SMART KEY SYSTEM (for Start Function) > OPERATION CHECK |
| OPERATION DESCRIPTION |
Push-button start function:
When the electrical key transmitter sub-assembly is in a detection area inside the vehicle and the brake pedal is depressed, the hybrid control system is started by pressing the power switch.
When the electrical key transmitter sub-assembly is in a detection area inside the vehicle and the brake pedal is not depressed, the power source mode is changed by pressing the power switch. The power source mode changes in the following order every time the power switch is pressed: off → on (ACC) → on (IG) → off.
After getting into the vehicle while carrying the electrical key transmitter sub-assembly when the power switch is off, if the power switch is pressed while not depressing the brake pedal, the power source mode changes to on (ACC).
After getting into the vehicle while carrying the electrical key transmitter sub-assembly when the power switch is off, if the power switch is pressed 2 times without depressing the brake pedal, the power source mode changes to on (IG).
![]() |
After getting into the vehicle while carrying the electrical key transmitter sub-assembly when the power switch is off, if the brake pedal is depressed while the shift lever is in P, or the smart warning light is displayed.
The hybrid control system starts if the power switch is pressed when the smart warning light is displayed.
| *a | Smart Warning Light Displayed |
Changing the power source mode when the electrical key transmitter sub-assembly does not operate correctly due to wave interference or transmitter battery depletion:
Unlock the door using the built-in mechanical key and get into the vehicle while carrying the electrical key transmitter sub-assembly.
While depressing the brake pedal and facing the logo side of the electrical key transmitter sub-assembly towards the power switch, hold the electrical key transmitter sub-assembly near the power switch.
A buzzer in the combination meter assembly sounds and the power source mode changes to on (IG). Pressing the power switch without depressing the brake pedal turns the power source mode from on (IG) to off.
Starting the hybrid control system when the electrical key transmitter sub-assembly does not operate correctly due to wave interference or transmitter battery depletion:
Unlock the door using the built-in mechanical key and get into the vehicle while carrying the electrical key transmitter sub-assembly.
While depressing the brake pedal with the shift lever in P, while facing the logo side of the electrical key transmitter sub-assembly towards the power switch, hold the electrical key transmitter sub-assembly near the power switch.
A buzzer in the combination meter assembly sounds, the power source mode changes to on (IG) and the smart warning light is displayed.
Press the power switch with the brake pedal depressed to start the hybrid control system.
| CHECK PUSH-BUTTON START FUNCTION |
Check the push-button start function:
Get into the vehicle while carrying the electrical key transmitter sub-assembly with the power switch off. With the shift lever in P, check that the smart warning light is displayed when the brake pedal is depressed. Then check that the hybrid control system starts when the power switch is pressed after the smart warning light is displayed.
While the brake pedal is released and the electrical key transmitter sub-assembly is being carried, check that the power source mode changes in the following order when the power switch is pressed: off → on (ACC) → on (IG) → off.
With the shift lever in P, check that the steering lock operates when a door is opened.
![]() |
Inspect the push start operating range (front floor). Place the electrical key transmitter sub-assembly on the front seat at either inspection point so that it is facing in the direction shown in the illustration and check that the hybrid system can be started.
| *a | Inspection Point |
![]() |
Inspect the push start operating range (steering column). Place the electrical key transmitter sub-assembly on the steering column at inspection point so that it is facing in the direction shown in the illustration and check that the hybrid system can be started.
| *a | Inspection Point |
![]() |
Inspect the push start operating range (rear floor). Place the electrical key transmitter sub-assembly on the rear seat at either inspection point so that it is facing in the direction shown in the illustration and check that the hybrid system can be started.
| *a | Inspection Point |
| CHECK TRANSMITTER BATTERY SAVING FUNCTION |
Check the transmitter battery saving function:
Press the unlock button of the electrical key transmitter sub-assembly twice while pressing the lock button and check that the electrical key transmitter sub-assembly LED blinks 4 times and enters transmitter battery saving mode.
Check that the smart key system does not operate while in transmitter battery saving mode.
| CHECK POWER SOURCE MODE CHANGING FUNCTION |
Check the power switch.
Check that the power source mode changes according to the chart below.
| Shift Position | Brake Pedal | Power Source Mode when Power Switch Pressed |
| P | Released | Off → on (ACC) → on (IG) → off |
| P | Released | On (READY) → off |
| P | Released | On (ACC)* → off |
| P | Depressed | Off → on (READY) |
| P | Depressed | On (ACC) → on (READY) |
| P | Depressed | On (IG) → on (READY) |
| P | Depressed | On (READY) → off |
| P | Depressed | On (ACC)* → off |
| Not P | Released | Off → on (ACC) → on (IG) (after power source mode changes to on (IG), power source mode changes between on (IG) and on (ACC) every time power switch is pressed) |
| Not P | Released | On (READY) → on (ACC) |
| Not P | Depressed | Off → on (IG) |
| Not P | Depressed | On (ACC) → on (IG) |
| Not P | Depressed | On (READY) → on (ACC) |
| CHECK POWER SOURCE MODE INDICATION |
![]() |
Check the smart warning.
| *a | POWER ON display |
| *b | Smart Warning Light display |
| Power Source Mode | Multi-information Display |
| Off (Excluding condition in which the hybrid control system can be started) | Off |
| On (ACC) (Excluding condition in which the hybrid control system can be started) | "POWER ON" displayed |
| On (IG) (Excluding condition in which the hybrid control system can be started) | "POWER ON" displayed |
| Condition in which hybrid control system can be started*1 | Smart Warning Light displayed |
| Hybrid control system started | Off |