Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR DOOR BELT MOULDING

REAR DOOR BELT MOULDING > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for both the RH and LH side.
  2. The procedure described below is for the LH side.



1. INSTALL REAR DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY


    B298002
  1. Engage the guide and 4 claws to install the rear door glass outer weatherstrip assembly.



2. INSTALL REAR DOOR GLASS SUB-ASSEMBLY


    B307174E01
  1. Insert the rear door glass as indicated by the arrows in the order shown in the illustration.

    NOTICE:
    Do not damage the rear door glass.

  1. Slide the lower section of the rear door glass sub-assembly and engage the rear door glass sub-assembly to the rear door window regulator assembly.



3. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


    B307144
  1. Temporary install the rear door window division bar sub-assembly with the 2 bolts.

    NOTICE:
    Do not damage the rear door glass.

  1. Install the rear door window division bar sub-assembly with the 2 bolts and screw.



4. INSTALL REAR DOOR GLASS RUN


    B307143
  1. Install the rear door glass run.



5. INSTALL REAR DOOR WEATHERSTRIP
  1. Connect the upper part of the rear door weatherstrip.



6. INSTALL REAR DOOR INSIDE PANEL NO. 1 BRACKET


    B307140
  1. Engage the guide and install the rear door inside panel No. 1 bracket with the 2 bolts.



7. INSTALL REAR DOOR SERVICE HOLE COVER
  1. Apply butyl tape to the rear door panel.

  1. Pass the rear door lock remote control cable, rear door inside locking cable and each connector through a new rear door service hole cover.



    B307175E01
  1. Attach the rear door service hole cover according to the reference points on the rear door panel.
    Text in Illustration 
    *a
    Reference Point

    NOTICE:
    Securely install the rear door service hole cover preventing wrinkles and air bubbles.



8. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY


    B307178E01
  1. Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly to the rear door inside handle.
    Text in Illustration 
    *1
    Rear Door Inside Locking Cable Assembly
    *2
    Rear Door Lock Remote Control Cable Assembly



    B308235
  1. Install the clip.



    B307182
  1. Engage the 7 clips.



    B307134
  1. Install the rear door trim board sub-assembly with the 3 screws.



    B307179
  1. Engage the claw and close the cover.



9. INSTALL REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)


    B307180E01
  1. Install the window regulator handle plate.
    Text in Illustration 
    *a
    Inside of Vehicle

  1. Install the clip to the rear door window regulator handle assembly.

  1. Fully close the rear door window.



    B307181E01
  1. Install the rear door window regulator handle with the clip at the angle shown in the illustration.
    Text in Illustration 
    *a
    Assemble when fully closed
    Area
    Measurement
    A
    -30° to 30°



10. INSTALL REAR DOOR ARMREST BASE UPPER PANEL (w/o Power Window)


    B307130
  1. Engage the 2 guides and 5 claws to install the rear door armrest base upper panel.



11. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL (w/ Power Window)
  1. Connect the connector.



    B307129
  1. Engage the 3guides and 8 claws to install the rear power window regulator switch assembly with rear door armrest base panel.



12. INSTALL REAR DOOR FRAME GARNISH


    B307128
  1. Engage the guide.

  1. Engage the 2 clips and 3 claws to install the rear door frame garnish.



13. CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL (w/ Power Window)

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here)



14. INSTALL FRONT FLOOR COVER RH (w/ Power Window)
  1. Engage the 3 guides.



    B301488E01
  1. Engage the 3 clips <B> to install the front floor cover RH.

  1. Install the 2 clips <A>.



15. INSPECT POWER WINDOW OPERATION (w/ Power Window)
(Click here)