Home › Engine / Hybrid System › 1NZ-FXE ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > REMOVAL

for Preparation Click here



1. REMOVE NO. 2 EGR PIPE


    A268229
  1. Disconnect the wire harness clamp.

  1. Disengage the clamp and disconnect the No. 2 water by-pass hose.

  1. Remove the 2 bolts and 2 nuts.

  1. Remove the No. 2 EGR pipe and 2 gaskets.



2. REMOVE EGR COOLER ASSEMBLY


    A267673
  1. Disconnect the 2 connectors and wire harness clamp.



    A267672
  1. Remove the bolt and wire harness clamp bracket.



    A268054
  1. Disconnect the clamp, No. 4 water by-pass hose and No. 5 water by-pass hose.



    A268679
  1. Remove the 2 bolts, nut and EGR valve bracket.



    A268236
  1. Remove the 2 bolts, 2 nuts and EGR valve with cooler assembly.

  1. Remove the gasket.



    A268036
  1. Disconnect the No. 1 water by-pass hose.

  1. Remove the 2 bolts, EGR valve assembly and gasket.



    A268035
  1. Using an E8 "TORX" socket wrench, remove the 2 stud bolts.



3. REMOVE INTAKE MANIFOLD STAY


    A268286
  1. Remove the 2 bolts and intake manifold stay.



4. REMOVE INTAKE MANIFOLD


    A267685
  1. Disconnect the 4 wire harness clamps and water by-pass hose.



    A267684
  1. Disconnect the fuel vapor feed hose and ventilation hose.



    A268526
  1. Remove the 3 bolts, 2 nuts and intake manifold.



    A268531
  1. Remove the ventilation hose.



    A268529
  1. Remove the bolt and intake manifold insulator.



    A268530
  1. Remove the No. 1 intake manifold to head gasket.



5. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR


    A267688
  1. Remove the 3 bolts and No. 1 exhaust manifold heat insulator.



6. REMOVE MANIFOLD SUPPORT BRACKET


    A267692
  1. Remove the 4 bolts and manifold support bracket.



7. REMOVE EXHAUST MANIFOLD


    A268068
  1. Disconnect the wire harness clamp and oxygen sensor connector.



    A267694
  1. Remove the 3 bolts, 2 nuts and exhaust manifold.

  1. Remove the exhaust manifold to head gasket.



8. REMOVE NO. 4 WATER BY-PASS HOSE


    A266947
  1. Disconnect the No. 4 water by-pass hose.

  1. Remove the bolt and No. 4 water by-pass hose.



9. REMOVE NO. 1 WATER BY-PASS PIPE


    A266949
  1. Disconnect the water hose from the water inlet with thermostat sub-assembly.

  1. Remove the 3 bolts and No. 1 water by-pass pipe.



10. REMOVE WIRE HARNESS CLAMP BRACKET


    A268019
  1. Remove the bolt and wire harness clamp bracket.



11. REMOVE STUD BOLT


    A275627
  1. Using an E7 "TORX" socket wrench, remove the stud bolt.



12. REMOVE ENGINE OIL LEVEL DIPSTICK
  1. Remove the engine oil level dipstick.



13. REMOVE IGNITION COIL ASSEMBLY


    A267419
  1. Disconnect the 4 No. 1 ignition coil connectors.

  1. Remove the 4 bolts and 4 No. 1 ignition coils.

    NOTICE:
    When removing each ignition coil, do not damage the plug cap on the engine head cover opening or the upper edge of the spark plug tube.