REAR DOOR > REASSEMBLY |
| 1. REPAIR INSTRUCTION |
Clean the vehicle body surface.
Using a heat light, heat the vehicle body surface.
| Item | Temperature |
| Vehicle Body | 40 to 60°C (104 to 140°F) |
Wipe off any tape adhesive residue with cleaner.
Installation temperature
When the ambient temperature is below 15°C (59°F), perform the installation procedure after warming the vehicle body surface (installation surface of the door frame) and tape up to between 20 and 30°C (68 and 86°F) using a heat light. When the ambient temperature is above 35°C (95°F), cool the vehicle body surface (installation surface of the door frame) and tape down to between 20 and 30°C (68 and 86°F) prior to installation.
Before installation
Remove any coating roughness or dirt on and around the vehicle body surface where the tape will be installed (installation surface of the door frame). If any roughness or dirt remains when pressing the tape onto the surface, air will be trapped under the tape and result in a poor appearance.
Key points for handling the tape
The tape bends and rolls up easily. Store the tape between flat pieces of cardboard or other similar objects and keep it dry and flat.
Key points for installation of the tape (how to use a squeegee and installation procedure for flat surfaces)
To avoid air bubbles, slightly raise the part of the tape that is going to be applied so that its adhesive surface does not touch the vehicle body while applying the tape. Tilt the squeegee at 40 to 50° (pressing forward) or 30 to 45° (pulling) to the vehicle body surface and press the tape onto the vehicle body surface with a force of 20 to 30 N (2 to 3 kgf, 4.5 to 6.7 lbf) at a constant slow speed of 3 to 7 cm (1.18 to 2.76 in.) per second.

| *A | Pressing Forward | *B | Pulling |
| *1 | Non-padded Side | *2 | Padded Side |
| *3 | Squeegee | *4 | Black Out Tape |
| *5 | Release Paper | - | - |
| *a | Side View | - | - |
| Area | Measurement |
| A | 10 to 20 mm (0.393 to 0.787 in.) |
| B | 30 to 70 mm/sec. (1.18 to 2.76 in./sec.) |
| C | 40 to 50° (for pressing forward) |
| D | 30 to 45° (for pulling) |
Key points for installation of the tape (how to use a squeegee and installation procedure for hemmed surfaces)
![]() |
If it is difficult to apply the tape, install it in several steps as shown in the illustration. Use your fingers or the padded surface of a squeegee to slowly apply the tape to the hem of the vehicle, especially for a small hem.
| *1 | Squeegee |
| *2 | Hem |
| *a | First |
| *b | Second |
| *c | Third |
Key points for installation of the tape (how to use a squeegee and installation procedure for corners)
Remove the release paper and apply the tape carefully with your fingers.
Before applying the tape to each corner, heat the tape using a heat light and gradually apply it, avoiding wrinkles on the tape to achieve a neat finish.
Check after installation
After completing the application, check if the tape is applied neatly. If the tape is not applied neatly, reapply using new tape.
| 2. INSTALL NO. 2 BLACK OUT TAPE |
![]() |
Remove the portion of the new No. 2 black out tape at the perforation as shown in the illustration.
| *A | LH Side |
| *B | RH Side |
| *a | Perforation |
| *b | Remove |
| *c | Triangle |
Apply the new No. 2 black out tape to the positions shown in the illustration.

| *1 | Edge of curved surface | - | - |
| Dimension | Measurement |
| a | 3.0 mm (0.118 in.) |
| b | 3.0 mm (0.118 in.) |
| c | 2.0 mm (0.0787 in.) |
| d | 1.0 mm (0.0394 in.) |
| e | -1.0 to 1.0 mm (-0.0394 to 0.0394 in.) |
| 3. INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY |
Apply MP grease to the sliding parts of the rear door outside handle frame sub-assembly.
