Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY

FRONT SEAT OUTER BELT ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSPECT FRONT SEAT OUTER BELT ASSEMBLY


    B131510E09
  1. Before installing the front seat outer belt assembly, check the ELR function.

    NOTICE:
    Do not disassemble the retractor.


    1. When the inclination of the retractor is 15° or less, check that the belt can be pulled from the retractor. When the inclination of the retractor is over 45°, check that the belt locks.
      Text in Illustration 
      *1
      Retractor
      *a
      Unlocked
      *b
      Locked
      *c
      45°
      If the result is not as specified, replace the front seat outer belt assembly.



2. INSTALL FRONT SEAT OUTER BELT ASSEMBLY


    B307779E01
  1. Engage the 2 hooks and temporarily install the front seat outer belt assembly with the 2 bolts.

  1. Tighten bolt A and then bolt B.

    Torque:
    4.9 N*m{ 50 kgf*cm , 43 in.*lbf } for bolt A
    42 N*m{ 428 kgf*cm , 31 ft.*lbf } for bolt B



    B307777E01
  1. Connect the pretensioner connector.
    Text in Illustration 
    *1
    Locking Button

  1. Lock the locking button.

    NOTICE:
    Securely lock the locking button.

  1. Connect the shoulder anchor of the front seat outer belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Temporarily install the floor anchor of the front seat outer belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Check that the ELR locks.

    NOTICE:
    The check should be performed with the front seat outer belt installed.


    1. With the belt installed, check that the belt locks when it is pulled out quickly.

      NOTICE:
      If the operation is not as specified, replace the front seat outer belt.



3. INSTALL CENTER PILLAR UPPER GARNISH
  1. Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar upper garnish LH.

  1. Engage the clip.

  1. Install the center pillar upper garnish LH with the 2 screws.



4. INSTALL CENTER PILLAR LOWER GARNISH
  1. Engage the 4 claws and 2 clips to install the center pillar lower garnish LH.



5. CONNECT FRONT SEAT OUTER BELT ASSEMBLY
  1. Install the floor anchor of the front seat outer belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



6. INSTALL LAP BELT OUTER ANCHOR COVER
  1. Engage the 3 claws and install the lap belt outer anchor cover.



7. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP


    B299875E01
  1. Align the alignment mark (White) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.
    Text in Illustration 
    *a
    Alignment Mark (White)
    *b
    Flange Position

    NOTICE:
    After installation, check that the corners fit correctly.



8. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP


    B299871E01
  1. Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
    Text in Illustration 
    *a
    Alignment Mark (Yellow)
    *b
    Flange Position

    NOTICE:
    After installation, check that the corners fit correctly.



9. INSTALL REAR DOOR SCUFF PLATE
  1. Engage the guide and the 5 claws to install the rear door scuff plate.



10. INSTALL FRONT FLOOR COVER LH (for LH Side)
  1. Engage the 3 guides.



    B301490E01
  1. Engage the 3 clips <B> to install the front floor cover LH.

  1. Install the 2 clips <A>.



11. INSTALL FRONT DOOR SCUFF PLATE
  1. Engage the 8 claws to install the front door scuff plate.



12. CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL


13. INSTALL FRONT FLOOR COVER RH
  1. Engage the 3 guides.



    B301488E01
  1. Engage the 3 clips <B> to install the front floor cover RH.

  1. Install the 2 clips <A>.



14. INSPECT SRS WARNING LIGHT
(Click here)