Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Smart Key System)

DTC    B1242    Wireless Door Lock Tuner Circuit Malfunction

for Preparation Click here


DESCRIPTION

The door control and tire pressure monitoring system receiver assembly is used to receive radio waves relating to the entry functions of the electrical key transmitter sub-assembly. The certification ECU (smart key ECU assembly) decodes the requested electrical key transmitter sub-assembly by identifying a key code based on the radio waves received via the door control and tire pressure monitoring system receiver assembly. The door control and tire pressure monitoring system receiver assembly receives a signal from the electrical key transmitter sub-assembly and sends signals to the main body ECU (multiplex network body ECU) through the certification ECU (smart key ECU assembly). The certification ECU (smart key ECU assembly) then sends a command, according to the requested operation, to each ECU (ex. if door lock operation is requested, the certification ECU (smart key ECU assembly) sends a door lock command to the main body ECU (multiplex network body ECU)).

DTC No.
DTC Detection Condition
Trouble Area
B1242
  1. Short in RDAM to ground between the certification ECU (smart key ECU assembly) and the door control and tire pressure monitoring system receiver assembly.
  2. Short in RDAM to ground when RCO (5 V) output from the ECU is off.
  1. Wire harness or connector
  2. door control and tire pressure monitoring system receiver assembly
  3. Certification ECU (Smart key ECU assembly)

WIRING DIAGRAM


B281122E08


INSPECTION PROCEDURE

NOTICE:
  1. When replacing or inspecting the door control and tire pressure monitoring system receiver assembly and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the door control and tire pressure monitoring system receiver assembly, smart and wireless function performance may be affected.
  2. Before performing the inspection, check that there are no problems related to the CAN communication system (Click here).
  3. When replacing the door control and tire pressure monitoring system receiver assembly, read the transmitter IDs (tire pressure warning system) stored in the old ECU using the Techstream and write them down before removal (Click here).
  4. It is necessary to perform initialization (Click here) after registration (Click here) of the transmitter IDs into the door control and tire pressure monitoring system receiver assembly if the door control and tire pressure monitoring system receiver assembly has been replaced.
  5. This DTC is not detected within 10 seconds after the power switch is turned to off from on (IG).

1.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


    B274834E09
  1. Disconnect the M17 door control and tire pressure monitoring system receiver assembly connector.

  1. Measure the resistance and voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    M17-10 (+5) - M17-12 (GND)
    Power switch off, all doors closed and electrical key transmitter sub-assembly lock/unlock switch not pressed → electrical key transmitter sub-assembly lock/unlock switch pressed
    Below 1 V → 4.5 to 5.5 V
    (Pulse generation)
    M17-9 (DATA) - M17-12 (GND)
    Power switch off, all doors closed and electrical key transmitter sub-assembly lock/unlock switch not pressed → electrical key transmitter sub-assembly lock/unlock switch pressed → electrical key transmitter sub-assembly lock/unlock switch released
    Below 1 V → 11 to 14 V → Below 1 V

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M17-12 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to door control and tire pressure monitoring system receiver assembly)



NG
Go to step 2
OK

REPLACE DOOR CONTROL AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY (Click here)  

2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
  1. Disconnect the certification ECU (smart key ECU assembly) connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G53-7 (CSEL) - M17-6 (CSEL)
    Always
    Below 1 Ω
    G53-6 (RDAM) - M17-9 (DATA)
    Always
    Below 1 Ω
    G53-15 (RCO) - M17-10 (+5)
    Always
    Below 1 Ω
    G55-1 (E) - Body ground
    Always
    Below 1 Ω
    M17-12 (GND) - Body ground
    Always
    Below 1 Ω
    G53-7 (CSEL) or M17-6 (CSEL) - Body ground
    Always
    10 kΩ or higher
    G53-6 (RDAM) or M17-9 (DATA) - Body ground
    Always
    10 kΩ or higher
    G53-15 (RCO) or M17-10 (+5) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (Click here)