![]() |
Engage the door handle nut and claw.
| *a | Outside |
| *b | Inside |
Using a T30 "TORX" socket wrench, install the rear door outside handle frame sub-assembly with the screw.
| 4. INSTALL REAR DOOR OUTSIDE HANDLE REAR PAD |
![]() |
Engage the 2 claws and install the rear door outside handle rear pad.
| 5. INSTALL REAR DOOR OUTSIDE HANDLE FRONT PAD |
![]() |
Engage the 3 claws to install the rear door outside handle front pad.
| 6. INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY |
![]() |
Insert the front end of the rear door outside handle assembly into the rear door outside handle frame.
Insert the rear end of the rear door outside handle assembly into the rear door outside handle frame. Next, slide the rear door outside handle assembly toward the front of the vehicle to install it.
| 7. INSTALL REAR DOOR OUTSIDE HANDLE COVER |
![]() |
Engage the claw to temporary install the rear door outside handle cover.
Using a T30 "TORX" socket wrench, install the rear door outside handle cover with the screw.
| 8. INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY |
![]() |
Install the rear door inside locking cable assembly as shown in the illustration.
![]() |
Engage the 3 claws as shown in the illustration.
| 9. INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY |
![]() |
Install the rear door lock remote control cable assembly as shown in the illustration.
![]() |
Engage the claw as shown in the illustration.
| 10. INSTALL REAR DOOR LOCK ASSEMBLY |
Apply MP grease to the sliding parts of the rear door lock assembly.
When reusing the rear door lock assembly:
![]() |
Install a new door lock wiring harness seal to the rear door lock assembly.
![]() |
Insert the rear door lock assembly to the rear door outside handle release plate, and set it to the rear door panel.
| *1 | Release Plate |
Using a T30 "TORX" socket wrench, install the rear door lock assembly with the 3 screws.
Connect the connector.
![]() |
Install the rear door lock child protection cover.
| 11. INSTALL REAR DOOR STIFFENER CUSHION |
Clean the rear door panel sub-assembly.
![]() |
Engage the 2 guides.
| *1 | Double-sided Tape |
Install a new rear door stiffener cushion with the 2 bolts.
| 12. INSTALL REAR DOOR QUARTER WINDOW GLASS |
Install the rear door quarter window weatherstrip to the rear door quarter window glass.
![]() |
Install the rear door quarter window glass with the rear door quarter window weatherstrip as shown in the illustration.
| 13. INSTALL REAR DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY |
![]() |
Engage the guide and 4 claws to install the rear door glass outer weatherstrip assembly.
| 14. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY (w/ Power Window) |
![]() |
Using a T25 "TORX" socket wrench, install the power window regulator motor assembly with the 3 screws.
| 15. INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY (w/o Power Window) |
Apply MP grease to the sliding parts of the rear door power window regulator assembly.
![]() |
Install the rear door window regulator assembly with the 3 bolts in the order shown in the illustration.
| 16. INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY (w/ Power Window) |
Apply MP grease to the sliding parts of the rear door window regulator assembly.
Install the temporary bolt to the rear door window regulator assembly.
![]() |
Temporarily install the rear door window regulator assembly.
| *1 | Temporary Bolt |
Tighten the temporary bolt and 3 bolts to install the rear door window regulator assembly in the order shown in the illustration.
Connect the connector.
| 17. INSTALL REAR DOOR GLASS CHANNEL FILLER |
Apply soapy water to a new rear door glass channel filler.
![]() |
Install the new rear door glass channel filler as shown in the illustration.
| *a | Front Side |
| *b | Rear Side |
| *c | Edge of curved surface |
| Area | Measurement |
| A | 5.0 mm (0.197 in.) |
| B | 5.0 mm (0.197 in.) |
| 18. INSTALL REAR DOOR GLASS CHANNEL SUB-ASSEMBLY |
Apply soapy water to a rear door glass channel.
![]() |
Using a plastic-faced hammer, tap the channel onto the glass to install the glass channel sub-assembly.
| *a | Front Side |
| *b | Rear Side |
| *c | Edge of curved surface |
| Area | Measurement |
| A | 5.0 mm (0.197 in.) |
| B | 5.0 mm (0.197 in.) |
| 19. INSTALL REAR DOOR GLASS SUB-ASSEMBLY |
![]() |
Insert the rear door glass as indicated by the arrows in the order shown in the illustration.
