Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR

REAR DOOR > DISASSEMBLY

for Preparation Click here


HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The procedure described below is for the LH side.



1. PRECAUTION (w/ Power Window)

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work (Click here).



2. REMOVE FRONT FLOOR COVER RH (w/ Power Window)


    B301488E01
  1. Using a clip remover, remove the 2 clips <A>.

  1. Disengage the 3 clips <B>.



    B301489
  1. Disengage the 3 guides and remove the front floor cover RH.



3. DISCONNECT CABLE FROM AUXILIARY BATTERY NEGATIVE TERMINAL (w/ Power Window)

CAUTION:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here)



4. REMOVE REAR DOOR FRAME GARNISH


    B307128
  1. Disengage the 2 clips and 3 claws.

  1. Disengage the guide and remove the rear door frame garnish.



5. REMOVE REAR DOOR ARMREST BASE UPPER PANEL (w/o Power Window)


    B307130
  1. Disengage the 5 claws and 2 guides and remove the rear door armrest base upper panel.



6. REMOVE REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)


    B307131E01
  1. Apply protective tape to the area shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape

  1. Insert a clip remover between the plate and front door trim board.

  1. Turn the handle with the clip remover inserted, as shown in the illustration.

  1. Remove the rear door window regulator handle assembly and clip.



    B307132
  1. Remove the plate.



7. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL (w/ Power Window)


    B307129
  1. Disengage the 8 claws and 3 guides.

  1. Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.



8. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    B307133E02
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and open the cover.
    Text in Illustration 
    *1
    Protective Tape



    B307134
  1. Remove the 3 screws.



    B308235
  1. Remove the clip.



  1. Pull the rear door trim board sub-assembly at each position indicated in the illustration and disengage the 6 clips (A) in the order shown in the illustration.


    B322064E01

    NOTICE:
    Do not apply excessive force when pulling the rear door trim board sub-assembly.

  1. Using a moulding remover, disengage the clip (B).
    Text in Illustration 
    *1
    Moulding Remover



    B307135E01
  1. Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly and remove the rear door trim board.
    Text in Illustration 
    *1
    Rear Door Inside Locking Cable Assembly
    *2
    Rear Door Lock Remote Control Cable Assembly



9. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


    B307136
  1. Disengage the 4 guides and remove the rear door inside handle sub-assembly.



10. REMOVE REAR DOOR GLASS INNER WEATHERSTRIP


    B307137
  1. Disengage the 5 claws and remove the rear door glass inner weatherstrip as shown in the illustration.



11. REMOVE REAR DOOR SPEAKER COVER (w/o Rear Speaker)


    B307138
  1. Remove the rear door speaker cover.

    NOTICE:
    Remove any tape remaining on the door side.



12. REMOVE REAR SPEAKER ASSEMBLY (w/ Rear Speaker)


    E237145
  1. Disconnect the connector.



    E237146
  1. Using a drill bit with a diameter of less than 5 mm (0.197 in.), drill out the 3 rivet heads and remove the rear speaker assembly.

    NOTICE:
    1. Do not touch the cone part of the speaker.
    2. Do not drill the rivet at an angle as this will cause damage to the drill and drill hole. Line up the drill and rivet, and carefully drill out the rivet head.
    3. Be careful as the cut rivet will be very hot.

  1. Continue drilling and push out the remaining rivet fragments.

  1. Using a vacuum cleaner, remove the rivet fragments and shavings from the inside of the door.



13. REMOVE REAR DOOR SERVICE HOLE COVER


    B307139
  1. Remove the rear door service hole cover.

    NOTICE:
    Remove any tape remaining on the door side.



14. REMOVE REAR DOOR INSIDE PANEL NO. 1 BRACKET


    B307140
  1. Remove the 2 bolts and disengage the guide to remove the rear door inside panel No. 1 bracket.



15. REMOVE REAR DOOR CHECK ASSEMBLY


    B307141
  1. Remove the 3 bolts and rear door check assembly.



16. REMOVE REAR DOOR WEATHERSTRIP


    B307142E01
  1. Using a clip remover, disengage the 30 clips.
    Text in Illustration 
    *1
    Double-sided Tape

  1. Remove the rear door weatherstrip.



17. REMOVE REAR DOOR GLASS RUN


    B307143
  1. Remove the rear door glass run.



18. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


    B307144
  1. Remove the 2 bolts and screw, and rear door window division bar sub-assembly.



19. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


    B307145E02
  1. Slide the lower section of the rear door glass and disengage the rear door glass from the rear window regulator sub-assembly.

