HYBRID CONTROL SYSTEM > TERMINALS OF ECU |

| *1 | Power Management Control ECU | - | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| A38-2 (+B2) - G57-6 (E1) | L - BR | Power source | Ignition switch ON (IG) | 11 to 14 V |
| A38-11 (VLO) - G57-6 (E1) | R - BR | DC/DC operation monitor / voltage change signal | Ignition switch ON (IG) | Pulse generation (Waveform 1) |
| A38-13 (IWP) - G57-6 (E1) | G - BR | Inverter water pump assembly signal | Ignition switch ON (READY) | Pulse generation (Waveform 2) |
| A38-14 (NIWP) - G57-6 (E1) | P - BR | Inverter water pump assembly signal | Ignition switch ON (READY) | Pulse generation (Waveform 2) |
| A38-15 (BL) - G57-6 (E1) | R - BR | Back up light | Ignition switch ON (IG), shift lever in R | 11 to 14 V |
| A38-19 (CLK) - G57-6 (E1) | G - BR | A/C communication signal | Ignition switch ON (READY), air conditioning system stopped | Pulse generation (Waveform 3) |
| A38-20 (STB) - G57-6 (E1) | W - BR | A/C communication signal | Ignition switch ON (READY), air conditioning system stopped | Pulse generation (Waveform 3) |
| A38-21 (NODD) - G57-6 (E1) | W - BR | DC/DC operation | DC/DC converter operating normally | 5 to 7 V |
| DC/DC converter not operating normally | 2 to 4 V | |||
| DC/DC converter operating prohibited | 0.1 to 0.5 V | |||
| A38-24 (MMT) - A38-25 (MMTG) | L - BR | Motor temperature sensor | Ignition switch ON (IG), temperature 25°C (77°F) | 3.6 to 4.6 V |
| Ignition switch ON (IG), temperature 60°C (140°F) | 2.2 to 3.2 V | |||
| A38-26 (GMT) - A38-27 (GMTG) | B - R | Generator temperature sensor | Ignition switch ON (IG), temperature 25°C (77°F) | 3.6 to 4.6 V |
| Ignition switch ON (IG), temperature 60°C (140°F) | 2.2 to 3.2 V | |||
| A38-29 (SI0) - G57-6 (E1) | Y - BR | HV battery blower fan operation signal | Ignition switch ON (IG), during Active Test | Pulse generation (Waveform 4) |
| A38-30 (ETI) - G57-6 (E1) | R - BR | A/C communication signal | Ignition switch ON (READY), air conditioning system stopped | Pulse generation (Waveform 3) |
| A38-31 (ITE) - G57-6 (E1) | Y - BR | A/C communication signal | Ignition switch ON (READY), air conditioning system stopped | Pulse generation (Waveform 3) |
| A38-32 (ILK) - G57-6 (E1) | V - BR | Interlock switch | Ignition switch ON (IG), inverter terminal cover, high-voltage input cables and service plug grip installed correctly | 0 to 1.5 V |
| Ignition switch ON (IG), inverter terminal cover, high-voltage input cables or service plug grip not installed | 11 to 14 V | |||
| A39-1 (IG2) - G57-6 (E1) | P - BR | Power source | Ignition switch ON (IG) | 11 to 14 V |
| A39-2 (IG2D) - G57-6 (E1) | P - BR | IG2 relay | Ignition switch ON (IG) | 11 to 14 V |
| A39-5 (+B1) - G57-6 (E1) | L - BR | Power source | Ignition switch ON (IG) | 11 to 14 V |
| A39-6 (MREL) - G57-6 (E1) | BE - BR | Main relay | Ignition switch ON (IG) | 11 to 14 V |
| A39-7 (ST1-) - G57-6 (E1) | BR - BR | Brake cancel switch | Ignition switch ON (IG), brake pedal depressed | 0 to 1.5 V |
| Ignition switch ON (IG), brake pedal released | 11 to 14 V | |||
| A39-8 (N) - G57-6 (E1) | Y - BR | Shift lever position signal | Ignition switch ON (IG), shift lever in N | 11 to 14 V |
| Ignition switch ON (IG), shift lever not in N | 0.5 to 1.5 V | |||
