Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM

DTC    C1511/11    Torque Sensor 1 Malfunction

DTC    C1512/12    Torque Sensor Circuit Malfunction

DTC    C1513/13    Torque Sensor Circuit Malfunction

DTC    C1514/14    Torque Sensor Power Source Circuit Malfunction

DTC    C1517/17    Torque Sensor Hold Malfunction

for Preparation Click here


DESCRIPTION

The torque sensor converts the rotation torque received from the steering wheel into electric signals and sends them to the power steering ECU assembly.

DTC No.
DTC Detection Condition
Trouble Area
C1511/11
Torque sensor malfunction
  1. Torque sensor (built into electric power steering column sub-assembly)
  2. Power steering ECU assembly
C1512/12
C1513/13
C1514/14
C1517/17

WIRING DIAGRAM


C245322E08


INSPECTION PROCEDURE

NOTICE:
  1. If the power steering ECU assembly has been replaced with a new one, perform assist map writing and torque sensor zero point calibration (Click here).
  2. If the electric power steering column sub-assembly has been replaced with a new one, perform torque sensor zero point calibration after performing the initialization of the torque sensor zero point value (Click here).

1.CHECK CONNECTOR CONNECTION CONDITION
  1. Check the connection condition of the torque sensor connector.

    OK:
    Torque sensor connector is securely connected to the power steering ECU assembly.



NG
CONNECT CONNECTOR
OK


2.CHECK POWER STEERING ECU ASSEMBLY (TRQV VOLTAGE)
C238943E05
  1. Turn the ignition switch to ON (READY).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    z7-8 (TRQV) - body ground
    Ignition switch ON (READY)
    4.5 to 5.5 V

    Text in Illustration 
    *a
    Component with harness connected
    (Power Steering ECU Assembly)



NG
REPLACE POWER STEERING ECU ASSEMBLY (Click here)
OK


3.CHECK POWER STEERING ECU ASSEMBLY (TRQ1, TRQ2 VOLTAGE)


    C238943E06
  1. Turn the ignition switch on to ON (READY).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    (Steering Wheel Position)
    Specified Condition
    z7-9 (TRQ1) - Body ground
    Ignition switch ON (READY)
    (Center position)
    2.3 to 2.7 V
    z7-1 (TRQ2) - Body ground
    Ignition switch ON (READY)
    (Center position)
    2.3 to 2.7 V
    z7-9 (TRQ1) - Body ground
    Ignition switch ON (READY)
    (Turned to right)
    2.5 to 3.8 V
    z7-1 (TRQ2) - Body ground
    Ignition switch ON (READY)
    (Turned to right)
    1.2 to 2.5 V
    z7-9 (TRQ1) - Body ground
    Ignition switch ON (READY)
    (Turned to left)
    1.2 to 2.5 V
    z7-1 (TRQ2) - Body ground
    Ignition switch ON (READY)
    (Turned to left)
    2.5 to 3.8 V

  1. Under each condition, measure the voltage at terminals TRQ1 and TRQ2, and calculate the sum.

    Standard Voltage:
    Inspection Item
    Condition (Steering Wheel Position)
    Specified Condition
    Sum of voltage between z7-9 (TRQ1) and body ground and voltage between z7-1 (TRQ2) and body ground
    Ignition switch ON (READY)
    Steering wheel not being turned (without load)
    Between 4.75 V and 5.25 V
    Ignition switch ON (READY)
    Steering wheel being turned to the right with vehicle stopped
    Ignition switch ON (READY)
    Steering wheel being turned to the left with vehicle stopped

    Text in Illustration 
    *a
    Component with harness connected
    (Power Steering ECU Assembly)



NG
REPLACE ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY (Click here)
OK

REPLACE POWER STEERING ECU ASSEMBLY (Click here)