NAVIGATION SYSTEM > OPERATION CHECK |
| CHECK NAVIGATION SYSTEM NORMAL CONDITION |
If the symptom is applicable to any of the following, it is intended behavior, and not a malfunction.
| Symptom | Answer |
| A longer route than expected is chosen. | Depending on the road conditions, the extension module may determine that a longer route is quicker. |
| Even when distance priority is high, the shortest route is not shown. | Some routes may not be advised due to safety concerns. |
| When the vehicle is put into motion immediately after the hybrid system starts, the navigation system deviates from the correct position. | If the vehicle starts before the navigation system activates, the system may not react. |
| When driving on certain types of roads, especially new roads, the vehicle position deviates from the correct position. | When the vehicle is driving on new roads not available on the hard disk drive, the system attempts to match it to another nearby road, causing the position mark to deviate. |
![]() |
The following symptoms are not malfunctions, but are caused by errors inherent in the GPS, gyro sensor, speed sensor or extension module.
The current position mark may be displayed on a nearby parallel road.
![]() |
Immediately after a fork in the road, the current vehicle position mark may be displayed on the wrong road.
![]() |
When the vehicle turns right or left at an intersection, the current vehicle position mark may be displayed on a nearby parallel road.
![]() |
When the vehicle is carried, such as on a ferry, and the vehicle itself is not driving, the current vehicle position mark may be displayed in the position where the vehicle was until a measurement can be performed by the GPS.
![]() |
When the vehicle travels on a steep hill, the current vehicle position mark may deviate from the correct position.
![]() |
When the vehicle makes a continuous turn (e.g. 360, 720, 1080 degrees), the current vehicle position mark may deviate from the correct position.
![]() |
When the vehicle moves erratically, such as constant lane changes, the current vehicle position mark may deviate from the correct position.
![]() |
When the ignition switch is turned on (ACC or IG) and the vehicle is turned on a turntable before parking, the current vehicle position mark may not indicate the correct direction. The same will occur when the vehicle comes out of the parking garage.
![]() |
When the vehicle travels on a snowy road or a mountain path with tire chains installed or using a spare tire, the current vehicle position mark may deviate from the correct position.
![]() |
When the tires are changed, the current vehicle position mark may deviate from the correct position.
| CHECK PANEL & STEERING SWITCH |
Enter diagnostic mode (Click here).
![]() |
Select "Function Check/Setting" from the "Service Menu" screen.
![]() |
Select "Panel & Steering Switch" from the "Function Check/Setting I" screen.
![]() |
Panel & Steering Switch Check Mode
| Display | Content |
| *a: Switch condition | "Pushed" is displayed when any switch is pushed |
| *b: Number of switches pushed |
|
| *c: Rotary switch direction | Direction of rotary switch is displayed |
Operate each switch and check that the switch conditions are correctly displayed.
| CHECK TOUCH SWITCH |
Enter diagnostic mode (Click here).
![]() |
Select "Function Check/Setting" from the "Service Menu" screen.
![]() |
Select "Touch Switch" from the "Function Check/Setting I" screen.
![]() |
Touch Switch Check
Touch the display anywhere in the open area to perform the check when the "Touch Switch Check" screen is displayed.
| CHECK COLOR BAR |
Enter diagnostic mode (Click here).
![]() |
Select "Function Check/Setting" from the "Service Menu" screen.
![]() |
Select "Color Bar" from the "Function Check/Setting I" screen.
![]() |
Color Bar Check Mode
Select a color bar from the "Color Bar Check Mode" screen.
Check the display color.
| CHECK VEHICLE SIGNAL |
Enter diagnostic mode (Click here).
![]() |
Select "Function Check/Setting" from the "Service Menu" screen.
![]() |
Select "Vehicle Signal" from the "Function Check/Setting I" screen.
![]() |
Vehicle Signal Check Mode
| Display | Content |
| Battery | Auxiliary battery voltage is displayed. |
| IG | Ignition switch ON/OFF state is displayed. |
| PKB | Parking brake ON/OFF state is displayed. |
| REV | Reverse signal ON/OFF state is displayed. |
| SPEED | Vehicle speed is displayed in km/h. |
| TAIL | Tail signal (Light control switch) ON/OFF state is displayed. |
| ADIM/TCAN | Brightness state DIM (with) / BRIGHT (without) is displayed. |
When the "Vehicle Signal Check Mode" screen is displayed, check all the vehicle signal conditions.
| CHECK MICROPHONE LEVEL |
Enter diagnostic mode (Click here).