| A39-9 (PR) - G57-6 (E1) | V - BR | Shift lever position signal | Ignition switch ON (IG), shift lever in P or R | 11 to 14 V |
| Ignition switch ON (IG), shift lever not in P or R | 0.5 to 1.5 V | |||
| A39-11 (DB1) - G57-6 (E1) | L - BR | Shift lever position signal | Ignition switch ON (IG), shift lever in D or B | 11 to 14 V |
| Ignition switch ON (IG), shift lever not in D or B | 0.5 to 1.5 V | |||
| A39-13 (DB2) - G57-6 (E1) | B - BR | Shift lever position signal | Ignition switch ON (IG), shift lever in D or B | 11 to 14 V |
| Ignition switch ON (IG), shift lever not in D or B | 0.5 to 1.5 V | |||
| A39-14 (R) - G57-6 (E1) | SB - BR | Shift lever position signal | Ignition switch ON (IG), shift lever in R | 11 to 14 V |
| Ignition switch ON (IG), shift lever not in R | 0.5 to 1.5 V | |||
| A39-15 (P) - G57-6 (E1) | BE - BR | Shift lever position signal | Ignition switch ON (IG), shift lever in P | 11 to 14 V |
| Ignition switch ON (IG), shift lever not in P | 0.5 to 1.5 V | |||
| A39-16 (PNB) - G57-6 (E1) | G - BR | Shift lever position signal | Ignition switch ON (IG), shift lever in P, N or B | 11 to 14 V |
| A39-18 (VCP1) - A39-34 (EP1) | Y - B | Accelerator pedal sensor assembly power source (for VPA1) | Ignition switch ON (IG) | 4.5 to 5.5 V |
| A39-19 (VCP2) - A39-35 (EP2) | G - R | Accelerator pedal sensor assembly power source (for VPA2) | Ignition switch ON (IG) | 4.5 to 5.5 V |
| A39-20 (CLK-) - G57-6 (E1) | W - BR | MG communication clock signal | Ignition switch ON (READY) | Pulse generation (Waveform 5) |
| A39-21 (CLK+) - G57-6 (E1) | B - BR | MG communication clock signal | Ignition switch ON (READY) | Pulse generation (Waveform 5) |
| A39-23 (STP) - G57-6 (E1) | L - BR | Stop light switch | Brake pedal depressed | 11 to 14 V |
| Brake pedal released | 0 to 1.5 V | |||
| A39-24 (HTM+) - G57-6 (E1) | B - BR | Communication signal from power management control ECU to MG ECU | Ignition switch ON (IG) | Pulse generation (Waveform 6) |
| A39-25 (HTM-) - G57-6 (E1) | W - BR | Communication signal from power management control ECU to MG ECU | Ignition switch ON (IG) | Pulse generation (Waveform 6) |
| A39-26 (VPA1) - A39-34 (EP1) | L - B | Accelerator pedal sensor assembly (for accelerator pedal position detection) | Ignition switch ON (IG), accelerator pedal released | 0.4 to 1.4 V |
| Ignition switch ON (IG) engine stopped, shift lever in P accelerator pedal fully depressed | 2.6 to 4.5 V | |||
| A39-27 (VPA2) - A39-35 (EP2) | W - R | Accelerator pedal sensor assembly (for accelerator pedal position detection) | Ignition switch ON (IG), accelerator pedal released | 1.0 to 2.2 V |
| Ignition switch ON (IG) engine stopped, shift lever in P accelerator pedal fully depressed | 3.4 to 5.3 V | |||
| A39-29 (MTH-) - G57-6 (E1) | W - BR | Communication signal from MG ECU to power management control ECU | Ignition switch ON (IG) | Pulse generation (Waveform 7) |
| A39-30 (MTH+) - G57-6 (E1) | B - BR | Communication signal from MG ECU to power management control ECU | Ignition switch ON (IG) | Pulse generation (Waveform 7) |
| A39-31 (HSDN) - G57-6 (E1) | B - BR | MG ECU shutdown signal | Ignition switch ON (READY) | 0 to 1.5 V |
| A39-32 (REQ-) - G57-6 (E1) | W - BR | MG ECU communication request signal | Ignition switch ON (IG) | Pulse generation (Waveform 8) |
