Home › Vehicle Interior › HEATING / AIR CONDITIONING › CONDENSER

CONDENSER > INSTALLATION

for Preparation Click here



1. INSTALL NO. 1 COOLER CONDENSER CUSHION
  1. Install the 4 No. 1 cooler condenser cushions to the cooler condenser assembly.



2. INSTALL COOLER CONDENSER ASSEMBLY
  1. Engage the 2 guides to install the cooler condenser assembly.

    NOTICE:
    Do not damage the condenser or radiator when installing the cooler condenser assembly.

    HINT:
    If a new cooler condenser assembly is installed, add compressor oil to the condenser as follows.

    Capacity:
    Add 40 cc (1.35 fl. oz.)

    Compressor oil:
    ND-OIL 11 or equivalent.



3. CONNECT LIQUID PIPE SUB-ASSEMBLY
  1. Remove the attached vinyl tape from the liquid pipe sub-assembly and the connecting part of the cooler condenser assembly.

  1. Apply sufficient compressor oil to a new O-ring and the fitting surface of the pipe joint.

    Compressor oil:
    ND-OIL 11 or equivalent.

  1. Install the O-ring onto the liquid pipe sub-assembly.

  1. Install the liquid pipe sub-assembly onto the cooler condenser assembly with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



4. CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE
  1. Remove the attached vinyl tape from the No. 1 cooler refrigerant discharge hose and the connecting part of the cooler condenser assembly.

  1. Apply sufficient compressor oil to a new O-ring and the fitting surface of the hose joint.

    Compressor oil:
    ND-OIL 11 or equivalent.

  1. Install the O-ring onto the No. 1 cooler refrigerant discharge hose.

  1. Install the No. 1 cooler refrigerant discharge hose onto the cooler condenser assembly with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



5. INSTALL NO. 2 FAN SHROUD
  1. Install the No. 2 fan shroud with the 2 bolts and 2 claws.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



6. INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY
  1. Install the 2 radiator support cushions.



    A267979E01
  1. Temporarily install the upper radiator support sub-assembly with the 5 bolts.

  1. Fully tighten the bolt (A).

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Fully tighten the bolt (B).

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Fully tighten the bolt (C).

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

  1. Connect the clamp of the hood lock control cable.

  1. Connect the cooling fan ECU connector and 3 clamps.

  1. Connect the horn connector.



7. INSTALL HOOD LOCK SUPPORT SUB-ASSEMBLY
  1. Install the hood lock support sub-assembly with the 2 bolts.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

  1. Connect the connector.



8. INSTALL HOOD LOCK ASSEMBLY
  1. Apply MP grease to the sliding areas of the hood lock assembly.

  1. Connect the hood lock control cable.

  1. Install the hood lock with the 3 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



9. INSTALL FRONT BUMPER REINFORCEMENT


    B307343
  1. Install the front bumper reinforcement with the 6 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

  1. Engage the 2 clamps and install the wire harness.



10. INSTALL FRONT BUMPER ENERGY ABSORBER


    B307342
  1. Engage the 2 guides to install the front bumper energy absorber.



11. INSTALL RADIATOR SUPPORT EXTENSION LH


    B307340
  1. Engage the 2 claws and install the radiator support extension LH.

  1. Engage the 2 clamps to install the thermistor assembly.



12. INSTALL RADIATOR SUPPORT EXTENSION RH


    B307341
  1. Engage the 2 claws and install the radiator support extension RH.



13. INSTALL NO. 2 RADIATOR SIDE AIR SEAL


    B307338
  1. Engage the 2 claws and install the No. 2 radiator side air seal.



14. INSTALL NO. 1 RADIATOR SIDE AIR SEAL


    B307339
  1. Engage the 2 claws and install the No. 1 radiator side air seal.



15. INSTALL RADIATOR SUPPORT OPENING COVER


    B310542
  1. Install the radiator support opening cover with the 6 clips.



16. INSTALL FRONT BUMPER ASSEMBLY
(Click here)


17. INSPECT HOOD SUB-ASSEMBLY


  1. Check that the clearance measurements of areas "a" through "f" are within each standard range.


    B301498E01


    Standard Clearance 
    Area
    Measurement
    Area
    Measurement
    a
    -0.85 to 3.15 mm (-0.0335 to 0.124 in.)
    b
    1.65 to 5.65 mm (0.0650 to 0.222 in.)
    c
    -1.85 to 2.15 mm (-0.0728 to 0.0847 in.)
    d
    2.35 to 6.35 mm (0.0925 to 0.250 in.)
    e
    2.0 to 5.0 mm (0.0787 to 0.197 in.)
    f
    -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)



18. ADJUST HOOD SUB-ASSEMBLY


  1. Horizontally and vertically adjust the hood.



      B301499
    1. Loosen the 4 hinge bolts of the hood.

