DTC P0069-273 Manifold Absolute Pressure - Barometric Pressure Correlation |

| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
| P0069 | 273 | Difference between the atmospheric pressure value of the atmosphere pressure sensor in the inverter with converter assembly and the manifold absolute pressure sensor assembly exceeds a specified value and the same condition recurs after 3 hours or more when driving in EV drive mode. (1 trip detection logic) |
|
| DTC No. | Data List |
| P0069-273 |
|

| 1.CHECK DTC OUTPUT (ENGINE AND ECT) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (READY).
Fully depress the accelerator pedal for 5 seconds to start the engine and keep it running.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Check if DTCs are output.
| Result | Proceed to |
| Except the following. | A |
| Any of the following DTCs are also output. | B |
| DTC No. | Relevant Diagnosis |
| P0107 | Manifold Absolute Pressure / Barometric Pressure Circuit Low Input |
| P0108 | Manifold Absolute Pressure / Barometric Pressure Circuit High Input |
| P106A | Evaporative Emission System Pressure Sensor - Manifold Absolute Pressure Correlation |
Turn the ignition switch off.
|
| ||||
| A | |
| 2.CHECK DTC OUTPUT (HYBRID CONTROL) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check if DTCs are output.
| Result | Proceed to |
| P0069-273 only is output or DTCs except the ones in the table below are also output. | A |
| Any of the following DTCs are also output. | B |
| DTC No. | Relevant Diagnosis |
| P0A1A-151, 155, 156, 658, 659 | Generator Control Module |
| P0A1B-193, 512, 661, 786 | Drive Motor "A" Control Module |
| P0A1D-148 | Hybrid Powertrain Control Module |
| P2228-268 | Barometric Pressure Sensor "A" Circuit Low |
| P2229-269 | Barometric Pressure Sensor "A" Circuit High |
| P2511-149 | ECM/PCM Power Relay Sensor Circuit Intermittent |
| P324E-788 | MG-ECU Power Relay Intermittent Circuit |
| U0100-211, 530 | Lost Communication with ECM/PCM "A" |
| U0110 (all INF codes)*1 | Lost Communication with Drive Motor Control Module "A" |
Turn the ignition switch off.
|
| ||||
| A | |
| 3.READ VALUE USING TECHSTREAM (MAP, ATMOSPHERE PRESSURE) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / MAP, Atmosphere Pressure.
Using the table, read the normal atmospheric pressure value for the applicable altitude.

Compare the MAP and Atmosphere Pressure values in the Data List with the normal atmospheric value from the table.
| Result | Proceed to |
| Other than the following. | A |
| Difference between MAP in Data List and "normal atmospheric pressure value" is 10 kPa or more. | B |
| Difference between Atmosphere Pressure in Data List and "normal atmospheric pressure value" is 10 kPa or more. | C |
Turn the ignition switch off.
|
| ||||
|
| ||||
| A | |
| 4.READ VALUE USING TECHSTREAM (MAP) |
Move the shift lever to P.
Enter the following menus: Powertrain / Hybrid Control / Data List / MAP
Read the MAP value in the Data List with the engine stopped.
While depressing the brake pedal, Turn the ignition switch to ON (READY).
With the READY indicator light illuminated, fully depress the accelerator pedal.
Read the MAP value in the Data List with the engine running.
Compare the MAP value noted with the engine stopped and the MAP value noted with the engine running.
Turn the ignition switch off.
|
| ||||
| OK | |
| 5.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR |
| NEXT | |
| 6.READ VALUE USING TECHSTREAM (MAP, ATMOSPHERE PRESSURE) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / MAP, Atmosphere Pressure.
Compare the Data List item "MAP" with "Atmosphere Pressure".
| Result | Proceed to |
| The difference between "MAP" and "Atmosphere Pressure" is 10 kPa or more. | A |
| The difference between "MAP" and "Atmosphere Pressure" is less than 10 kPa. | B |
Turn the ignition switch off.
|
| ||||
| A | ||
| ||
| 7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MANIFOLD ABSOLUTE PRESSURE SENSOR) |
![]() |
Disconnect the manifold absolute pressure sensor connector.
Turn the ignition switch to ON (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C15-3 (VC) - C15-2 (E2) | Ignition switch ON (IG) | 4.75 to 5.25 V |
| C15-1 (PIM) - C15-2 (E2) | Ignition switch ON (IG) | 3.0 to 5.0 V |
| *a | Front view of wire harness connector (to Manifold Absolute Pressure Sensor) |
|
| ||||
| OK | |
| 8.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR |
| NEXT | |
| 9.CLEAR DTC |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Clear DTCs and freeze frame data.
Turn the ignition switch off.
| NEXT | |
| 10.READ VALUE USING TECHSTREAM (MAP, ATMOSPHERE PRESSURE) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / MAP, Atmosphere Pressure.
Compare the Data List item "MAP" with "Atmosphere Pressure".
| Result | Proceed to |
| The difference between "MAP" and "Atmosphere Pressure" is less than 10 kPa. | A |
| The difference between "MAP" and "Atmosphere Pressure" is 10 kPa or more. | B |
Turn the ignition switch off.
|
| ||||
| A | ||
| ||
| 11.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM) |
Disconnect the manifold absolute pressure sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C15-3 (VC) - C10-118 (VCPM) | Always | Below 1 Ω |
| C15-2 (E2) - C10-119 (EPIM) | Always | Below 1 Ω |
| C15-1 (PIM) - C10-87 (PIM) | Always | Below 1 Ω |
| C15-3 (VC) or C10-118 (VCPM) - Body ground | Always | 10 kΩ or higher |
| C15-1 (PIM) or C10-87 (PIM) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||