UPPER INSTRUMENT PANEL > REMOVAL |
| 1. PRECAUTION |
| 2. REMOVE FRONT FLOOR COVER RH |
![]() |
Using a clip remover, remove the 2 clips <A>.
Disengage the 3 clips <B>.
![]() |
Disengage the 3 guides and remove the front floor cover RH.
| 3. DISCONNECT CABLE FROM AUXILIARY BATTERY NEGATIVE TERMINAL |
| 4. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY |
![]() |
Apply protective tape to the area shown in the illustration.
| *1 | Protective Tape |
![]() |
Using a moulding remover, disengage the 8 clips and claw.
Disconnect the connector and remove the center instrument cluster finish panel sub-assembly.
| 5. REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY |
![]() |
Disengage the 3 clips and remove the No. 2 instrument panel register assembly.
| 6. REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH |
![]() |
Apply protective tape to the area shown in the illustration.
| *1 | Protective Tape |
![]() |
Using a moulding remover, disengage the 12 clips and 10 guides to remove the instrument cluster finish panel garnish.
| 7. REMOVE CENTER INSTRUMENT PANEL REGISTER ASSEMBLY |
![]() |
Disengage the claw and 4 clips to remove the center instrument panel register assembly.
| 8. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY |
![]() |
Using a clip remover, remove the 2 clips.
![]() |
Disengage the 4 claws and 9 guides and remove the instrument cluster finish panel sub-assembly.
| 9. REMOVE COMBINATION METER ASSEMBLY |
![]() |
Remove the 2 screws.
![]() |
Disengage the 3 clips as shown in the illustration.
![]() |
Disconnect the 2 connectors.
Disengage the clamp and remove the combination meter assembly.
| 10. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
Disconnect the front door opening trim weatherstrip LH.
| 11. REMOVE FRONT PILLAR GARNISH LH |
![]() |
Pull the upper part of the garnish toward the inside of the cabin and disengage the garnish from the base of the 2 clips.
| *1 | Front Pillar Garnish Clip |
![]() |
Using needle-nose pliers with the tips wrapped with protective tape, rotate the front pillar garnish clip 90° in the direction indicated by the arrow (1) shown in the illustration.
| *a | 90° |
| *b | Protective Tape |
Pull the front pillar garnish LH in the direction indicated by the arrow (2) shown in the illustration to disengage it from the front pillar garnish clip.
Pull the front pillar garnish LH in the direction indicated by the arrow (3) shown in the illustration to disengage the 2 guides to remove the front pillar garnish LH.
![]() |
Protect the curtain shield airbag assembly.
| *1 | Adhesive Tape |
| *2 | Protective Cover |
| *3 | Curtain Shield Airbag Assembly |
Cover the airbag with a piece of cloth or nylon and secure the edges of the cover with tape as shown in the illustration.
| 12. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
Disconnect the front door opening trim weatherstrip RH.
| 13. REMOVE FRONT PILLAR GARNISH RH |
| 14. DISCONNECT NO. 2 INSTRUMENT PANEL WIRE |
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
![]() |
Slide the 2 sliders to release the locks, and then disconnect the 2 connectors.
| *a | Slider |
| 15. REMOVE UPPER INSTRUMENT PANEL ASSEMBLY |
w/ Navigation System:
Disconnect the connector.

Remove the bolt <A>.

| *1 | Bolt <A> | *2 | Screw <C> |
Remove the screw <C>.
Using a clip remover, remove the 2 clips.
Pull the upper instrument panel assembly in the direction indicated by the arrow (1) to disengage the 7 clips.

Pull the upper instrument panel assembly in the direction indicated by the arrow (2) to disengage the 5 guides and remove the upper instrument panel assembly.