ENGINE UNIT > GENERAL



OUTLINE
  1. The 2ZR-FXE is an in-line 4-cylinder, 1.8-liter, 16-valve DOHC engine.



  2. This engine uses a high-expansion ratio Atkinson cycle, VVT-i (Variable Valve Timing-intelligent) system, ETCS-i (Electronic Throttle Control System-intelligent), and EGR system* employing a highly efficient EGR cooler. In addition, use of an engine water pump assembly has eliminated the V-ribbed belt. Thus, improved engine performance, quietness, fuel economy, and cleaner emissions have been achieved.

    HINT:
    *: Models with EGR system


    W101520E03


    W100097E01


MAJOR DIFFERENCE
  1. The new models have been modified from the previous models as shown below:

    1. Due to the addition of the E25 model, which uses fuel with an ethanol concentration of 25%, the EGR system has been discontinued on the engine for E25 models.


SPECIFICATION

Engine Type
2ZR-FXE
No. of Cyls. and Arrangement
4-cylinder, In-line
Valve Mechanism
16-valve DOHC, Chain Drive (with VVT-i)
Combustion Chamber
Pentroof Type
Flow of Intake and Exhaust Gasses
Cross-flow
Fuel System
SFI
Ignition System
DIS
Displacement
1798 cm3 (109.7 cu. in.)
Bore x Stroke
80.5 mm X 88.3 mm (3.17 in. X 3.48 in.)
Compression Ratio
13.0:1
Max. Output
(EEC)
73 kW @ 5200 rpm
Max. Torque
(EEC)
142 N*m @ 2800 to 4400 rpm*1
142 N*m @ 4000 rpm*2
Valve Timing
Intake
Open
29°BTDC to 12°ATDC
Closed
61°ABDC to 102°ABDC
Exhaust
Open
31° BBDC
Closed
3° ATDC
Firing Order
1 - 3 - 4 - 2
Fuel
Unleaded Gasoline
Research Octane Number (RON)
95 or higher
Oil Grade
API grade SL "Energy-Conserving", SM "Energy-Conserving", SN "Energy-Conserving" or ILSAC
Emission Regulation
EURO V*1, BR-LEVZ*2
Engine Service Mass*3
(Reference)
90 kg (198 lb)

HINT:
*1: Models with EGR system
*2: Models without EGR system
*3: Weight shows the figure with oil and water fully filled.


W101584E05


W103106E02


MAIN FEATURES
  1. The 2ZR-FXE engine has achieved the following performance through the adoption of the items listed below.

    1. High performance and reliability

    2. Low noise and vibration

    3. Lightweight and compact design

    4. Good serviceability

    5. Clean emission and fuel economy

      Item
      (1)
      (2)
      (3)
      (4)
      (5)
      Engine Proper
      High-expansion Atkinson cycle is used.




      ○
      An aluminum cylinder block is used.


      ○


      An offset crankshaft is used.
      ○
      ○


      ○
      Spiny type liners are used.
      ○




      A taper squish shape is used for the top of the pistons.
      ○



      ○
      The skirt portion of the piston has a resin coating applied to reduce friction.
      ○
      ○


      ○
      Low-tension piston rings are used.
      ○



      ○
      Valve Mechanism
      A timing chain and chain tensioner are used.

      ○

      ○

      Hydraulic lash adjusters are used.

      ○

      ○

      Roller rocker arms are used.

      ○


      ○
      The VVT-i (Variable Valve Timing-intelligent) system is used.
      ○



      ○
      Intake and Exhaust System
      A plastic intake manifold is used.


      ○


      A linkless type throttle body is used.


      ○
      ○

      A DC motor type EGR valve is used.*
      ○



      ○
      A water-cooled type EGR cooler is used.*
      ○



      ○
      A stainless steel exhaust manifold is used.


      ○


      TWCs (Three-Way Catalytic converters) are used.




      ○
      A 2-way exhaust control system is used.
      ○
      ○



      Fuel System
      12-hole type fuel injectors are used.
      ○



      ○
      A fuel returnless system is used.


      ○
      ○

      Quick connectors are used to connect the fuel hoses and fuel pipes.



      ○

      Cooling System
      An engine water pump assembly is used.




      ○
      Ignition System
      A DIS (Direct Ignition System) is used.
      ○


      ○
      ○
      Long-reach type iridium-tipped spark plugs are used.
      ○


      ○
      ○
      Engine Control System
      The ETCS-i (Electronic Throttle Control System-intelligent) is used.
      ○



      ○
      An MRE (Magnetic Resistance Element) type cam position sensor is used.
      ○




      The flat type knock control sensor is used.
      ○




      HINT:
      *: Models with EGR system