Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/o Smart Key System)

ENGINE IMMOBILISER SYSTEM (w/o Smart Key System) > TERMINALS OF ECU

for Preparation Click here



CHECK TRANSPONDER KEY AMPLIFIER

B167608E17

  1. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item/DTC
    G47-7 (AGND) - Body ground
    -
    GR - Body ground
    Ground
    Always
    Below 1 Ω
    -
    G47-1 (VC5) - G47-7 (AGND)
    Input
    P - GR
    Transponder key amplifier power supply
    No key in ignition key cylinder
    Below 1 V
    -
    G47-4 (CODE) - G47-7 (AGND)
    Output
    G - GR
    Demodulated signal of key code data
    No key in ignition key cylinder
    Below 1 V
    -
    G47-5 (TXCT) - G47-7 (AGND)
    Input
    V - GR
    Key code output signal
    No key in ignition key cylinder
    Below 1 V
    -

  2. Check for pulses according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item/DTC
    G47-1 (VC5) - G47-7 (AGND)
    Input
    P - GR
    Transponder key amplifier power supply
    Key inserted in ignition key cylinder
    Pulse generation (See waveform 1)
    1. BCC Malfunction
    2. Abnormal Status
    3. Different Encrypt Code
    4. Different Serial Number
    (If immobiliser key code certification communication is not performed correctly, a malfunction may be indicated by one or more of the Data List items listed above)
    G47-4 (CODE) - G47-7 (AGND)
    Output
    G - GR
    Demodulated signal of key code data
    Key inserted in ignition key cylinder
    Pulse generation (See waveform 2)
    G47-5 (TXCT) - G47-7 (AGND)
    Input
    V - GR
    Key code output signal
    Key inserted in ignition key cylinder
    Pulse generation (See waveform 3)



  3. Inspect using an oscilloscope.

    NOTICE:
    The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.




      B287844E04
    1. Waveform 1 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      G47-1 (VC5) - G47-7 (AGND)
      Tool Setting
      1 V/DIV., 20 ms./DIV.
      Condition
      Key inserted in ignition key cylinder



    2. B287845E04
    3. Waveform 2 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      G47-4 (CODE) - G47-7 (AGND)
      Tool Setting
      1 V/DIV., 20 ms./DIV.
      Condition
      Key inserted in ignition key cylinder



    4. B287846E06
    5. Waveform 3 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      G47-5 (TXCT) - G47-7 (AGND)
      Tool Setting
      1 V/DIV., 20 ms./DIV.
      Condition
      Key inserted in ignition key cylinder


CHECK TRANSPONDER KEY ECU ASSEMBLY

B271269E06

  1. Disconnect the G46 transponder key ECU assembly connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item/DTC
    G46-16 (GND) - Body ground
    -
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    -
    G46-1 (+B) - G46-16 (GND)
    Input
    BE - W-B
    Auxiliary battery
    Ignition switch off
    11 to 14 V
    +B
    G46-2 (IG) - G46-16 (GND)
    Input
    V - W-B
    Ignition switch
    Ignition switch off
    Below 1 V
    IG SW
    Ignition switch ON
    11 to 14 V
    G46-3 (KSW) - G46-16 (GND)
    Input
    BE - W-B
    Unlock warning switch
    No key in ignition key cylinder
    10 kΩ or higher
    Key SW/B2780
    Key inserted in ignition key cylinder
    Below 1 Ω

  3. Reconnect the G46 transponder key ECU connector.

  4. Measure the resistance and voltage, and check for pulses according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item/DTC
    G46-14 (VC5) - G46-16 (GND)
    Input
    P - W-B
    Transponder key amplifier power supply
    No key in ignition key cylinder
    Below 1 V
    1. BCC Malfunction
    2. Abnormal Status
    3. Different Encrypt Code
    4. Different Serial Number
    (If immobiliser key code certification communication is not performed correctly, a malfunction may be indicated by one or more of the Data List items listed above)
    Key inserted in ignition key cylinder
    Pulse generation (See waveform 1)
    G46-4 (TXCT) - G46-16 (GND)
    Input
    V - W-B
    Key code output signal
    No key in ignition key cylinder
    Below 1 V
    Key inserted in ignition key cylinder
    Pulse generation (See waveform 2)
    G46-15 (CODE) - G46-16 (GND)
    Output
    G - W-B
    Demodulated signal of key code data
    No key in ignition key cylinder
    Below 1 V
    Key inserted in ignition key cylinder
    Pulse generation (See waveform 3)
    G46-13 (EFIO) - G46-16 (GND)
    Input
    LG - W-B
    Power management control ECU output signal
    Ignition switch off
    Below 1 V
    E/G Start Permission
    Within 3 seconds after hybrid control system starts, or within 3 seconds after ignition switch first turned to ON after auxiliary battery disconnected and reconnected
    Pulse generation (See waveform 4)
    G46-12 (EFII) - G46-16 (GND)
    Output
    BE - W-B
    Power management control ECU input signal
    Ignition switch off
    11 to 14 V
    E/G Start Permission
    Within 3 seconds after hybrid control system starts, or within 3 seconds after ignition switch first turned to ON after auxiliary battery disconnected and reconnected
    Pulse generation (See waveform 5)
    G46-8 (IND) - G46-16 (GND)
    Output
    LG - W-B
    Security indicator light signal
    Engine immobiliser system set
    Pulse generation
    Immobiliser
    Engine immobiliser system unset
    Below 1 V
    G46-9 (D) - G46-16 (GND)
    Input/Output
    B - W-B
    Diagnosis tester communication
    Always
    Pulse generation
    -
    G46-5 (AGND) - Body ground
    -
    GR - Body ground
    Transponder key amplifier ground
    Always
    Below 1 Ω
    -



