Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT SEAT SIDE AIRBAG ASSEMBLY

FRONT SEAT SIDE AIRBAG ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL FRONT SEAT AIRBAG ASSEMBLY

CAUTION:
  1. The nuts must not be reused.
  2. Make sure that the separate type front seatback spring assembly is not deformed. If it is, replace it with a new one.

  1. Install the front seat airbag assembly with 2 new nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Engage the 2 clamps.



2. INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD (w/ Non-removable Headrest)
  1. Temporarily install the separate type front seatback cover with pad.

  1. Install the 3 brackets with the 2 nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    CAUTION:
    1. For vehicles with a front seat airbag assembly, the separate type front seatback cover must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.
    2. Make sure that the strap is not twisted after installing the nut.
    3. Install the bracket securely.



    B296404
  1. Turn back the separate type front seatback cover.



    B296402
  1. Using hog ring pliers, install 3 new hog rings.

    NOTICE:
    1. Be careful not to damage the separate type front seatback cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.



    B311802
  1. Using hog ring pliers, install 5 new hog rings.

    NOTICE:
    1. Be careful not to damage the separate type front seatback cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.



3. INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD (w/ Removable Headrest)
  1. Temporarily install the separate type front seatback cover with pad.

  1. Engage the 4 claws to install the 2 front seat headrest supports.

  1. Install the 3 brackets with the 2 nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    CAUTION:
    1. For vehicles with a front seat airbag assembly, the separate type front seatback cover must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.
    2. Make sure that the strap is not twisted after installing the nut.
    3. Install the bracket securely.



    B301370
  1. Turn back the separate type front seatback cover.



    B301368
  1. Using hog ring pliers, install 3 new hog rings.

    NOTICE:
    1. Be careful not to damage the separate type front seatback cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.



    B311802
  1. Using hog ring pliers, install 5 new hog rings.

    NOTICE:
    1. Be careful not to damage the separate type front seatback cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.



4. CONNECT FRONT SEAT AIRBAG ASSEMBLY
w/ Non-removable Headrest:
w/ Removable Headrest:


5. CONNECT SEPARATE TYPE FRONT SEATBACK COVER
w/ Non-removable Headrest:
w/ Removable Headrest:


6. INSTALL FRONT SEAT ASSEMBLY
w/ Non-removable Headrest: (Click here)
w/ Removable Headrest: (Click here)


7. PERFORM DIAGNOSTIC SYSTEM CHECK
(Click here)