Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART KEY SYSTEM (for Entry Function)

DTC    B27A8    Open in Outside Luggage Compartment Electrical Key Antenna Circuit

for Preparation Click here


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the electrical key antenna (outside luggage). For the electrical key antenna (outside luggage) to detect when the electrical key transmitter sub-assembly is brought close to the vehicle, the received request signal is transmitted within approximately 1.0 m (3.28 ft.) of the back door. DTC B27A8 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage) (between terminals CLG8 and ANTE8, or terminals CG8B and CLGB).

DTC Code
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B27A8
An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage) (CLG8 - ANTE8, CG8B - CLGB) (1 trip detection logic*).
  1. Wire harness or connector
  2. Electrical key antenna (outside luggage)
  3. Certification ECU (smart key ECU assembly)
Any time
  1. *: Only output while a malfunction is present.

Vehicle Condition and Fail-safe Operation when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Operation when Malfunction Detected
Entry lock or unlock operation cannot be performed for luggage compartment door
-

Related Data List and Active Test 
DTC Code
Data List and Active Test
B27A8
Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM


B274845E63


INSPECTION PROCEDURE

NOTICE:
  1. The smart key system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart key system (for Entry Function) after confirming that the communication systems are functioning properly.
  2. When using the Techstream with the power switch off to troubleshoot:
    Connect the Techstream to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the Techstream and vehicle begins.
  3. Before replacing the certification ECU (smart key ECU assembly), refer to the smart key system (for Entry Function) precaution (Click here).
  4. After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".
  5. The electrical key antenna (outside luggage) has an antenna coil between ANTE8 and CLGB terminals.

1.CHECK CONNECTOR CONNECTION
  1. Turn the power switch off.

  1. Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage).

    OK:
    Connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


2.CHECK HARNESS AND CONNECTOR (ELECTRICAL KEY ANTENNA - CERTIFICATION ECU)
  1. Disconnect the G53 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the M19 electrical key antenna (outside luggage) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G53-2 (CLG8) - M19-1 (ANTE8)
    Always
    Below 1 Ω
    G53-1 (CG8B) - M19-2 (CLGB)
    Always
    Below 1 Ω
    G53-2 (CLG8) or M19-1 (ANTE8) - Body ground
    Always
    10 kΩ or higher
    G53-1 (CG8B) or M19-2 (CLGB) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE)


    B226391E17
  1. Remove the electrical key antenna (outside luggage) (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (ANTE8) - 2 (CLGB)
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Electrical Key Antenna (Outside Luggage))



NG
REPLACE ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE) (Click here)
OK


4.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
  1. Temporarily replace the certification ECU (smart key ECU assembly) with a new one (Click here).


NEXT


5.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


6.CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B27A8 is not output.



NG
REPLACE ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE) (Click here)
OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)