A266710E01
  1. Tighten the bolt (A).

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Tighten the bolt (B).

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Tighten the 2 bolts (C).

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



8. INSTALL REAR SEAT CUSHION ASSEMBLY
  1. Place the rear seat cushion assembly in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.



    B296199
  1. Push out the seat belt buckles from the back of the rear seat cushion assembly so that they are positioned as shown in the illustration.



    B296198
  1. Engage the hook of the rear seat cushion assembly to the CRS anchor bracket.



    B296116
  1. Engage the 2 rear seat cushion lock hooks to install the rear seat cushion assembly as shown in the illustration.

  1. Confirm that the seat cushion is firmly installed.

    NOTICE:
    When installing the seat cushion, make sure that the seat belt buckles are not under the seat cushion.

  1. Engage the 2 clips.



9. INSTALL SERVICE PLUG GRIP
(Click here)