BODY STRUCTURE > DETAILS



FUNCTION


  1. Impact Absorbing Structure for Front Collisions

    1. The front side members utilize high strength steel sheet in a construction that absorbs and disperses energy in a frontal collision.

    2. The use of under members enables a construction that disperses load from the radiator supports.

    3. Door beltline reinforcements have been strengthened to optimize dispersal of collision energy to the rail, door beltline, and rocker panel.

    4. The use of a cross member in the dash panel enables a construction that disperses load from the front side members to the floor member and upper body.



    5. The use of members on the front floor at the sides of the tunnel enables a construction that achieves tunnel strength and dispersal of load from the front side members.


      Y101739E03


      Text in Illustration 
      *1
      Under Member
      *2
      Front Side Member
      *3
      Front Door Beltline Reinforcement
      *4
      Cross Member of the Dash Panel (Front Panel Member Sub-assembly)
      *5
      Member at the Side of the Tunnel
      -
      -
      V100135
      Path of Collision Energy
      -
      -



    6. An impact absorbing pad with sound absorbing performance is mounted from the lower surface of the dash panel to the floor front end to reduce damage to the legs in a collision.


      Y101741E01


      Text in Illustration 
      *1
      Foot Rest Area (No. 2 Dash Panel Insulator Pad)
      *2
      Accelerator Pedal Area (No. 1 Dash Panel Insulator Pad)
      *3
      Passenger Seat (No. 3 Dash Panel Insulator Pad)
      -
      -
      *a
      Front
      -
      -



  2. Impact Absorbing Structure for Side Collision

    1. Ultra high strength steel sheet* is used for the center pillar outer reinforcement, rocker panel inner, rocker panel outer reinforcement, roof center reinforcement, and center pillar hinge reinforcement to ensure high strength.

    2. Bulkheads are placed on both sides of the No. 1 and No. 2 floor cross members and center floor side crossmember to efficiently transmit impact load from the impact beam to the floor cross members.

    3. The use of a roof reinforcement enables a construction that transmits load to the opposite side of the vehicle in a collision.

    4. Optimal placement of the impact protect beam enables a construction that efficiently transmits load.



    5. The impact support box has been optimally placed on the front floor between the front driver's seat and front passenger's seat to ensure that load is transmitted from the center pillar to the seat pipe, impact support box, and seat pipe on the opposite side, thus helping secure sufficient survival space.

      HINT:
      *1: Ultra high strength steel sheet has approximately 1.3 times the strength of conventional high strength steel sheet.


      Y102587E01


      Text in Illustration 
      *1
      Impact Support Box
      *2
      Roof Reinforcement
      *3
      Impact Beam
      *4
      Floor Cross Member
      *5
      Center Pillar
      *6
      Center Console Box
      *7
      Front Seat Pipe
      *8
      Front Floor
      *9
      Front Seat Pipe (Collision side)
      *10
      Center Pillar Outer Reinforcement
      *11
      Hinge Reinforcement
      -
      -
      *a
      A-A Cross Section
      *b
      B-B Cross Section
      V100135
      Path of Collision Energy




  3. Impact Absorbing Structure for rear collision



    1. Straight rear side members are used to reduce body deformation in a rear collision, and the reinforcements in rear side members have been optimally located to ensure high strength.


      Y102564E01


      Text in Illustration 
      *1
      Side Member to Floor, Reinforcement Sub-assembly
      *2
      Rear Side Member
      V100135
      Path of Collision Energy
      -
      -



  4. Lessening Pedestrian Injury



    1. An energy absorber is provided at the front of the front bumper reinforcement to dampen the impact to the legs in the event of a collision with a pedestrian.


      Y101746E01


      Text in Illustration 
      *1
      Hood Panel
      *2
      Front Symbol Mark
      *3
      Front Bumper Cover
      *4
      Front Bumper Energy Absorber
      *5
      Front Bumper Reinforcement
      *6
      Lower Grille
      *7
      Front Bumper Lower Absorber
      *8
      Front Bumper Spoiler
      *a
      A-A Cross Section
      -
      -

    2. A longitudinal ribbed structure is adopted for the inner hood to cushion impact.



    3. The space between the hood panel and the hood lock striker has been formed into a crushable structure so that the hood sub-assembly can collapse easily during a collision.


      Y101734E01


      Text in Illustration 
      *1
      Hood Reinforcement
      *2
      Hood Lock Striker
      *a
      Longitudinal Ribbed Structure
      *b
      A-A Cross Section
      *c
      Space
      -
      -



    4. An impact absorbing bracket is used for the mounting portion of the front fender panel to absorb impact energy to the head of the pedestrian in a collision, thus dampening the impact to the head.


      Y101740E02


      Text in Illustration 
      *1
      Front Fender Panel (Front Fender Sub-assembly RH)
      *2
      Impact-absorbing Bracket (Front Apron to Cowl Side Member Plate RH)
      *3
      Impact-absorbing Bracket (Apron Fender Side Extension RH)
      -
      -



    5. The back of the hood and the cowl use an open section structure that collapses easily in an impact from the top, thus reducing the impact to and head injuries sustained by a pedestrian in an accident.