| A39-33 (REQ+) - G57-6 (E1) | B - BR | MG ECU communication request signal | Ignition switch ON (IG) | Pulse generation (Waveform 8) |
| G57-1 (AM22)*1 - G57-6 (E1) | B - BR | Constant power source | Power switch on (IG) | 11 to 14 V |
| Power switch on (READY) | 11 to 15.5 V | |||
| G57-1 (BATT)*2 - G57-6 (E1) | BE - BR | Constant power source | Ignition switch ON (IG) | 11 to 14 V |
| Ignition switch ON (READY) | 11 to 15.5 V | |||
| G57-2 (SMRG) - G57-5 (E01) | Y - W-B | System main relay operation signal | Ignition switch ON (IG)→Ignition switch ON (READY) | Pulse generation (Waveform 9) |
| G57-3 (SMRP) - G57-5 (E01) | W - W-B | System main relay operation signal | Ignition switch ON (IG)→Ignition switch ON (READY) | Pulse generation (Waveform 9) |
| G57-4 (SMRB) - G57-5 (E01) | SB - W-B | System main relay operation signal | Ignition switch ON (IG)→Ignition switch ON (READY) | Pulse generation (Waveform 9) |
| G57-7 (SSW1)*1 - G57-6 (E1) | V - BR | Power switch | Power switch pressed and held | 0 to 1.5 V |
| G57-11 (TC) - G57-6 (E1) | V - BR | Diagnosis terminal | Ignition switch ON (IG) | 11 to 14 V |
| G57-13 (EVSW) - G57-6 (E1) | B - BR | EV switch signal | Ignition switch ON (IG), EV switch not operated | 11 to 14 V |
| Ignition switch ON (IG), EV switch operated | 0 to 1.5 V | |||
| G57-14 (SPDI) - G57-6 (E1) | SB - BR | Vehicle speed signal | Driving at approximately 20 km/h (12 mph) with ignition switch ON (READY) | Pulse generation (Waveform 10) |
| G57-15 (P2) - G57-6 (E1) | G - BR | Shift P signal | Ignition switch ON (IG) | Pulse generation (Waveform 11) |
| G57-28 (THB) - G57-30 (ETHB) | L - V | Auxiliary battery temperature | Ignition switch ON (IG), auxiliary battery temperature 25°C (77°F) | 1.7 to 2.3 V |
| Ignition switch ON (IG), auxiliary battery temperature 60°C (140°F) | 0.6 to 0.9 V | |||
| G57-29 (ABFS) - G57-6 (E1) | R - BR | Airbag activation signal | Ignition switch ON (READY) | Pulse generation (Waveform 12) |
| G57-32 (BTH+) - G57-6 (E1) | R - BR | Communication signal from battery smart unit to power management control ECU | Ignition switch ON (IG) | Pulse generation (Waveform 13) |
| G57-33 (BTH-) - G57-6 (E1) | G - BR | Communication signal from battery smart unit to power management control ECU | Ignition switch ON (IG) | Pulse generation (Waveform 13) |
| G58-1 (ACCD)*1 - G57-6 (E1) | L - BR | ACC relay | Power switch on (ACC) | 11 to 14 V |
| G58-2 (IG1D)*1 - G57-6 (E1) | SB - BR | IG1 relay | Power switch on (IG) | 11 to 14 V |
| G58-7 (AM21)*1 - G57-6 (E1) | B - BR | Constant power source | Power switch on (IG) | 11 to 14 V |
| Power switch ON (READY) | 11 to 15.5 V | |||
| G58-11 (LIN2)*1 - G57-6 (E1) | LG - BR | LIN communication signal | Power switch on (IG) | Pulse generation |
| G58-17 (SSW2)*1 - G57-6 (E1) | SB - BR | Power switch | Power switch pressed and held | 0 to 1.5 V |
| G58-24 (CA1L) - G57-6 (E1) | W - BR | CAN communication signal | Ignition switch ON (IG) | Pulse generation (Waveform 14) |
| G58-25 (CA1H) - G57-6 (E1) | BE - BR | CAN communication signal | Ignition switch ON (IG) | Pulse generation (Waveform 14) |
| G58-30 (CA3N) - G57-6 (E1) | W - BR | CAN communication signal | Ignition switch ON (IG) | Pulse generation (Waveform 15) |
