Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P3108-536    Lost Communication with A/C System Control Module

for Preparation Click here


DESCRIPTION

  1. The power management control ECU detects a wiring malfunction in the serial communication line between it and the compressor with motor assembly.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P3108
536
Communication error (air conditioning system to hybrid control system).
Error in communication data from the A/C inverter.
Although an air conditioning inverter shutdown signal is sent, the air conditioning inverter does not shutdown.
(1 trip detection logic)
  1. Wire harness or connector
  2. Compressor with motor assembly
  3. Power management control ECU

Related Data List 
DTC No.
Data List
P3108-536
  1. A/C Consumption Pwr
  2. Aircon Gate Status

WIRING DIAGRAM


A254877E10


INSPECTION PROCEDURE

HINT:
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
  1. Wait for 30 seconds or more with the ignition switch ON (READY) and the air conditioning turned off.
  2. Turn the air conditioning on and wait for 30 seconds or more.

1.CHECK DTC OUTPUT (AIR CONDITIONER)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (READY).

  1. Enter the following menus: Body Electrical / Air Conditioner / Trouble Codes.

  1. Check if DTCs related to the air conditioning system (A/ C) are output.

    Result:
    Result
    Proceed to
    DTCs related to A/C are not output.
    A
    DTCs related to A/C are output.
    B

  1. Turn the ignition switch off.



B
GO TO DTC CHART (AIR CONDITIONING SYSTEM)
A


2.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)


    A269501
  1. Check the connector connections and contact pressure of the relevant terminals for the power management control ECU connectors (Click here).

    OK:
    The connectors are connected securely and there are no contact pressure problems.



NG
CONNECT SECURELY
OK


3.CHECK CONNECTOR CONNECTION CONDITION (COMPRESSOR WITH MOTOR ASSEMBLY CONNECTOR)


    A267470E01
  1. Check the connection of connector C22 of the compressor with motor assembly.

    OK:
    The connector is connected securely and there are no contact problems.



NG
CONNECT SECURELY
OK


4.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY POWER SOURCE CIRCUIT)
  1. Disconnect connector C22 from the compressor with motor assembly.



    A211448E26
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    C22-5 (GND) - Body ground
    Ignition switch off
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Compressor with Motor Assembly)

  1. Turn the ignition switch to ON (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C22-6 (IG1) - C22-5 (GND)
    Ignition switch ON (IG)
    11 to 14 V

    NOTICE:
    Turning the ignition switch to ON (IG) with the compressor with motor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

  1. Turn the ignition switch off.

  1. Connect the compressor with motor assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - COMPRESSOR WITH MOTOR ASSEMBLY)
  1. Disconnect connector A38 from the power management control ECU.

  1. Disconnect connector C22 from the compressor with motor assembly.

  1. Turn the ignition switch to ON (IG).



    A206712E31
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A38-19 (CLK) - Body ground
    Ignition switch ON (IG)
    Below 1 V
    A38-20 (STB) - Body ground
    Ignition switch ON (IG)
    Below 1 V
    A38-30 (ETI) - Body ground
    Ignition switch ON (IG)
    Below 1 V
    A38-31 (ITE) - Body ground
    Ignition switch ON (IG)
    Below 1 V

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)
    *b
    Front view of wire harness connector
    (to Compressor with Motor Assembly)

    NOTICE:
    Turning the ignition switch to ON (IG) with the power management control ECU connector and the compressor with motor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    A38-19 (CLK) - C22-1 (CLK)
    Ignition switch off
    Below 1 Ω
    A38-20 (STB) - C22-4 (STBI)
    Ignition switch off
    Below 1 Ω
    A38-30 (ETI) - C22-3 (DOUT)
    Ignition switch off
    Below 1 Ω
    A38-31 (ITE) - C22-2 (DIN)
    Ignition switch off
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Switch Condition
    Specified Condition
    A38-19 (CLK) or C22-1 (CLK) - Body ground and other terminals
    Ignition switch off
    10 kΩ or higher
    A38-20 (STB) or C22-4 (STBI) - Body ground and other terminals
    Ignition switch off
    10 kΩ or higher
    A38-30 (ETI) or C22-3 (DOUT) - Body ground and other terminals
    Ignition switch off
    10 kΩ or higher
    A38-31 (ITE) or C22-2 (DIN) - Body ground and other terminals
    Ignition switch off
    10 kΩ or higher

  1. Connect the compressor with motor assembly connector.

  1. Connect the power management control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK POWER MANAGEMENT CONTROL ECU
  1. Disconnect connector C22 from the compressor with motor assembly.



    A211448E45
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    C22-3 (DOUT) - Body ground
    Ignition switch off
    10 kΩ or higher
    C22-4 (STBI) - Body ground
    Ignition switch off
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Compressor with Motor Assembly)

  1. Turn the ignition switch to ON (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C22-1 (CLK) - Body ground
    Ignition switch ON (IG)
    11 to 14 V
    C22-2 (DIN) - Body ground
    Ignition switch ON (IG)
    11 to 14 V
    C22-3 (DOUT) - Body ground
    Ignition switch ON (IG)
    Below 1 V
    C22-4 (STBI) - Body ground
    Ignition switch ON (IG)
    Below 1 V

    NOTICE:
    Turning the ignition switch to ON (IG) with the compressor with motor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

  1. Turn the ignition switch off.

  1. Connect the compressor with motor assembly connector.



NG
REPLACE POWER MANAGEMENT CONTROL ECU (Click here)
OK


7.CHECK COMPRESSOR WITH MOTOR ASSEMBLY
  1. Disconnect connector A38 from the power management control ECU.



    A204443E48
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A38-19 (CLK) - Body ground
    Ignition switch off
    10 kΩ or higher
    A38-31 (ITE) - Body ground
    Ignition switch off
    10 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)

  1. Turn the ignition switch to ON (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A38-20 (STB) - Body ground
    Ignition switch ON (IG)
    11 to 14 V
    A38-30 (ETI) - Body ground
    Ignition switch ON (IG)
    11 to 14 V
    A38-19 (CLK) - Body ground
    Ignition switch ON (IG)
    Below 1 V
    A38-31 (ITE) - Body ground
    Ignition switch ON (IG)
    Below 1 V

    NOTICE:
    Turning the ignition switch to ON (IG) with the power management control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

  1. Turn the ignition switch off.

  1. Connect the power management control ECU connector.



NG
REPLACE COMPRESSOR WITH MOTOR ASSEMBLY (Click here)
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)