LIN COMMUNICATION SYSTEM > TERMINALS OF ECU |
| CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| MB-30 (BECU) - Body ground | - | Auxiliary battery power supply | Ignition switch off | 11 to 14 V |
| MB-32 (IG) - Body ground | - | IG power supply | Ignition switch ON (IG) | 11 to 14 V |
| MB-29 (ACC) - Body ground | - | ACC power supply | Ignition switch ACC | 11 to 14 V |
| MB-11 (GND1) - Body ground | - | Ground | Always | Below 1 Ω |
Reinstall the main body ECU (multiplex network body ECU) to the instrument panel junction block assembly.
Check for pulses according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| 3B-12 (LIN2) - 3B-8 (GND1) | B - W-B | LIN communication line | Ignition switch ON (IG) | Pulse generation |
| 3A-4 (LIN2) - 3B-8 (GND1)* | R - W-B | LIN communication line | Ignition switch ON (IG) | Pulse generation |
| CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door) |
Disconnect the J3 power window regulator motor assembly (for driver door) connector.

Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| J3-2 (B) - J3-1 (GND) | LA-G - LA | Auxiliary battery power supply | Ignition switch off | 11 to 14 V |
| J3-1 (GND) - Body ground | LA - Body ground | Ground | Always | Below 1 Ω |
Reconnect the J3 power window regulator motor assembly (for driver door) connector.
Check for pulses according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| J3-9 (LIN) - J3-1 (GND) | B - LA | LIN communication line | Ignition switch ON (IG) | Pulse generation |
| CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) (w/ Sliding Roof System) |
Disconnect the Q3 sliding roof ECU (sliding roof drive gear assembly) connector.

Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| Q3-8 (B) - Q3-12 (E) | B - W-B | Auxiliary battery power supply | Ignition switch off | 11 to 14 V |
| Q3-12 (E) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the Q3 sliding roof ECU (sliding roof drive gear assembly) connector.
Check for pulses according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| Q3-11 (MPX1) - Q3-12 (E) | BE - W-B | LIN communication line | Ignition switch ON (IG) | Pulse generation |
| CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Smart Key System) |
Disconnect the G54 and G55 certification ECU (smart key ECU assembly) connectors.

Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| G54-5 (+B) - G55-1 (E) | BE - W-B | Auxiliary battery power supply | Ignition switch off | 11 to 14 V |
| G55-1 (E) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the G55 and G54 certification ECU (smart key ECU assembly) connectors.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| G54-16 (IG) - G55-1 (E) | V - W-B | IG power supply | Ignition switch ON (IG) | 11 to 14 V |
| G54-16 (IG) - G55-1 (E) | V - W-B | IG power supply | Ignition switch off | Below 1 V |
| G54-12 (LIN) - G55-1 (E) | LG - W-B | LIN communication line | Ignition switch ON (IG) | Pulse generation |
| CHECK POWER MANAGEMENT CONTROL ECU (w/ Smart Key System) |
Disconnect the G57 and G58 power management control ECU connectors.

Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| G57-1 (AM22) - Body ground | B - Body ground | Auxiliary battery power supply | Ignition switch off | 11 to 14 V |
| G58-7 (AM21) - Body ground | B - Body ground | Auxiliary battery power supply | Ignition switch off | 11 to 14 V |
| G57-6 (E1) - Body ground | BR - Body ground | Ground | Always | Below 1 Ω |
Reconnect the G57 and G58 power management control ECU connectors.
Check for pulses according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| G58-11 (LIN2) - G57-6 (E1) | LG - BR | LIN communication line | Ignition switch ON (IG) | Pulse generation |
| CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) (w/ Smart Key System) |
![]() |
Disconnect the G50 steering lock ECU (steering lock actuator assembly) connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| G50-1 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| G50-7 (B) - Body ground | GR - Body ground | Auxiliary battery power supply | Ignition switch off | 11 to 14 V |
| G50-6 (IG2) - Body ground | SB - Body ground | IG power supply | Ignition switch ON (IG) | 11 to 14 V |
Reconnect the G50 steering lock ECU (steering lock actuator assembly) connector.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| G50-5 (LIN) - G50-1 (GND) | LG - W-B | LIN communication line | Ignition switch ON (IG) | Pulse generation |
| CHECK ID CODE BOX (IMMOBILISER CODE ECU) (w/ Smart Key System) |
Disconnect the G49 ID code box (immobiliser code ECU) connector.

Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| G49-1 (+B) - G49-5 (GND) | BE - W-B | Auxiliary battery power supply | Ignition switch off | 11 to 14 V |
| G49-5 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the G49 ID code box (immobiliser code ECU) connector.
Check for pulses according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| G49-2 (LIN1) - G49-5 (GND) | LG - W-B | LIN communication line | Ignition switch ON (IG) | Pulse generation |