| G58-31 (CA3P) - G57-6 (E1) | R - BR | CAN communication signal | Ignition switch ON (IG) | Pulse generation (Waveform 15) |
| Oscilloscope waveforms |
![]() |
Waveform 1 (DC/DC operation monitor / voltage change signal)
| Item | Content |
| Terminal | A38-11 (VLO) - G57-6 (E1) |
| Equipment Setting | 5 V/DIV., 50 ms./DIV. |
| Condition | Ignition switch ON (IG) |
![]() |
Waveform 2 (Inverter water pump assembly signal)
| Item | Content |
| Terminal | CH1: A38-13 (IWP) - G57-6 (E1) CH2: A38-14 (NIWP) - G57-6 (E1) |
| Equipment Setting | 5 V/DIV., 50 ms./DIV. |
| Condition | Ignition switch ON (READY) |
![]() |
Waveform 3 (A/C communication signal)
| Item | Content |
| Terminal | CH1: A38-19 (CLK) - G57-6 (E1) CH2: A38-31 (ITE) - G57-6 (E1) CH3: A38-30 (ETI) - G57-6 (E1) CH4: A38-20 (STB) - G57-6 (E1) |
| Equipment Setting | 10 V/DIV., 100 ms./DIV. |
| Condition | Ignition switch ON (READY), air conditioning system stopped |
![]() |
Waveform 4 (HV battery blower fan operation signal)
| Item | Content |
| Terminal | A38-29 (SI0) - G57-6 (E1) |
| Equipment Setting | 5 V/DIV., 500 ms./DIV. |
| Condition | Ignition switch ON (IG), during Active Test |
![]() |
Waveform 5 (MG communication clock signal)
| Item | Content |
| Terminal | CH1: A39-21 (CLK+) - G57-6 (E1) CH2: A39-20 (CLK-) - G57-6 (E1) |
| Equipment Setting | 1 V/DIV., 1 μs./DIV. |
| Condition | Ignition switch ON (READY) |
![]() |
Waveform 6 (communication signal from power management control ECU to MG ECU)
| Item | Content |
| Terminal | CH1: A39-24 (HTM+) - G57-6 (E1) CH2: A39-25 (HTM-) - G57-6 (E1) |
| Equipment Setting | 1 V/DIV., 200 μs./DIV. |
| Condition | Ignition switch ON (IG) |
![]() |
Waveform 7 (communication signal from MG ECU to power management control ECU)
| Item | Content |
| Terminal | CH1: A39-30 (MTH+) - G57-6 (E1) CH2: A39-29 (MTH-) - G57-6 (E1) |
| Equipment Setting | 1 V/DIV., 200 μs./DIV. |
| Condition | Ignition switch ON (IG) |
![]() |
Waveform 8 (MG ECU communication request signal)
| Item | Content |
| Terminal | CH1: A39-33 (REQ+) - G57-6 (E1) CH2: A39-32 (REQ-) - G57-6 (E1) |
| Equipment Setting | 1 V/DIV., 1 ms./DIV. |
| Condition | Ignition switch ON (IG) |
![]() |
Waveform 9 (system main relay operation signal)
| Item | Content |
| Terminal | CH1: G57-3 (SMRP) - G57-5 (E01) CH2: G57-4 (SMRB) - G57-5 (E01) CH3: G57-2 (SMRG) - G57-5 (E01) |
| Equipment Setting | 10 V/DIV., 200 ms./DIV. |
| Condition | Ignition switch ON (IG) → Ignition switch ON (READY) |
![]() |
Waveform 10 (vehicle speed signal)
| Item | Content |
| Terminal | G57-14 (SPDI) - G57-6 (E1) |
| Equipment Setting | 5 V/DIV., 20 ms./DIV. |
| Condition | Driving at approximately 20 km/h (12 mph) with ignition switch ON (READY) |
![]() |
Waveform 11 (shift P signal)
| Item | Content |
| Terminal | G57-15 (P2) - G57-6 (E1) |
| Equipment Setting | 5 V/DIV., 10 ms./DIV. |
| Condition | Ignition switch ON (IG) |
![]() |
Waveform 12 (airbag activation signal)
| Item | Content |
| Terminal | G57-29 (ABFS) - G57-6 (E1) |
| Equipment Setting | 5 V/DIV., 500 ms./DIV. |
| Condition | Ignition switch ON (READY) |
![]() |
Waveform 13 (communication signal from battery smart unit to power management control ECU)
| Item | Content |
