Home › Vehicle Exterior › WINDOW / GLASS › WINDOW DEFOGGER SYSTEM

WINDOW DEFOGGER SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

B274525E13

  1. Disconnect the G34 air conditioning amplifier assembly connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G34-1 (IG+) - G34-14 (GND)
    V - W-B
    Ignition power supply
    Ignition switch ON (IG)
    11 to 14 V
    G34-1 (IG+) - G34-14 (GND)
    V - W-B
    Ignition power supply
    Ignition switch off
    Below 1 V
    G34-14 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    G34-21 (B) - G34-14 (GND)
    BE - W-B
    Auxiliary battery power supply
    Ignition switch off
    11 to 14 V
    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the G34 air conditioning amplifier assembly connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G34-37 (LIN1) - G34-14 (GND)
    LG - W-B
    LIN communication signal
    Ignition switch ON (IG)
    Pulse generation
    G34-38 (RDFG) - G34-14 (GND)
    B - W-B
    Rear window defogger signal
    Ignition switch ON (IG), rear window defogger switch OFF
    11 to 14 V
    G34-38 (RDFG) - G34-14 (GND)
    B - W-B
    Rear window defogger signal
    Ignition switch ON (IG), rear window defogger switch ON
    Below 1 V

    1. If the result is not as specified, the air conditioning amplifier assembly may be malfunctioning.


CHECK AIR CONDITIONING PANEL (HEATER CONTROL SWITCH BOARD)

E233187E02

  1. Disconnect the G33 air conditioning panel (heater control switch board) connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G33-5 (IG+) - G33-8 (GND)
    V - W-B
    Ignition power supply
    Ignition switch ON (IG)
    11 to 14 V
    G33-5 (IG+) - G33-8 (GND)
    V - W-B
    Ignition power supply
    Ignition switch off
    Below 1 V
    G33-8 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the G33 air conditioning panel (heater control switch board) connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G33-2 (LIN1) - G33-8 (GND)
    LG - W-B
    LIN communication signal
    Ignition switch ON (IG)
    Pulse generation

    1. If the result is not as specified, the air conditioning panel (heater control switch board) may be malfunctioning.