FRONT DOOR LOCK > REMOVAL |
| 1. PRECAUTION |
| 2. REMOVE FRONT FLOOR COVER RH |
![]() |
Using a clip remover, remove the 2 clips <A>.
Disengage the 3 clips <B>.
![]() |
Disengage the 3 guides and remove the front floor cover RH.
| 3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL |
| 4. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side) |
![]() |
Disengage the 10 claws and 4 guides.
Disconnect the connector and remove the power window regulator master switch assembly with front door armrest base panel.
| 5. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side) |
![]() |
Disengage the 10 claws and 4 guides.
Disconnect the connector and remove the power window regulator switch assembly with front door armrest base panel.
| 6. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the claw and open the cover.
| *1 | Protective Tape |
![]() |
Remove the 3 screws.
![]() |
Disengage the 8 clips and remove the front door trim board sub-assembly as shown in the illustration.
![]() |
Disconnect the front door lock remote control cable assembly and front door inside locking cable from the front door trim board sub-assembly.
| *1 | Front Door Inside Locking Cable Assembly |
| *2 | Front Door Lock Remote Control Cable Assembly |
| 7. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY |
![]() |
Disconnect the connector.
Remove the 2 screws and front No. 2 speaker assembly.
| 8. DISCONNECT DOOR SIDE AIRBAG SENSOR CONNECTOR |
Disconnect the door side airbag sensor connector .
| 9. REMOVE FRONT DOOR SERVICE HOLE COVER |
![]() |
Remove the bolt and disconnect the earth wire.
Remove the front door service hole cover.
| 10. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY |
![]() |
Remove the front door No. 2 service hole cover.
Connect the cable to the negative (-) auxiliary battery terminal and power window regulator master switch assembly and move the front door glass subassembly so that the door glass bolts can be seen.
Disconnect the negative (-) auxiliary battery terminal and power window regulator master switch assembly.
![]() |
Remove the 2 bolts.
![]() |
Remove the front door glass sub-assembly as shown in the illustration.
| 11. REMOVE FRONT DOOR GLASS RUN |
![]() |
Remove the front door glass run.
| 12. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY |
![]() |
Remove the bolt.
Disengage the guide and remove the front door rear lower frame sub-assembly.
| 13. REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (w/ Lock Cylinder) |
![]() |
Remove the hole plug.
![]() |
Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover with lock cylinder assembly.
| 14. REMOVE FRONT DOOR LOCK ASSEMBLY |
![]() |
Disconnect the connector.
| *1 | Front Door Lock Open Rod |
Using a T30 "TORX" socket wrench, remove the 3 screws.
Move the front door lock assembly downward and disconnect the front door lock open rod, and then remove the front door lock assembly.
When reusing the front door lock assembly:
![]() |
Remove the door lock wiring harness seal from the front door lock assembly.
| 15. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY |
![]() |
Remove the front door lock remote control cable assembly as shown in the illustration.
| 16. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY |
![]() |
Using a screwdriver, disengage the 3 claws as shown in the illustration.
![]() |
Remove the front door inside locking cable assembly as shown in the illustration.