![]() |
Select "Function Check/Setting" from the "Service Menu" screen.
![]() |
Select "Next Page" from the "Function Check/Setting I" screen.
![]() |
Select "EXT BOX" from the "Function Check/Setting II" screen.
![]() |
Select "Microphone Level" from the "Extension Module Service Mode" screen.
![]() |
Microphone Level Test
| Display | Content |
| *a: Microphone input level meter | Monitors the microphone input level every 0.1 seconds and displays the results in 8 different levels. |
When speaking into the microphone, check that the microphone input level meter changes according to the input level.
| CHECK DIAGNOSTICS |
Enter diagnostic mode (Click here).
![]() |
Select "Function Check/Setting" from the "Service Menu" screen.
![]() |
Select "Next Page" from the "Function Check/Setting I" screen.
![]() |
Select "EXT BOX" from the "Function Check/Setting II" screen.
![]() |
Select "Diagnostics" from the "Extension Module Service Mode" screen.
![]() |
Diagnostics Tests
Check the connection condition of the USB device and each item (antenna) on the "Diagnostics Tests" screen.
| CHECK SOFTWARE ERROR HISTORY |
Check software error history.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (READY).
Turn the Techstream on.
Enter the following menus: Body Electrical / Navigation System / Utility / Software Error History.
When an item is stored for Software Error History, record it before repairing the radio and display receiver assembly.
| Error Description | Trigger | Detail |
| Software Reset | Navi Microcomputer | Hexadecimal Number |
| Audio Microcomputer | ||
| CAN Microcomputer | ||
| No Video Signal | Front Monitor | |
| Rear Monitor | ||
| MOST Cold Restart | Always |
Clear software error history.
When DTCs are cleared using any of the following operations, Software Error History will be cleared as well (Click here).
| CHECK OPTICAL DISC ERROR HISTORY |
Check optical disc error history.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (READY).
Turn the Techstream on.
Enter the following menus: Body Electrical / Navigation System / Utility / Optical Disc Error History.
When an item is stored for Optical Disc Error History, record it before proceeding with troubleshooting.
| Display | Content |
| Error Type | Displays the type of error. |
| Device | Displays the malfunctioning device. |
| Date | Displays the date and time that the malfunction occurred. |
| Error Type | Detection Condition | Action |
| Read Error | When a disc read error occurs. | Proceed to next suspected area shown in Problem Symptoms Table (Click here) |
| Disc damaged/upside down/dirty | When it is determined that any of the following is the cause of the disc read error:
| |
| Cannot determine disc type | An unsuitable disc is inserted. | |
| DPS error | When an error occurs while decoding MP3/WMA files. | |
| Some files are corrupt |
| |
| Some files cannot be found |
| |
| Copy protection violation | When a file with copyright protection that cannot be played back is played back. |
| Device | Component |
| DVD-P | Not available |
| CD-P | Radio and display receiver assembly |
| R-Seat DVD-P | Not available |
Clear optical disc error history.
When DTCs are cleared using any of the following operations, Optical Disc Error History will be cleared as well (Click here).
| ENTUNE RESET PROCEDURE (w/ Entune Function) |
Duplicate the problem symptom.
Check for DTCs and repair the systems for which any DTCs are output (Click here).
Check cellular phone compatibility.
Go to TIS "Bluetooth" Compatibility Portal and check if the cellular phone/vehicle is compatible.
If the phone is not compatible, recommend to the customer a compatible cellular phone.
Delete all paired devices from the cellular phone.
The procedure varies based on phone model. Contact the service provider or cellular phone manufacturer if assistance is required.
Remove the Entune app from the phone.
The procedure varies based on phone model. Contact the service provider or cellular phone manufacturer if assistance is required.
Reset the phone.
Turn off the phone and remove the auxiliary battery for 15 seconds. For instructions on how to reset cellular devices, refer to the appropriate manufacturer's website.
Reinstall the Entune app on the phone. (If removed.)
The procedure varies based on phone model. Contact the service provider or cellular phone manufacturer if assistance is required.
Reset the extension module.
Display the "Navigation Prompt Volume" screen.
![]() |
From the "Navigation Prompt Volume" screen, touch the corners of the screen in the following order: Upper right → Lower right → Upper right → Lower right → Upper right → Lower right.
![]() |
Select "General" from the Entune system status display screen.
![]() |
Select "Reset Extension Box" from the "General" screen, delete all personal data from the head unit.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Record all radio station presets.
Disconnect the cable from the negative (-) auxiliary battery and leave it disconnected for 2 minutes.
Check if the problem symptom has been repaired.