  1. Remove the rear door glass sub-assembly as indicated by the arrows in the order shown in the illustration.

    NOTICE:
    Do not damage the rear door glass.



20. REMOVE REAR DOOR GLASS CHANNEL SUB-ASSEMBLY


    B307146E01
  1. Using a screwdriver with its tip wrapped in protective tape, remove the rear door glass channel sub-assembly.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Do not damage the rear door glass.



21. REMOVE REAR DOOR GLASS CHANNEL FILLER
  1. Remove the rear door glass channel filler.



22. REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY (w/o Power Window)


    B307147
  1. Remove the 3 bolts and rear door window regulator assembly.

    NOTICE:
    Do not drop or damage the window regulator when removing the bolts.



23. REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY (w/ Power Window)


    B307148E01
  1. Disconnect the connector.
    Text in Illustration 
    *1
    Temporary Bolt

  1. Loosen the temporary bolt.

    NOTICE:
    Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator may fall and cause damage.

  1. Remove the 3 bolts and rear door window regulator assembly.

  1. Remove the temporary bolt from the rear door window regulator assembly.



24. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY (w/ Power Window)


    B307149
  1. Using a T25 "TORX" socket wrench, remove the 3 screws and power window regulator motor assembly.



25. REMOVE REAR DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY


    B298003E01
  1. Apply protective tape to the door panel in the area around the rear door glass outer weatherstrip assembly.
    Text in Illustration 
    *1
    Protective Tape



    B298001E01
  1. Using a screwdriver with the tip wrapped with protective tape, disengage the 4 claws.
    Text in Illustration 
    *1
    Protective Tape

  1. Disengage the guide and remove the rear door glass outer weatherstrip assembly.



26. REMOVE REAR DOOR QUARTER WINDOW GLASS


    B307150
  1. Slide the rear door quarter window glass as shown in the illustration and remove the rear door quarter window glass with rear door quarter window weatherstrip.



27. REMOVE REAR DOOR STIFFENER CUSHION


    B301504E01
  1. Remove the 2 bolts.
    Text in Illustration 
    *1
    Double-sided Tape

  1. Disengage the 2 guides and remove the rear door stiffener cushion.



28. REMOVE REAR DOOR LOCK ASSEMBLY


    B307151
  1. Remove the rear door lock child protection cover.



    B307152E01
  1. Disconnect the connector.

  1. Using a T30 "TORX" socket wrench, remove the 3 screws.

  1. Move the rear door lock assembly downward and pull the release plate out of the rear door outside handle frame.
    Text in Illustration 
    *1
    Release Plate



  1. When reusing the rear door lock assembly:



      B307153
    1. Remove the door lock wiring harness seal from the rear door lock assembly.



29. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    B307154
  1. Using a screwdriver, disengage the claw as shown in the illustration.



    B307155
  1. Remove the rear door lock remote control cable assembly as shown in the illustration.



30. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY


    B307156
  1. Using a screwdriver, disengage the 3 claws as shown in the illustration.



    B307157
  1. Remove the rear door inside locking cable assembly as shown in the illustration.



31. REMOVE REAR DOOR OUTSIDE HANDLE COVER


    B307158
  1. Using a "TORX" socket wrench T30, loosen the screw.

    HINT:
    The screw cannot be removed because it is integrated into the rear door outside handle frame sub-assembly.

  1. Disengage the claw and remove the rear door outside handle cover.



32. REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY


    B307159
  1. Remove the rear door outside handle assembly as shown in the illustration.



33. REMOVE REAR DOOR OUTSIDE HANDLE FRONT PAD


    B307160
  1. Disengage the 3 claws to remove the rear door outside handle front pad.



34. REMOVE REAR DOOR OUTSIDE HANDLE REAR PAD


    B307161
  1. Disengage the 2 claws to remove the rear door outside handle rear pad.



35. REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY


    B307162E01
  1. Using a T30 "TORX" socket wrench, loosen the screw.
    Text in Illustration 
    *a
    Outside
    *b
    Inside

  1. Slide the rear door outside handle frame subassembly to disengage the door handle nut and claw of the rear door outside handle frame subassembly, and then remove the rear door outside handle frame sub-assembly.



36. REMOVE NO. 2 BLACK OUT TAPE
  1. Using a heat light, heat the No. 2 black out tape and vehicle body.
    Heating Temperature 
    Item
    Temperature
    No. 2 Black Out Tape and Vehicle Body
    40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.



    B298011
  1. Pull back on one of the ends of the No. 2 black out tape to remove it.

    HINT:
    When pulling on the stripe, pull it parallel to the body.