Home › Vehicle Interior › SEAT BELT › REAR CENTER SEAT OUTER BELT ASSEMBLY

REAR CENTER SEAT OUTER BELT ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSPECT REAR CENTER SEAT LAP TYPE BELT ASSEMBLY


    B108365E02
  1. Before installing the rear seat lap type center belt assembly, check the ELR function.

    NOTICE:
    Do not disassemble the retractor.


    1. When the inclination of the retractor is 15° or less, check that the belt can be pulled from the retractor. When the inclination of the retractor is over 45°, check that the belt locks.
      Text in Illustration 
      *1
      Retractor
      *a
      Unlocked
      *b
      Locked
      *c
      45°
      If the result is not as specified, replace the rear seat lap type center belt assembly.



2. INSTALL REAR CENTER SEAT LAP TYPE BELT ASSEMBLY
  1. Engage the 2 guides and install the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B297191
  1. Turn the shoulder anchor clockwise approximately 90° to engage the guide.

  1. Install the rear center seat lap type belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



3. INSTALL ROOF SIDE INNER GARNISH RH
  1. Pass the floor anchor of the rear seat 3 point type outer belt assembly RH through the roof side inner garnish RH.

  1. Engage the 5 clips to install the roof side inner garnish RH.



    B297734
  1. Engage the guide and 4 claws to connect the belt guide.



4. CONNECT REAR CENTER SEAT LAP TYPE BELT ASSEMBLY
  1. Install the shoulder anchor of the rear center seat lap type belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 30 ft.*lbf }



    B300538
  1. Engage the 2 claws to close the cover as shown in the illustration.



5. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.

w/o Package Tray Trim:
w/ Package Tray Trim:


6. INSTALL REAR ABSORBER CAP RH (w/ Package Tray Trim)

HINT:
Use the same procedure as for the LH side .



7. CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH

HINT:
Use the same procedure as for the LH side .



8. INSTALL REAR DECK TRIM COVER
  1. Engage the 2 guides and 4 claws.

  1. Install the rear deck trim cover with the 2 clips.



9. INSTALL SPARE WHEEL CUSHION
  1. Install the 2 spare wheel cushions.



10. INSTALL REAR FLOOR MAT ASSEMBLY
  1. Install the rear floor mat assembly.



11. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)
  1. Install the package tray trim panel assembly.



12. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


    B299873E01
  1. Align the alignment mark (Red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.
    Text in Illustration 
    *a
    Alignment Mark (Red)
    *b
    Flange Position

    NOTICE:
    After installation, check that the corners fit correctly.



13. INSTALL REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure as for the LH side .



14. INSTALL REAR SEATBACK ASSEMBLY (for Bench Type Seatback)
  1. Place the rear seatback assembly in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Install the rear seatback assembly with the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm }

  1. Raise the rear seatback assembly.



15. INSTALL REAR SEAT CUSHION ASSEMBLY (for Bench Type Seatback)
  1. Place the rear seat cushion assembly in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.



    B296199
  1. Push out the seat belt buckles from the back of the rear seat cushion assembly so that they are positioned as shown in the illustration.



    B296198
  1. Engage the hook of the rear seat cushion assembly to the CRS anchor bracket.



    B296116
  1. Engage the 2 rear seat cushion lock hooks to install the rear seat cushion assembly as shown in the illustration.

  1. Confirm that the seat cushion is firmly installed.

    NOTICE:
    When installing the seat cushion, make sure that the seat belt buckles are not under the seat cushion.

  1. Engage the 2 clips.



16. INSTALL REAR SEATBACK ASSEMBLY RH (for Separate Type Seatback)
  1. Place the rear seatback assembly RH in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Install the rear seatback assembly RH with the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Raise the rear seatback assembly RH.



17. INSTALL REAR SEAT CUSHION ASSEMBLY (for Separate Type Seatback)
  1. Place the rear seat cushion assembly in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.



    B296199
  1. Push out the seat belt buckles from the back of the rear seat cushion assembly so that they are positioned as shown in the illustration.



    B296198
  1. Engage the hook of the rear seat cushion assembly to the CRS anchor bracket.



    B296116
  1. Engage the 2 rear seat cushion lock hooks to install the rear seat cushion assembly as shown in the illustration.

  1. Confirm that the seat cushion is firmly installed.

    NOTICE:
    When installing the seat cushion, make sure that the seat belt buckles are not under the seat cushion.

  1. Engage the 2 clips.



18. INSTALL FRONT CENTER FLOOR COVER
  1. Engage the 2 guides to install the front center floor cover.

  1. Install the 3 clips.



19. INSTALL FRONT FLOOR COVER LH
  1. Engage the 3 guides.



    B301490E01
  1. Engage the 3 clips <B> to install the front floor cover LH.

  1. Install the 2 clips <A>.



20. INSTALL FRONT FLOOR COVER RH
  1. Engage the 3 guides.



    B301488E01
  1. Engage the 3 clips <B> to install the front floor cover RH.

  1. Install the 2 clips <A>.



21. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY


22. INSTALL REAR SEAT HEADREST ASSEMBLY