    2. Adjust the clearance between the hood and front fender by moving the hood.

    3. Tighten the 4 hinge bolts after the adjustment.

      Torque:
      13 N*m{ 133 kgf*cm , 10 ft.*lbf }



  1. Adjust the height of the front end of the hood using the cushion rubbers.



      B297000
    1. Adjust the 2 cushion rubbers so that the heights of the hood and fender are aligned.

      HINT:
      Raise or lower the front end of the hood by turning the 2 cushion rubbers.



  1. Adjust the hood lock.



      B301500
    1. Loosen the 3 bolts.

    2. Tighten the bolts after adjustment.

      Torque:
      7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

    3. Check that the striker can engage with the hood lock smoothly.



19. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT
  1. Perform vacuum purging using a vacuum pump or appropriate equipment.



  1. Charge the air conditioning system with refrigerant.

    Refrigerant type:
    HFC-134a (R134a)



    E143108E11


    Text in Illustration 
    *a
    Sub-cool System
    *b
    High Pressure
    *c
    Refrigerant Amount
    *d
    Standard charge amount
    *e
    Charge additional 100g (3.5 oz.)
    *f
    Point where bubbles disappear
    *g
    Mean value in proper range
    *h
    Overcharged

    Standard charge amount:
    370 to 470g (13.0 to 16.6oz.)

    SST
    09985-20010   (09985-02010, 09985-02050, 09985-02060, 09985-02070, 09985-02080, 09985-02090, 09985-02110, 09985-02130, 09985-02140, 09985-02150)

    NOTICE:
    1. Do not turn the A/C switch on before charging the air conditioning system with refrigerant. Doing so may cause the compressor to work without refrigerant, resulting in overheating of the compressor.
    2. The refrigerant amount should be checked by quantity (weight).

    HINT:
    Ensure that sufficient refrigerant is available to recharge the system when using a refrigerant recovery unit. Refrigerant recovery units are not always able to recover 100% of the refrigerant from an air conditioning system.



20. WARM UP COMPRESSOR
  1. Keep the A/C switch on for at least 2 minutes to warm up the compressor.

    NOTICE:
    To prevent damage to the compressor, be sure to warm up the compressor when turning the air conditioning on after removing and installing air conditioning system lines (including the compressor).



21. INSPECT FOR REFRIGERANT LEAK
  1. After recharging the air conditioning system with refrigerant, inspect for refrigerant leaks using a halogen leak detector.

  1. Carry out the test under the following conditions:

    1. Turn the power switch off.
    2. Ensure good ventilation (the halogen leak detector may react to volatile gases which are not refrigerant, such as gasoline vapor and exhaust gas).
    3. Repeat the inspection 2 or 3 times.
    4. Measure the pressure to make sure that there is some refrigerant remaining in the air conditioning system.
      Pressure when the compressor is off: approx. 392 to 588 kPa (4.0 to 6.0 kgf/cm2, 57 to 85 psi)



    I042222E40
  1. Using a halogen leak detector, inspect for refrigerant leaks from the air conditioning system.
    Text in Illustration 
    *1
    Halogen Leak Detector
    *a
    Inspect for Leak



    N014519E08
  1. Bring the halogen leak detector close to the drain hose with the detector power off, and then turn the detector on.
    Text in Illustration 
    *1
    Halogen Leak Detector
    *2
    Drain Hose

    HINT:
    1. After the blower motor has stopped, leave the cooling unit for more than 15 minutes.
    2. Bring the halogen leak detector sensor under the drain hose.
    3. When bringing the halogen leak detector close to the drain hose, make sure that the halogen leak detector does not react to volatile gases. If it is not possible to avoid interference from volatile gases, the vehicle should be lifted up to allow checking for leaks.

  1. If a refrigerant leak is not detected from the drain hose, remove the blower motor control from the cooling unit. Insert the halogen leak detector sensor into the unit and check for a leak.

  1. Disconnect the pressure sensor connector and leave it for approximately 20 minutes. Bring the halogen leak detector close to the pressure sensor and check for a leak.

    HINT:
    When checking for leaks, the presence of oily dirt at a joint can indicate a leak.