DOOR CONTROL RECEIVER > INSTALLATION |
| 1. INSTALL DOOR CONTROL AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY |
Install the door control and tire pressure monitoring system receiver assembly with the bolt.
Connect the connector.
| 2. INSTALL ROOF SIDE INNER GARNISH LH |
Pass the floor anchor of the rear seat 3 point type outer belt assembly LH through the roof side inner garnish LH.
Engage the 5 clips to install the roof side inner garnish LH.
| 3. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (w/o Package Tray Trim) |
Engage the guide and 2 clips.

| *1 | Rear Seatback Hinge | - | - |
Install the deck trim side panel assembly LH with the 2 screws and 5 clips.
Turn the rear seatback hinge in the direction indicated by the arrow shown in the illustration.
| 4. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (w/ Package Tray Trim) |
Engage the guide, 4 claws and 4 clips.

| *1 | Rear Seatback Hinge | - | - |
Install the deck trim side panel assembly LH with the bolt and 2 screws.
Turn the rear seatback hinge in the direction indicated by the arrow shown in the illustration.
| 5. INSTALL REAR ABSORBER CAP LH (w/ Package Tray Trim) |
Engage the 2 guides and 2 claws to install the rear absorber cap LH.
| 6. INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY (w/ Package Tray Trim) |
Connect the connector.
![]() |
Engage the claw to install the No. 1 luggage compartment light assembly.
| 7. CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH |
Engage the 2 claws.
Install the floor anchor of the rear seat 3 point type outer belt assembly with the bolt.
| 8. INSTALL REAR DECK TRIM COVER |
Engage the 2 guides and 4 claws.
Install the rear deck trim cover with the 2 clips.
| 9. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim) |
Install the package tray trim panel assembly.
| 10. INSTALL SPARE WHEEL CUSHION |
Install the 2 spare wheel cushions.
| 11. INSTALL REAR FLOOR MAT ASSEMBLY |
Install the rear floor mat assembly.
| 12. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH |
![]() |
Align the alignment mark (White) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.
| *a | Alignment Mark (White) |
| *b | Flange Position |
| 13. INSTALL REAR DOOR SCUFF PLATE LH |
Engage the guide and the 5 claws to install the rear door scuff plate.
| 14. INSTALL REAR SEAT CUSHION ASSEMBLY (for Bench Type Seatback) |
Place the rear seat cushion assembly in the cabin.
![]() |
Push out the seat belt buckles from the back of the rear seat cushion assembly so that they are positioned as shown in the illustration.
![]() |
Engage the hook of the rear seat cushion assembly to the CRS anchor bracket.
![]() |
Engage the 2 rear seat cushion lock hooks to install the rear seat cushion assembly as shown in the illustration.
Confirm that the seat cushion is firmly installed.
Engage the 2 clips.
| 15. INSTALL REAR SEATBACK ASSEMBLY (for Bench Type Seatback) |
Place the rear seatback assembly in the cabin.
Install the rear seatback assembly with the 2 bolts.
Raise the rear seatback assembly.
| 16. INSTALL REAR SEAT CUSHION ASSEMBLY (for Separate Type Seatback) |
Place the rear seat cushion assembly in the cabin.
![]() |
Push out the seat belt buckles from the back of the rear seat cushion assembly so that they are positioned as shown in the illustration.
![]() |
Engage the hook of the rear seat cushion assembly to the CRS anchor bracket.
![]() |
Engage the 2 rear seat cushion lock hooks to install the rear seat cushion assembly as shown in the illustration.
Confirm that the seat cushion is firmly installed.
Engage the 2 clips.
| 17. INSTALL REAR SEATBACK ASSEMBLY LH (for Separate Type Seatback) |
Place the rear seatback assembly LH in the cabin.
Install the rear seatback assembly LH with the 2 bolts.
Raise the rear seatback assembly LH.
| 18. INSTALL FRONT CENTER FLOOR COVER |
Engage the 2 guides to install the front center floor cover.
Install the 3 clips.
| 19. INSTALL FRONT FLOOR COVER LH |
Engage the 3 guides.
![]() |
Engage the 3 clips <B> to install the front floor cover LH.
Install the 2 clips <A>.
| 20. INSTALL FRONT FLOOR COVER RH |
Engage the 3 guides.
![]() |
Engage the 3 clips <B> to install the front floor cover RH.
Install the 2 clips <A>.
| 21. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY |
| 22. INSTALL REAR SEAT HEADREST ASSEMBLY |
| 23. REGISTRATION OF RECOGNITION CODE (w/o Smart Key System) |
| 24. REGISTER TRANSMITTER ID |
| 25. INSPECT TIRE PRESSURE WARNING SYSTEM |
| 26. PERFORM INITIALIZATION |