| Terminal | CH1: G57-32 (BTH+) - G57-6 (E1) CH2: G57-33 (BTH-) - G57-6 (E1) |
| Equipment Setting | 2 V/DIV., 500 μs./DIV. |
| Condition | Ignition switch ON (IG) |
![]() |
Waveform 14 (CAN communication signal)
| Item | Content |
| Terminal | CH1: G58-25 (CA1H) - G57-6 (E1) CH2: G58-24 (CA1L) - G57-6 (E1) |
| Equipment Setting | 1 V/DIV., 50 μs./DIV. |
| Condition | Ignition switch ON (IG) |
![]() |
Waveform 15 (CAN communication signal)
| Item | Content |
| Terminal | CH1: G58-31 (CA3P) - G57-6 (E1) CH2: G58-30 (CA3N) - G57-6 (E1) |
| Equipment Setting | 1 V/DIV., 50 μs./DIV. |
| Condition | Ignition switch ON (IG) |

| *1 | Inverter with Converter Assembly | - | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Standard Condition |
| A47-1 (IGCT) - A47-28 (GND1) | B - W | MG ECU power source | Ignition switch ON (IG) | 11 to 14 V |
| A47-2 (IDH) - A47-28 (GND1) | L - W | PTC heater prohibit signal | Ignition switch ON (IG) | 4 to 6 V |
| A47-3 (VLO) - A47-28 (GND1) | R - W | DC/DC operation monitor / voltage change signal | Ignition switch ON (IG) | Pulse generation (Waveform 1) |
| A47-5 (CLK+) - A47-28 (GND1) | B - W | MG ECU communication clock signal | Ignition switch ON (READY) | Pulse generation (Waveform 2) |
| A47-6 (REQ+) - A47-28 (GND1) | B - W | MG ECU communication request signal | Ignition switch ON (READY) | Pulse generation (Waveform 3) |
| A47-7 (MTH+) - A47-28 (GND1) | B - W | Communication signal from MG ECU to power management control ECU | Ignition switch ON (READY) | Pulse generation (Waveform 4) |
| A47-8 (HTM+) - A47-28 (GND1) | B - W | Communication signal from power management control ECU to MG ECU | Ignition switch ON (READY) | Pulse generation (Waveform 5) |
| A47-9 (+B2) - A47-28 (GND1) | G - W | MG ECU power source | Ignition switch ON (IG) | 11 to 14 V |
| A47-10 (+B) - A47-28 (GND1) | G - W | MG ECU power source | Ignition switch ON (IG) | 11 to 14 V |
| A47-12 (NODD) - A47-28 (GND1) | W - W | DC/DC operation | DC/DC converter operating normally | 5 to 7 V |
| DC/DC converter not operating normally | 2 to 4 V | |||
| DC/DC converter operation prohibited | 0.1 to 0.5 V | |||
| A47-15 (CLK-) - A47-28 (GND1) | W - W | MG ECU communication clock signal | Ignition switch ON (READY) | Pulse generation (Waveform 2) |
| A47-16 (REQ-) - A47-28 (GND1) | W - W | MG ECU communication request signal | Ignition switch ON (READY) | Pulse generation (Waveform 3) |
| A47-17 (MTH-) - A47-28 (GND1) | W - W | Communication signal from MG ECU to power management control ECU | Ignition switch ON (READY) | Pulse generation (Waveform 4) |
| A47-18 (HTM-) - A47-28 (GND1) | W - W | Communication signal from power management control ECU to MG ECU | Ignition switch ON (READY) | Pulse generation (Waveform 5) |
| A47-29 (GI) - A47-28 (GND1) | B - W | Camshaft position sensor signal | Ignition switch ON (READY), with engine running | Pulse generation (Waveform 6) |
| A47-31 (HSDN) - A47-28 (GND1) | B - W | MG shutdown signal | Ignition switch ON (READY) | 0 to 1 V |
| A47-35 (ILKI) - A47-28 (GND1) | V - W | Interlock switch signal | Ignition switch ON (IG), inverter terminal cover, high-voltage input cables and service plug grip installed correctly | Below 1 V |