Slide the lower section of the rear door glass sub-assembly and engage the rear door glass sub-assembly to the rear door window regulator assembly.
| 20. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY |
![]() |
Temporary install the rear door window division bar sub-assembly with the 2 bolts.
Install the rear door window division bar sub-assembly with the 2 bolts and screw.
| 21. INSTALL REAR DOOR GLASS RUN |
![]() |
Install the rear door glass run.
| 22. INSTALL REAR DOOR WEATHERSTRIP |
Clean the rear door panel sub-assembly.
![]() |
Engage the 30 clips to install a new front door weatherstrip.
| *1 | Double-sided tape |
| 23. INSTALL REAR DOOR CHECK ASSEMBLY |
Apply MP grease to the sliding areas of the rear door check assembly.
![]() |
Apply adhesive to the threads of the bolt (A).
Install the rear door check assembly with the 3 bolts.
| 24. INSTALL REAR DOOR INSIDE PANEL NO. 1 BRACKET |
![]() |
Engage the guide and install the rear door inside panel No. 1 bracket with the 2 bolts.
| 25. INSTALL REAR DOOR SERVICE HOLE COVER |
Apply butyl tape to the rear door panel.
Pass the rear door lock remote control cable, rear door inside locking cable and each connector through a new rear door service hole cover.
![]() |
Attach the rear door service hole cover according to the reference points on the rear door panel.
| *a | Reference Point |
| 26. INSTALL REAR DOOR SPEAKER COVER (w/o Rear Speaker) |
![]() |
Attach a new rear door speaker cover according to the reference points on the rear door panel.
| *a | Reference Point |
| 27. INSTALL REAR SPEAKER ASSEMBLY (w/ Rear Speaker) |
Using an air riveter or a hand riveter, install the rear speaker assembly with 3 new rivets.

| *1 | Riveter | *2 | Mandrel |
| *a | INCORRECT | *b | CORRECT |
Connect the connector.
| 28. INSTALL REAR DOOR GLASS INNER WEATHERSTRIP |
![]() |
Engage the 5 claws to install the rear door glass inner weatherstrip as shown in the illustration.
| 29. INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY |
![]() |
Engage the 4 guides to install the rear door inside handle sub-assembly.
| 30. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY |
![]() |
Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly to the rear door inside handle.
| *1 | Rear Door Inside Locking Cable Assembly |
| *2 | Rear Door Lock Remote Control Cable Assembly |
![]() |
Install the clip.
![]() |
Engage the 7 clips.
![]() |
Install the rear door trim board sub-assembly with the 3 screws.
![]() |
Engage the claw and close the cover.
| 31. INSTALL REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window) |
![]() |
Install the window regulator handle plate.
| *a | Inside of Vehicle |
Install the clip to the rear door window regulator handle assembly.
Fully close the rear door window.
![]() |
Install the rear door window regulator handle with the clip at the angle shown in the illustration.
| *a | Assemble when fully closed |
| Area | Measurement |
| A | -30° to 30° |
| 32. INSTALL REAR DOOR ARMREST BASE UPPER PANEL (w/o Power Window) |
![]() |
Engage the 2 guides and 5 claws to install the rear door armrest base upper panel.
| 33. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL (w/ Power Window) |
Connect the connector.
![]() |
Engage the 3guides and 8 claws to install the rear power window regulator switch assembly with rear door armrest base panel.
| 34. INSTALL REAR DOOR FRAME GARNISH |
![]() |
Engage the guide.
Engage the 2 clips and 3 claws to install the rear door frame garnish.
| 35. CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL (w/ Power Window) |
| 36. INSTALL FRONT FLOOR COVER RH (w/ Power Window) |
Engage the 3 guides.
![]() |
Engage the 3 clips <B> to install the front floor cover RH.
Install the 2 clips <A>.
| 37. INSPECT POWER WINDOW OPERATION (w/ Power Window) |