DTC P3000-389 Battery Control System |
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
| P3000 | 389 | Malfunction is received from the battery voltage sensor Voltage of a battery block drops drastically. (1 trip detection logic) |
|
| DTC No. | Data List |
| P3000-389 |
|
| 1.CHECK DTC OUTPUT (HYBRID CONTROL) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check if DTCs are output.
| Result | Proceed to |
| P3000-389 or P3000-388 only is output. | A |
| DTCs other than P3000-389 and P3000-388 are also output. | B |
Turn the ignition switch off.
|
| ||||
| A | |
| 2.CHECK DTC OUTPUT (ENGINE AND ECT) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (IG).
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Check if DTCs are output.
| Result | Proceed to |
| No DTCs are output. | A |
| DTCs are output. | B |
Turn the ignition switch off.
|
| ||||
| A | |
| 3.CHECK ENGINE START |
Turn the ignition switch to ON (READY).
Check if the engine starts.
| Result | Proceed to |
| The engine does not start. | A |
| The engine starts. | B |
Turn the ignition switch off.
|
| ||||
| A | |
| 4.CHECK CRANKSHAFT PULLEY REVOLUTION (P POSITION) |
With the shift lever in P and lift up the vehicle.
Turn the crankshaft pulley using hand tools to check if the crankshaft can rotate smoothly.
| Result | Proceed to |
| The crankshaft rotates smoothly. | A |
| The crankshaft does not rotate smoothly. | B |
Lower the vehicle.
|
| ||||
| A | |
| 5.CHECK HV BATTERY |
Turn the ignition switch off.
Wait 10 minutes or more.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Battery Block Vol -V01 to 10.
Read the Data List.
| Result | Proceed to |
| One or more battery block voltages are below 12.0 V. | A |
| All battery block voltages are 12.0 V or more. | B |
Turn the ignition switch off.
|
| ||||
| A | ||
| ||
| 6.CHECK CRANKSHAFT PULLEY REVOLUTION (N POSITION) |
Turn the ignition switch to ON (IG).
Move the shift lever to N and lift up the vehicle.
Turn the crankshaft pulley using hand tools to check if the crankshaft can rotate smoothly.
| Result | Proceed to |
| The crankshaft does not rotate smoothly. | A |
| The crankshaft rotates smoothly. | B |
Lower the vehicle.
|
| ||||
| A | |
| 7.REPAIR OR REPLACE ENGINE |
| NEXT | |
| 8.CHECK ENGINE START |
Turn the ignition switch to ON (READY).
Check if the engine starts.
| Result | Proceed to |
| The engine does not start. | A |
| The engine starts. | B |
Turn the ignition switch off.
|
| ||||
| A | |
| 9.CHECK HV BATTERY |
Turn the ignition switch off.
Wait 10 minutes or more.
Turn the ignition switch to ON (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Battery Block Vol -V01 to 10.
Read the Data List.
| Result | Proceed to |
| One or more battery block voltages are below 12.0 V. | A |
| All battery block voltages are 12.0 V or more. | B |
Turn the ignition switch off.
|
| ||||
| A | ||
| ||
| 10.REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY |
| NEXT | |
| 11.CHECK ENGINE START |
Turn the ignition switch to ON (READY).
Check if the engine starts.
| Result | Proceed to |
| The engine does not start. | A |
| The engine starts. | B |
Turn the ignition switch off.
|
| ||||
| A | |
| 12.CHECK HV BATTERY |
Wait 10 minutes or more.
Turn the ignition switch to ON (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Battery Block Vol -V01 to 10.
Read the Data List.
| Result | Proceed to |
| One or more battery block voltages are below 12.0 V. | A |
| All battery block voltages are 12.0 V or more. | B |
Turn the ignition switch off.
|
| ||||
| A | ||
| ||