| Ignition switch ON (IG), inverter terminal cover, high-voltage input cables or service plug grip not installed | 11 to 14 | |||
| A47-36 (ILKO) - A47-28 (GND1) | LG - W | Interlock switch signal | Ignition switch ON (IG), inverter terminal cover, high-voltage input cables and service plug grip installed correctly | Below 1 V |
| Ignition switch ON (IG), inverter terminal cover, high-voltage input cables or service plug grip not installed | 11 to 14 | |||
| C28-1 (MRF) - C28-2 (MRFG) | BR - G | Motor resolver signal | Motor resolver running | Pulse generation (Waveform 7) |
| C28-3 (MSN) - C28-4 (MSNG) | L - R | Motor resolver signal | Motor resolver running | Pulse generation (Waveform 7) |
| C28-6 (MCS) - C28-5 (MCSG) | W - Y | Motor resolver signal | Motor resolver running | Pulse generation (Waveform 7) |
| C28-7 (GSN) - C28-8 (GSNG) | L - R | Generator resolver signal | Generator resolver running | Pulse generation (Waveform 8) |
| C28-10 (GCS) - C28-9 (GCSG) | W - Y | Generator resolver signal | Generator resolver running | Pulse generation (Waveform 8) |
| C28-11 (GRF) - C28-12 (GRFG) | BR - G | Generator resolver signal | Generator resolver running | Pulse generation (Waveform 8) |
| Oscilloscope waveforms |
![]() |
Waveform 1 (DC/DC operation monitor / voltage change signal)
| Item | Content |
| Terminal | A47-3 (VLO) - A47-28 (GND1) |
| Equipment Setting | 5 V/DIV., 50 ms./DIV. |
| Condition | Ignition switch ON (IG) |
![]() |
Waveform 2 (MG ECU communication clock signal)
| Item | Content |
| Terminal | CH1: A47-5 (CLK+) - A47-28 (GND1) CH2: A47-15 (CLK-) - A47-28 (GND1) |
| Equipment Setting | 1 V/DIV., 1 μs./DIV. |
| Condition | Ignition switch ON (READY) |
![]() |
Waveform 3 (MG ECU communication request signal)
| Item | Content |
| Terminal | CH1: A47-6 (REQ+) - A47-28 (GND1) CH2: A47-16 (REQ-) - A47-28 (GND1) |
| Equipment Setting | 1 V/DIV., 1 ms./DIV. |
| Condition | Ignition switch ON (READY) |
![]() |
Waveform 4 (communication signal from MG ECU to power management control ECU)
| Item | Content |
| Terminal | CH1: A47-7 (MTH+) - A47-28 (GND1) CH2: A47-17 (MTH-) - A47-28 (GND1) |
| Equipment Setting | 1 V/DIV., 200 μs./DIV. |
| Condition | Ignition switch ON (READY) |
![]() |
Waveform 5 (communication signal from power management control ECU to MG ECU)
| Item | Content |
| Terminal | CH1: A47-8 (HTM+) - A47-28 (GND1) CH2: A47-18 (HTM-) - A47-28 (GND1) |
| Equipment Setting | 1 V/DIV., 200 μs./DIV. |
| Condition | Ignition switch ON (READY) |
![]() |
Waveform 6 (Camshaft position sensor signal)
| Item | Content |
| Terminal | A47-29 (GI) - A47-28 (GND1) |
| Equipment Setting | 5 V/DIV., 20 ms./DIV. |
| Condition | Ignition switch ON (READY), with engine running |
![]() |
Waveform 7 (motor resolver signal)
| Item | Content |
| Terminal | CH1: C28-1 (MRF) - C28-2 (MRFG) CH2: C28-3 (MSN) - C28-4 (MSNG) CH3: C28-6 (MCS) - C28-5 (MCSG) |
| Equipment Setting | CH1: 10 V/DIV., 1 ms./DIV. CH2, 3: 5 V/DIV., 1 ms./DIV. |
| Condition | Motor resolver running |
![]() |
Waveform 8 (generator resolver signal)
| Item | Content |
| Terminal | CH1: C28-11 (GRF) - C28-12 (GRFG) CH2: C28-7 (GSN) - C28-8 (GSNG) CH3: C28-10 (GCS) - C28-9 (GCSG) |
| Equipment Setting | CH1: 10 V/DIV., 1 ms./DIV. CH2, 3: 5 V/DIV., 1 ms./DIV. |
| Condition | Generator resolver running |