  5. Inspect using an oscilloscope.

    NOTICE:
    The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.




      B287844E05
    1. Waveform 1 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      G46-14 (VC5) - G46-16 (GND)
      Tool Setting
      1 V/DIV., 20 ms./DIV.
      Condition
      Key inserted in ignition key cylinder



    2. B287846E07
    3. Waveform 2 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      G46-4 (TXCT) - G46-16 (GND)
      Tool Setting
      1 V/DIV., 20 ms./DIV.
      Condition
      Key inserted in ignition key cylinder



    4. B287845E05
    5. Waveform 3 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      G46-15 (CODE) - G46-16 (GND)
      Tool Setting
      1 V/DIV., 20 ms./DIV.
      Condition
      Key inserted in ignition key cylinder



    6. Waveform 4 (Reference)


      B302042E01


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Measurement Condition 
      Item
      Content
      Tester Connection
      G46-13 (EFIO) - G46-16 (GND)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds after hybrid control system starts, or within 3 seconds after ignition switch first turned to ON after auxiliary battery disconnected and reconnected



    7. Waveform 5 (Reference)


      B302041E01


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Measurement Condition 
      Item
      Content
      Tester Connection
      G46-12 (EFII) - G46-16 (GND)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds after hybrid control system starts, or within 3 seconds after ignition switch first turned to ON after auxiliary battery disconnected and reconnected


CHECK POWER MANAGEMENT CONTROL ECU

B220221E04


Terminal No. (Symbol)
Input/Output
Wiring Color
Terminal Description
Condition
Specified Condition
Related Data List Item/DTC
A38-2 (+B2) - G57-5 (E01)
Input
L - W-B
IG power supply
Ignition switch ON
11 to 14 V
-
A39-5 (+B1) - G57-5 (E01)
Input
L - W-B
IG power supply
Ignition switch ON
11 to 14 V
-
A39-6 (MREL) - G57-5 (E01)
Input
BE - W-B
IG power supply
Ignition switch ON
11 to 14 V
-
G57-5 (E01) - Body ground
-
W-B - Body ground
Ground
Always
Below 1 Ω
-
G57-6 (E1) - Body ground
-
BR - Body ground
Ground
Always
Below 1 Ω
-
G58-5 (E02) - Body ground
-
W-B - Body ground
Ground
Always
Below 1 Ω
-
G58-20 (IMO) - G57-6 (E1)
Input
BE - BR
Transponder key ECU assembly communication input
Ignition switch off
11 to 14 V
E/G Start Permission
G58-20 (IMO) - G57-6 (E1)
Input
BE - BR
Transponder key ECU assembly communication input
Within 3 seconds after hybrid control system starts, or within 3 seconds after ignition switch first turned to ON after auxiliary battery disconnected and reconnected
Pulse generation
(See waveform 1)
E/G Start Permission
G58-21 (IMI) - G57-6 (E1)
Output
LG - BR
Transponder key ECU assembly communication output
Ignition switch off
Below 1 V
E/G Start Permission
G58-21 (IMI) - G57-6 (E1)
Output
LG - BR
Transponder key ECU assembly communication output
Within 3 seconds after hybrid control system starts, or within 3 seconds after ignition switch first turned to ON after auxiliary battery disconnected and reconnected
Pulse generation
(See waveform 2)
E/G Start Permission


  1. Inspect using an oscilloscope.



    1. Waveform 1 (Reference)


      B302041E01


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Measurement Condition 
      Item
      Content
      Tester Connection
      G58-20 (IMO) - G57-6 (E1)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds after hybrid control system starts, or within 3 seconds after ignition switch first turned to ON after auxiliary battery disconnected and reconnected



    2. Waveform 2 (Reference)


      B302042E01


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Measurement Condition 
      Item
      Content
      Tester Connection
      G58-21 (IMI) - G57-6 (E1)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds after hybrid control system starts, or within 3 seconds after ignition switch first turned to ON after auxiliary battery disconnected and reconnected