REAR DOOR LOCK > INSTALLATION |
| 1. INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY |
![]() |
Install the rear door inside locking cable assembly as shown in the illustration.
![]() |
Engage the 3 claws as shown in the illustration.
| 2. INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY |
![]() |
Install the rear door lock remote control cable assembly as shown in the illustration.
![]() |
Engage the claw as shown in the illustration.
| 3. INSTALL REAR DOOR LOCK ASSEMBLY |
Apply MP grease to the sliding parts of the rear door lock assembly.
When reusing the rear door lock assembly:
Install a new door lock wiring harness seal to the rear door lock assembly.
![]() |
Insert the rear door lock assembly to the rear door outside handle release plate, and set it to the rear door panel.
| *1 | Release Plate |
Make sure that the rear door outside handle frame release plate is securely connected to the rear door lock assembly.
Using a T30 "TORX" socket wrench, install the rear door lock assembly with the 3 screws.
Install the rear door lock child protection cover.
| 4. INSTALL REAR DOOR GLASS SUB-ASSEMBLY |
![]() |
Insert the rear door glass as indicated by the arrows in the order shown in the illustration.
Slide the lower section of the rear door glass sub-assembly and engage the rear door glass sub-assembly to the rear door window regulator assembly.
| 5. INSTALL REAR DOOR QUARTER WINDOW GLASS |
![]() |
Install the rear door quarter window glass in the direction indicated by the arrow in the illustration.
| 6. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY |
![]() |
Temporary install the rear door window division bar sub-assembly with the 2 bolts.
Install the rear door window division bar sub-assembly with the 2 bolts and screw.
| 7. INSTALL REAR DOOR GLASS RUN |
![]() |
Install the rear door glass run.
| 8. INSTALL REAR DOOR SERVICE HOLE COVER |
Apply butyl tape to the rear door panel.
Pass the rear door lock remote control cable, rear door inside locking cable and each connector through a new rear door service hole cover.
![]() |
Attach the rear door service hole cover according to the reference points on the rear door panel.
| *a | Reference Point |
| 9. CONNECT REAR DOOR WEATHERSTRIP |
Connect the upper part of the rear door weatherstrip.
| 10. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY |
![]() |
Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly to the rear door inside handle.
| *1 | Rear Door Inside Locking Cable Assembly |
| *2 | Rear Door Lock Remote Control Cable Assembly |
![]() |
Install the clip.
![]() |
Engage the 7 clips.
![]() |
Install the rear door trim board sub-assembly with the 3 screws.
![]() |
Engage the claw and close the cover.
| 11. INSTALL REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window) |
![]() |
Install the window regulator handle plate.
| *a | Inside of Vehicle |
Install the clip to the rear door window regulator handle assembly.
Fully close the rear door window.
![]() |
Install the rear door window regulator handle with the clip at the angle shown in the illustration.
| *a | Assemble when fully closed |
| Area | Measurement |
| A | -30° to 30° |
| 12. INSTALL REAR DOOR ARMREST BASE UPPER PANEL (w/o Power Window) |
![]() |
Engage the 2 guides and 5 claws to install the rear door armrest base upper panel.
| 13. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL (w/ Power Window) |
Connect the connector.
![]() |
Engage the 3guides and 8 claws to install the rear power window regulator switch assembly with rear door armrest base panel.
| 14. INSTALL REAR DOOR FRAME GARNISH |
![]() |
Engage the guide.
Engage the 2 clips and 3 claws to install the rear door frame garnish.
| 15. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL (w/ Power Window) |
| 16. INSTALL FRONT FLOOR COVER RH (w/ Power Window) |
Engage the 3 guides.
![]() |
Engage the 3 clips <B> to install the front floor cover RH.
Install the 2 clips <A>.
| 17. CHECK POWER WINDOW CONTROL SYSTEM (w/ Power Window) |