FUEL LID LOCK CONTROL CABLE ASSEMBLY > INSTALLATION |
| 1. INSTALL FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY |
Engage the 4 clamps.
![]() |
Engage the 2 claws to install the fuel lid lock control cable sub-assembly.
| 2. INSTALL FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY |
Connect the fuel lid lock control cable.
![]() |
Engage the guide.
Install the fuel lid lock open lever sub-assembly with the screw.
| 3. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (w/o Package Tray Trim) |
Engage the guide and 2 clips.

| *1 | Rear Seatback Hinge | - | - |
Install the deck trim side panel assembly LH with the 2 screws and 5 clips.
Turn the rear seatback hinge in the direction indicated by the arrow shown in the illustration.
| 4. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (w/ Package Tray Trim) |
Engage the guide, 4 claws and 4 clips.

| *1 | Rear Seatback Hinge | - | - |
Install the deck trim side panel assembly LH with the bolt and 2 screws.
Turn the rear seatback hinge in the direction indicated by the arrow shown in the illustration.
| 5. INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY (w/ Package Tray Trim) |
Connect the connector.
![]() |
Engage the claw to install the No. 1 luggage compartment light assembly.
| 6. INSTALL REAR ABSORBER CAP LH (w/ Package Tray Trim) |
Engage the 2 guides and 2 claws to install the rear absorber cap LH.
| 7. INSTALL REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH |
Engage the 2 guides to install the rear seat 3 point type outer belt assembly.
Install the bolt.
Connect the shoulder anchor of the rear seat 3 point type outer belt assembly with the bolt.
| 8. INSTALL REAR DECK TRIM COVER |
Engage the 2 guides and 4 claws.
Install the rear deck trim cover with the 2 clips.
| 9. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim) |
Install the package tray trim panel assembly.
| 10. INSTALL SPARE WHEEL CUSHION |
Install the 2 spare wheel cushions.
| 11. INSTALL REAR FLOOR MAT ASSEMBLY |
Install the rear floor mat assembly.
| 12. INSTALL CENTER LOWER PILLAR GARNISH LH |
Engage the 4 claws and 2 clips to install the center pillar lower garnish LH.
| 13. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH |
![]() |
Align the alignment mark (White) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.
| *a | Alignment Mark (White) |
| *b | Flange Position |
| 14. INSTALL REAR DOOR SCUFF PLATE LH |
Engage the guide and the 5 claws to install the rear door scuff plate.
| 15. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
![]() |
Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
| *a | Alignment Mark (Yellow) |
| *b | Flange Position |
| 16. INSTALL COWL SIDE TRIM BOARD LH |
Engage the clip.
Install the cowl side trim board with the clip.
| 17. INSTALL FRONT DOOR SCUFF PLATE LH |
Engage the 8 claws to install the front door scuff plate.
| 18. INSTALL REAR SEAT CUSHION ASSEMBLY (for Separate Type Seatback) |
Place the rear seat cushion assembly in the cabin.
![]() |
Push out the seat belt buckles from the back of the rear seat cushion assembly so that they are positioned as shown in the illustration.
![]() |
Engage the hook of the rear seat cushion assembly to the CRS anchor bracket.
![]() |
Engage the 2 rear seat cushion lock hooks to install the rear seat cushion assembly as shown in the illustration.
Confirm that the seat cushion is firmly installed.
Engage the 2 clips.
| 19. INSTALL REAR SEATBACK ASSEMBLY LH (for Separate Type Seatback) |
Place the rear seatback assembly LH in the cabin.
Install the rear seatback assembly LH with the 2 bolts.
Raise the rear seatback assembly LH.
| 20. INSTALL REAR SEAT CUSHION ASSEMBLY (for Bench Type Seatback) |
Place the rear seat cushion assembly in the cabin.
![]() |
Push out the seat belt buckles from the back of the rear seat cushion assembly so that they are positioned as shown in the illustration.
![]() |
Engage the hook of the rear seat cushion assembly to the CRS anchor bracket.
![]() |
Engage the 2 rear seat cushion lock hooks to install the rear seat cushion assembly as shown in the illustration.
Confirm that the seat cushion is firmly installed.
Engage the 2 clips.
| 21. INSTALL REAR SEATBACK ASSEMBLY (for Bench Type Seatback) |
Place the rear seatback assembly in the cabin.
Install the rear seatback assembly with the 2 bolts.
Raise the rear seatback assembly.
| 22. INSTALL FRONT CENTER FLOOR COVER |
Engage the 2 guides to install the front center floor cover.
Install the 3 clips.
| 23. INSTALL FRONT FLOOR COVER LH |
Engage the 3 guides.
![]() |
Engage the 3 clips <B> to install the front floor cover LH.
Install the 2 clips <A>.
| 24. INSTALL FRONT FLOOR COVER RH |
Engage the 3 guides.
![]() |
Engage the 3 clips <B> to install the front floor cover RH.
Install the 2 clips <A>.
| 25. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY |
| 26. INSTALL REAR SEAT HEADREST ASSEMBLY |
| 27. INSTALL FRONT SEAT ASSEMBLY LH |