Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR (for Front Door)

POWER WINDOW REGULATOR MOTOR (for Front Door) > INSTALLATION

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).



2. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY

NOTICE:
The regulator arm must be below the intermediate position when installing the power window regulator motor.



    B307091
  1. Using a T25 "TORX" socket wrench, install the power window regulator motor assembly with the 3 screws.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    HINT:
    A new front window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.



3. INSTALL FRONT DOOR WINDOW REGULATOR ASSEMBLY
  1. Apply MP grease to the sliding parts of the front door power window regulator assembly.

  1. Install the temporary bolt to the front door power window regulator assembly.



    B307122E01
  1. Temporarily install the front door power window regulator assembly.
    Text in Illustration 
    *1
    Temporary Bolt

  1. Tighten the temporary bolt and 5 bolts.

    HINT:
    Tighten the bolts in the order shown in the illustration.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.



4. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY
  1. Connect the cable to the negative (-) auxiliary battery terminal and power window regulator master switch assembly and move the front door glass subassembly so that the door glass bolts can be seen.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal and power window regulator master switch.



    B307123
  1. Insert the front door glass sub-assembly into the front door panel along the front door glass run as shown in the illustration.

    NOTICE:
    Do not damage the front door glass.



    B307088
  1. Install the front door glass sub-assembly with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    B307087
  1. Install the front door No. 2 service hole cover.



5. INSTALL FRONT DOOR SERVICE HOLE COVER
  1. Apply new butyl tape to the front door panel.

  1. Pass the front door lock remote control cable assembly and front door inside locking cable assembly through a new front door service hole cover.



    B307124E01
  1. Attach the front door service hole cover according to the reference points on the front door panel.
    Text in Illustration 
    *a
    Reference Point

    HINT:
    Securely install the front door service hole cover preventing wrinkles and air bubbles.

  1. Connect the earth wire with the bolt.

    Torque:
    8.4 N*m{ 85 kgf*cm , 74 in.*lbf }



6. INSTALL DOOR SIDE AIRBAG SENSOR
  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



  1. Before connecting the connector, check that the position of the white housing lock is correct as shown in the illustration.


    B296255E01


    Text in Illustration 
    *a
    Incorrect
    *b
    Correct

  1. Insert the pin (stopper) into the door hole and install the door side airbag sensor to the front door panel with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    NOTICE:
    1. If the door side airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
    2. When installing the door side airbag sensor, be careful that the SRS wiring does not interfere with or is not pinched between other parts.
    3. Make sure that the pin (stopper) is securely inserted into the door hole.
    4. Tighten the bolt while holding the door side airbag sensor because the door side airbag sensor pin (stopper) is easily damaged.



  1. Connect the connector to the door side airbag sensor.

    NOTICE:
    When connecting any airbag connector, take care not to damage the airbag wire harness.




    1. Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).


      H043305E12


      Text in Illustration 
      *1
      White Housing Lock
      *2
      Yellow CPA
      *a
      Connection is Completed
      -
      -

      HINT:
      When engaged, the white housing lock will slide. Be sure not to hold the white housing lock and part (A), as it may result in an insecure fit.

  1. Check that there is no looseness in the installation parts of the door side airbag sensor.



7. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY
  1. Install the front No. 2 speaker assembly with the 2 screws.

    NOTICE:
    Do not touch the cone part of the speaker.

  1. Connect the connector.



8. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    B307126E02
  1. Connect the front door lock remote control cable assembly and front door inside locking cable assembly to the front door inside handle sub-assembly.
    Text in Illustration 
    *1
    Front Door Inside Locking Cable Assembly
    *2
    Front Door Lock Remote Control Cable Assembly



    B307169
  1. Engage the 8 clips.



    B307081
  1. Install the front door trim board sub-assembly with the 3 screws.



    B307127
  1. Engage the claw and close the cover.



9. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)
  1. Connect the connector.



    B307078
  1. Engage the 4 guides and 10 claws to install power window regulator master switch assembly with front door armrest base panel.



10. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)
  1. Connect the connector.



    B307079
  1. Engage the 4 guides and 10 claws to install power window regulator switch assembly with front door armrest base panel.



11. CONNECT CABLE FROM AUXILIARY BATTERY NEGATIVE TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



12. INSTALL FRONT FLOOR COVER RH
  1. Engage the 3 guides.



    B301488E01
  1. Engage the 3 clips <B> to install the front floor cover RH.

  1. Install the 2 clips <A>.



13. INITIALIZE POWER WINDOW CONTROL SYSTEM
(Click here)


14. INSPECT POWER WINDOW OPERATION
(Click here)