Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING

ROOF HEADLINING > REASSEMBLY

for Preparation Click here



1. INSTALL ROOM LIGHT BRACKET (w/ Sliding Roof)


    B301738E01
  1. Align the markings on the roof headlining with a new room light bracket and install the bracket using hot-melt glue as shown in the illustration.
    Text in Illustration 
    *1
    Hot-melt Glue
    *2
    Marking



2. INSTALL NO. 1 ROOF WIRE (w/o Sliding Roof)


  1. Align the positioning tape (Red) on the front part of the No. 1 roof wire with the front tab of the roof headlining.


    B300775E01


    Text in Illustration 
    *1
    Adhesive Tape
    *2
    Positioning Tape (Red)
    *3
    Positioning Tape (White)
    *4
    Marking

  1. Align the No. 1 roof wire positioning tape (White) with the markings of the roof headlining.

  1. Install the No. 1 roof wire onto the roof headlining with the adhesive tape.

    NOTICE:
    1. Apply the tape securely in place.
    2. Do not touch the adhesive surface when applying the tape to prevent adhesion failure.



3. INSTALL NO. 1 ROOF WIRE (w/ Sliding Roof)


  1. Align the positioning tape (Red) on the front part of the No. 1 roof wire with the front tab of the roof headlining.


    B300776E01


    Text in Illustration 
    *1
    Adhesive Tape
    *2
    Positioning Tape (Red)
    *3
    Positioning Tape (White)
    *4
    Marking

  1. Align the No. 1 roof wire positioning tape (White) with the markings of the roof headlining.

  1. Install the No. 1 roof wire onto the roof headlining with the adhesive tape.

    NOTICE:
    1. Apply the tape securely in place.
    2. Do not touch the adhesive surface when applying the tape to prevent adhesion failure.

  1. Engage the 3 clamps.



4. INSTALL ROOF HEADLINING END PAD
  1. Remove the release paper from a new roof headlining end pad.

    HINT:
    After removing the release paper, keep the exposed adhesive free from foreign matter.



    B301172E01
  1. Align the markings on the roof headlining with the 2 roof headlining end pads and install the pads as shown in the illustration.
    Text in Illustration 
    *1
    Marking



5. INSTALL REAR NO. 2 SIDE RAIL SPACER LH (w/o Sliding Roof)


    B308238E01
  1. Align the markings on the roof headlining with a new rear No. 2 side rail spacer LH and install the spacer using hot-melt glue as shown in the illustration.
    Text in Illustration 
    *1
    Hot-melt Glue
    *2
    Marking



6. INSTALL REAR NO. 2 SIDE RAIL SPACER LH (w/ Sliding Roof)


    B301732E01
  1. Align the markings on the roof headlining with a new rear No. 2 side rail spacer LH and install the spacer using hot-melt glue as shown in the illustration.
    Text in Illustration 
    *1
    Hot-melt Glue
    *2
    Marking



7. INSTALL REAR NO. 2 SIDE RAIL SPACER RH

HINT:
Use the same procedure as for the LH side.



8. INSTALL SLIDING ROOF HEADLINING PAD (w/ Sliding Roof)


  1. Align the markings on the roof headlining with a new sliding roof headlining pad and install the pad using hot-melt glue as shown in the illustration.


    B301730E01


    Text in Illustration 
    *1
    Marking
    -
    -

    Standard Measurement:
    Dimension
    Measurement
    A
    10 mm (0.394 in.)



9. INSTALL NO. 3 ROOF SILENCER PAD (w/o Sliding Roof)


  1. w/ Silencer Pad:



    1. Align the markings on the roof headlining with a new No. 3 roof silencer pad and install the pad using hot-melt glue as shown in the illustration.


      B297748E01


      Text in Illustration 
      *1
      Hot-melt Glue
      *2
      Marking

      Standard Measurement:
      Dimension
      Measurement
      A
      20 mm (0.787 in.)



10. INSTALL NO. 2 ROOF SILENCER PAD (w/o Sliding Roof)


  1. w/ Silencer Pad:



    1. Align the markings on the roof headlining with a new No. 2 roof silencer pad and install the pad using hot-melt glue as shown in the illustration.


      B297746E01


      Text in Illustration 
      *1
      Hot-melt Glue
      *2
      Marking

      Standard Measurement:
      Dimension
      Measurement
      A
      20 mm (0.787 in.)



11. INSTALL NO. 1 ROOF SILENCER PAD (w/o Sliding Roof)


    B297744E01
  1. Align the markings on the roof headlining with a new No. 1 roof silencer pad and install the pad using hot-melt glue as shown in the illustration.
    Text in Illustration 
    *1
    Marking

    Standard Measurement:
    Dimension
    Measurement
    A
    20 mm (0.787 in.)



12. INSTALL FRONT ROOF SILENCER PAD (w/o Sliding Roof)


    B297742E01
  1. Align the markings on the roof headlining with a new 2 roof headlining silencer pads and install the pads using hot-melt glue as shown in the illustration.
    Text in Illustration 
    *1
    Marking

    Standard Measurement:
    Dimension
    Measurement
    A
    20 mm (0.787 in.)



