Function
| Outline
|
Constant Speed Control
| The power management control ECU compares the actual vehicle speed with the set speed. If the vehicle speed is higher than the set speed, the power management control ECU calculates optimal motive forces for the engine and MG2, and decelerates by adjusting the respective motive forces. If the vehicle speed is lower than the set speed, the power management control ECU calculates optimal motive forces for the engine and MG2, and accelerates by adjusting the respective motive forces.
|
Set Control
| - When this system fulfils the following conditions, and the cruise control main switch is moved to the -SET side and released, the power management control ECU stores the vehicle speed and illuminates the cruise SET indicator light on the combination meter assembly and maintains the vehicle constantly at that speed.
- ON-OFF button on the cruise control main switch is pressed.
- The vehicle is running at an approximate speed of between 40 km/h (25 mph) and 200 km/h (125 mph).
|
Low Speed Limit Control
| The low speed limit is the lowest speed that cruise control can be set at and it is designed to be approximately 40 km/h (25 mph). The cruise control cannot be set below that speed. If the vehicle speed drops below that speed while running in the cruise control, the cruise control will be cancelled automatically. However the set speed is kept in memory.
|
COAST (-) Switch Control
| - When the cruise control main switch is held to the -SET side, the vehicle speed and the set vehicle speed change as follows:
- The vehicle will decelerate.
- The set vehicle speed will change to the speed that the vehicle is traveling at when the COAST switch (-SET side operation) is released.
|
Tap Down Control
| - When the cruise control main switch is moved momentarily (approximately 0.6 seconds or less) to the -SET side, the vehicle speed and the set vehicle speed change as follows:
- The vehicle will decelerate in increments of approximately 1.6 km/h (1 mph) each time the switch is moved.
- However, if the difference between the actual vehicle speed and the set vehicle speed is greater than 5 km/h (3 mph), the set vehicle speed will change to the speed at which the vehicle was traveling at when the switch was released.
|
ACC (+) Switch Control
| - When the cruise control main switch is held to the +RES side, the vehicle speed and the set vehicle speed change as follows:
- The vehicle will accelerate.
- The set vehicle speed will change to the speed at which the vehicle was being driven at the time the switch was released.
|
Tap Up Control
| - When the cruise control main switch is moved momentarily (approximately 0.6 seconds or less) to the +RES side, the vehicle speed and the set vehicle speed change as follows:
- The vehicle will accelerate in increments of approximately 1.6 km/h (1 mph) each time the switch is moved.
- However, if the difference between the actual vehicle speed and the set vehicle speed is greater than 5 km/h (3 mph), the set vehicle speed will not change.
|
RES Switch Control
| If the cruise control is canceled for any reason other than a malfunction (except cancellation by operating the ON-OFF button on the cruise control main switch) and the vehicle speed is more than the low speed limit, the vehicle can be returned to the speed which was before the cancellation of cruise operation by moving the cruise control main switch to the +RES side. The cruise control mode can be resumed even if the vehicle speed drops below the low speed limit, because the speed in the memory has not been cleared.
|
Manual Cancel Control
| - If any of the following signals are sent to the power management control ECU, the cruise control is cancelled accordingly.
- Stop light switch on signal (The brake pedal is depressed.)
- D position circuit in the shift lever position sensor off signal (The shift lever is moved from D to N or B.)
- CANCEL switch on signal (The cruise control main switch is moved to the CANCEL side.)
- Cruise control main switch (ON-OFF button) off signal
- VSC operation
|
Automatic Cancel Control
| - If the following condition occurs during cruise control operation, the speed that is set in the memory is cleared and the cruise control is cancelled.
- Stop light switch open or short circuit
- Furthermore, the cruise main indicator light will blink until the ON-OFF button on the cruise control main switch is used to turn the system off, and the operation of the cruise control will be disabled until the ON-OFF button is turned on again.
|
- If the following condition occurs during cruise control operation, the speed that is set in the memory is cleared and the cruise control is cancelled.
- Malfunction in the hybrid system
- Furthermore, the operation of the cruise control will be disabled until the ON-OFF button is turned on again.
|
- If any of the following conditions occur during cruise control operation, the speed that is set in the memory is cleared and the cruise control is cancelled.
- Stop light switch input signal is abnormal.
- Cancel circuit malfunction
- Brake control system malfunction
- Communication malfunction between the skid control ECU and power management control ECU
- Furthermore, the cruise main indicator light will blink until the ON-OFF button on the cruise control main switch is used to turn the system off, and the operation of the cruise control will be disabled until the power switch is turned off.
|
- If the following condition occurs during cruise control operation, the speed that is set in the memory is cleared and the cruise control is cancelled.
- Vehicle speed decreases by 16 km/h (10 mph) or more below the speed at which the cruise control was set.
|
- If the following condition occurs during cruise control operation, the cruise control is cancelled.
- Vehicle speed is below the low speed limit (approximately 40 km/h [25 mph]).
|