Certification ECU Log of ID code registration
Parameter Name
| Detection Condition
| Trouble Area
| Step
|
Failed Registration Mode
| - A registration request was sent while in another mode.
- During registration a different registration request was sent.
| -
| Go to step 3
|
Vehicle ID not set
| A vehicle ID has not been registered in the certification ECU (smart key ECU assembly).
| Certification ECU (smart key ECU assembly)
| Replace certification ECU (smart key ECU assembly) (Click here)
|
Key Registration Max
| A registration request is sent when the maximum number of electrical key transmitter sub-assemblies has already been registered.
| Certification ECU (smart key ECU assembly)
| Go to step 7
|
ID-BOX Error
| A registration request is sent even though whether or not the vehicle is provided with an ID code box is unknown.
| Certification ECU (smart key ECU assembly)
| Check for DTC B2789
|
Vehicle Speed Too High
| A registration request is sent with a vehicle speed of 5 km/h or more.
| -
| Check if the vehicle is stationary. If a code cannot be registered even though the vehicle is stationary, then go to step 4
|
No ECU Response
| The steering lock ECU (steering lock actuator assembly) or ID code box (immobiliser code ECU) was not connected.
| Certification ECU (smart key ECU assembly) Steering lock ECU (steering lock actuator assembly) ID code box (immobiliser code ECU)
| Check for DTC B2785, B2786 or B2789
|
L Code Verification Error
| The L codes registered in the ID code box (immobiliser code ECU) and steering lock ECU (steering lock actuator assembly) did not match.
| ID code box (immobiliser code ECU) Steering lock ECU (steering lock actuator assembly)
| Go to step 5
|
L Code OK S Code NG
| The L code verification was successful but the S code stored in the ID code box (immobiliser code ECU) and certification ECU (smart key ECU assembly) did not match.
| Certification ECU (smart key ECU assembly) ID code box (immobiliser code ECU)
| Go to step 7
|
Key Verification: Max Number
| The number of electrical key transmitter sub-assemblies registered in the ID code box (immobiliser code ECU) was more than 7.
| ID code box (immobiliser code ECU)
| Replace ID code box (immobiliser code ECU) (Click here)
|
Key Verification: Amp Abnormal
| Malfunction of the immobiliser amplifier, such as a short to ground.
| Certification ECU (smart key ECU assembly) Power switch
| Check for DTC B278A or B2784
|
Key Verification: Read Error
| Although a registered electrical key transmitter sub-assembly was held near the power switch, immobiliser system certification did not succeed.
| Certification ECU (smart key ECU assembly) Electrical key transmitter sub-assembly
| Go to step 8
|
Unverified Key
| Although all of the registered electrical key transmitter sub-assemblies had been held near the power switch, electrical key transmitter sub-assembly registration was not possible due to immobiliser system certification not being able to succeed.
| Certification ECU (smart key ECU assembly) Electrical key transmitter sub-assembly
| Go to step 13
|
Transponder Key Amp Error
| Malfunction of the immobiliser amplifier, such as a short to ground.
| Certification ECU (smart key ECU assembly) Power switch
| Check for DTC B278A or B2784
|
New Key Registration Error
| Although an unregistered electrical key transmitter sub-assembly was held near the power switch, electrical key transmitter sub-assembly registration is not possible due to immobiliser system certification not being able to succeed.
| Certification ECU (smart key ECU assembly) Electrical key transmitter sub-assembly Power switch
| Go to step 15
|
New Key Vehicle ID Error
| Although an unregistered electrical key transmitter sub-assembly was held near the power switch, electrical key transmitter sub-assembly registration is not possible due to the vehicle ID not being stored successfully.
| Certification ECU (smart key ECU assembly) Electrical key transmitter sub-assembly
| Go to step 15
|
New Key Registration Failed
| After successful immobiliser system certification, time expired before smart recognition completion confirmation or a registration cancellation request was sent.
| Certification ECU (smart key ECU assembly) Electrical key transmitter sub-assembly
| Go to step 15
|
New Key Already Registered
| Although a registered electrical key transmitter sub-assembly was held near the power switch, time expired or a registration cancellation request was sent.
| -
| Check if a registered electrical key transmitter sub-assembly was held near the power switch instead of an unregistered electrical key transmitter sub-assembly by mistake. Perform registration again using an unregistered electrical key transmitter sub-assembly. If the same problem occurs again, replace the certification ECU (smart key ECU assembly). (Click here)
|
New Key ID Code Error
| Electrical key transmitter sub-assembly registration was not possible due to the certification ECU (smart key ECU assembly) not being able to store the information of the electrical key transmitter sub-assembly to EEPROM correctly.
| Certification ECU (smart key ECU assembly)
| Replace certification ECU (smart key ECU assembly) (Click here)
|
No Response Registering L/S Code
| The certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly) was not connected.
| Certification ECU (smart key ECU assembly) Steering lock ECU (steering lock actuator assembly)
| Check for DTC B2785
|
S Code Verification NG
| The S code could not be stored by the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU).
| Certification ECU (smart key ECU assembly) ID code box (immobiliser code ECU)
| Go to step 7
|
L Code Verification NG
| The L code could not be stored by the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator assembly).
| ID code box (immobiliser code ECU) Steering lock ECU (steering lock actuator assembly)
| Go to step 5
|
ECU ID Verification Error
| Electrical key transmitter sub-assembly registration was not possible due to there being a malfunction in the data send from the ID code box (immobiliser code ECU) to the certification ECU (smart key ECU assembly)
| Certification ECU (smart key ECU assembly) ID code box (immobiliser code ECU)
| Go to step 7
|
Key Number Write Error
| The certification ECU (smart key ECU assembly) could not store the number of electrical key transmitter sub-assemblies to EEPROM.
| Certification ECU (smart key ECU assembly)
| Replace certification ECU (smart key ECU assembly) (Click here)
|
ID Code BOX Write Error
| The certification ECU (smart key ECU assembly) could not store the information of whether or not the ID code box was provided in the vehicle to EEPROM.
| Certification ECU (smart key ECU assembly)
| Replace certification ECU (smart key ECU assembly) (Click here)
|