13. INSTALL ROOF HEADLINING FORMING PAD (w/ Sliding Roof)


    B300817E01
  1. Align the markings on the roof headlining with a new 2 roof headlining forming pads and install the pads using hot-melt glue as shown in the illustration.
    Text in Illustration 
    *1
    Marking



14. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY


  1. Install the No. 2 antenna cord sub-assembly to the roof headlining assembly from the front of the vehicle.


    E237160E01


    Text in Illustration 
    *A
    w/o Sliding Roof
    *B
    w/ Sliding Roof
    *1
    Tape
    *2
    Marking Tape
    *3
    Protrusion A
    *4
    Edge
    *a
    Front
    -
    -

    HINT:
    Align the taped part of the antenna cable with the protrusion of the roof headlining, and apply tape to secure the cable to the headlining.

  1. Put the pieces of tape back to the positions shown in the illustration in order to secure the antenna cord to the roof headlining assembly.

  1. Engage each clamp.

    HINT:
    1. If the tape is no longer sticky, use other tape, such as packing tape, that has enough adhesion to secure the antenna cord to the roof headlining assembly.
    2. For the right front corner of the roof headlining assembly, align the marking tape on the antenna cord with the protrusion A of the roof headlining, and wrap tape around the antenna cord and roof headlining assembly once or twice to securely hold them. (1)
    3. For the right rear corner of the roof headlining assembly, align the marking tape on the antenna cord with the rear edge of the roof headlining, and secure the antenna cord to the roof headlining assembly with tape. (2)
    4. If the entire length of the antenna cord does not fit, adjust the length by tucking in the cord at the area shown in the illustration. (3)



15. INSTALL UPPER SHOULDER BELT ANCHOR COVER


    B297740
  1. Install the rear seat shoulder belt cover RH to the roof headlining.

  1. Engage the 4 claws to install the seat belt anchor cover.



16. INSTALL AMPLIFIER MICROPHONE ASSEMBLY (w/o Sliding Roof)
  1. Engage the 2 claws and install the amplifier microphone assembly to the roof headlining holder cover.



17. INSTALL ROOF HEADLINING RETAINER COVER (w/o Sliding Roof)
  1. Engage the 4 claws and install the roof headlining retainer cover.

  1. Connect the connector.



18. INSTALL ROOF HEADLINING PAD LH


    B300811E01
  1. Align the markings on the roof headlining with a new roof headlining pad LH and install the pad using hot-melt glue as shown in the illustration.
    Text in Illustration 
    *1
    Hot-melt Glue
    *2
    Marking



19. INSTALL ROOF HEADLINING PAD RH

HINT:
Use the same procedure as for the LH side.



20. INSTALL ROOF PANEL PAD (w/o Sliding Roof)


    B300809E01
  1. Align the markings on the roof headlining with a new roof panel pad and install the pad using hot-melt glue as shown in the illustration.
    Text in Illustration 
    *1
    Hot-melt Glue
    *2
    Marking



21. INSTALL ROOF PANEL PAD (w/ Sliding Roof)


    B301734E01
  1. Align the markings on the roof headlining with a new roof panel pad and install the pad using hot-melt glue as shown in the illustration.
    Text in Illustration 
    *1
    Hot-melt Glue
    *2
    Marking



22. INSTALL NO. 1 ROOF PANEL PAD

HINT:
Use the same procedure as for the LH side.



23. INSTALL REAR NO. 3 SIDE RAIL SPACER LH (w/o Sliding Roof)


  1. Align the markings on the roof headlining with a new rear No. 3 side rail spacer LH and install the spacer using hot-melt glue as shown in the illustration.


    B300807E01


    Text in Illustration 
    *1
    Hot-melt Glue
    -
    Marking



24. INSTALL REAR NO. 3 SIDE RAIL SPACER LH (w/ Sliding Roof)


  1. Align the markings on the roof headlining with a new rear No. 3 side rail spacer LH and install the spacer using hot-melt glue as shown in the illustration.


    B300819E01


    Text in Illustration 
    *1
    Hot-melt Glue
    -
    Marking



25. INSTALL REAR NO. 3 SIDE RAIL SPACER RH

HINT:
Use the same procedure as for the LH side.



26. INSTALL NO. 2 ROOF HEADLINING PAD (w/o Sliding Roof)


    B300805E01
  1. Align the markings on the roof headlining with a new No. 2 roof headlining pad and install the pad using hot-melt glue as shown in the illustration.
    Text in Illustration 
    *1
    Hot-melt Glue
    *2
    Marking



27. INSTALL NO. 2 ROOF HEADLINING PAD (w/ Sliding Roof)


    B300813E01
  1. Align the markings on the roof headlining with a new No. 2 roof headlining pad and install the pad using hot-melt glue as shown in the illustration.
    Text in Illustration 
    *1
    Marking



28. INSTALL ROOF HEADLINING PAD

HINT:
Use the same procedure as for the LH side.