      Y101735E03


      Text in Illustration 
      *1
      Windshield Glass
      -
      -
      *a
      A-A Cross Section
      *b
      Open Section Structure (Rear Edge of Hood)
      *c
      Open Section Structure (Cowl)
      -
      -



  5. Aerodynamics

    1. Leveling off the surface where the front pillar meets the windshield and smoothing the shape around the doors and rocker were effective in reducing flow separation. For reducing flow separation, optimized the angle of the side surface of the front bumper is adopted.



    2. For controlling flow balance, the optimum rear spoiler shape and air-kick shape at rear combination light were studied considering the flow velocity and direction.


      Y101753E01


      Text in Illustration 
      *a
      Leveled off Front Pillar to Reduce Turbulence
      *b
      Reduced Flow Separation by Optimizing Angle of Side Surface of Front Bumper
      *c
      Smooth Flow along Doors and Rocker Surface
      *d
      Optimum Height, Length, and Angle of Rear Spoiler
      *e
      Air-kick Shape to Rear Combination Light
      *f
      Sharp Edge at the Side or Rear Bumper
      V100136
      Airflow
      -
      -

    3. Spats are fitted at the front of the front and rear tires to direct the air flow, and this reduces air turbulence into the wheel house, leading to ensured straight driving stability at high speeds.



    4. The height, angle, and shape of the engine under cover and the floor covers have been optimized, and the location and shape of the covers for chassis, fuel system, and exhaust parts have been optimized, resulting in smooth airflow underneath the floor.


      Y101742E03


      Text in Illustration 
      *1
      Front Spoiler
      *2
      Engine Under Cover
      *3
      Front Spats
      *4
      Engine Under Cover No.2
      *5
      Floor Cover
      *6
      Body Rocker Panel Moulding
      *7
      Fuel Tank Side Cover
      *8
      Rear Spats
      *9
      Rear Floor Cover
      *10
      Suspension Member Cover
      *11
      Rear Under Spoiler
      -
      -

    5. A groove has been added at the front of the fender liner, resulting in smooth flow of air. Steps have been added at the rear of the fender liner, and because these steps reduce airflow in the reverse direction, the flow of air into the wheel house has been reduced.



    6. The flat surfaces of the wheel cap and wheel have been optimized, resulting in smooth airflow around the wheel house.


      Y102565E01


      Text in Illustration 
      *1
      Fender Liner
      -
      -
      *a
      Flat Surface Around Wheel Cap Rim
      *b
      A-A Cross Section
      *c
      Bead
      *d
      Steps
      V100136
      Airflow
      -
      -



    7. The deflector is installed onto the radiator support to direct driving airflow into the radiator, thus leading to improvement in the ventilation performance of the vehicle front section.


      Y101744E03


      Text in Illustration 
      *1
      Radiator Support Opening Cover
      *2
      Radiator Side Deflector RH
      *3
      Radiator Side Deflector LH
      -
      -


CONSTRUCTION


  1. Light Weight and Highly Rigid Body

    1. A highly rigid yet lightweight vehicle body has been created by considerable use of mainly high strength steel sheet and Ultra high strength steel sheet* for body frames, thus ensuring a high level of impact safety, driving stability and quietness.



    2. Aluminum is used in the hood panel, back door panel, front bumper reinforcement, and rear bumper reinforcement, resulting in light weight.

      HINT:
      *: Ultra high strength sheet has approximately 1.3 times the strength of conventional high strength steel sheet.


      Y101749


      Text in Illustration (Upper Body: ) 
      V100144
      Ultra High Strength Steel Sheet
      V100145
      High Strength Steel Sheet
      V100155
      Aluminum
      -
      -

      Y101750


      Text in Illustration (Under Body: ) 
      V100144
      Ultra High Strength Steel Sheet
      V100145
      High Strength Steel Sheet
      V100155
      Aluminum
      -
      -



  2. Body Shell Construction



    1. A brace (front stabilizer bracket) is used on the lower side of the front suspension member to improve front suspension member fore-aft rigidity and ensure excellent driving stability.


      Y101754E03


      Text in Illustration 
      *1
      Brace (Front Stabilizer Bush Bracket)
      *2
      Front Suspension Member
      *a
      Front
      *b
      Lower View of Vehicle

    2. The front fender apron rear extension is used to connect the left and right front spring supports to the cowl top outer front panel, which is straight, improving lateral rigidity and ensuring front suspension input point rigidity and body rigidity.



    3. The cowl top inner to pillar brace bracket is used to connect the front spring support, cowl top outer front panel, and front body inner pillar, resulting in improved fore-aft rigidity.


      Y102562E02


      Text in Illustration 
      *1
      Cowl Top Inner to Pillar Brace Bracket
      *2
      Front Body Inner Pillar
      *3
      Front Spring Support Plate
      *4
      Front Spring Support
      *5
      Cowl Top Outer Panel
      *6
      Front Fender Apron Rear Extension
      *7
      Cowl Top Outer Front Panel
      -
      -

    4. The entire circumference from the rear header to the lower back panel uses an open structure, ensuring rigidity for the back door opening.

    5. Reinforcements (body lower back panel center reinforcement and body lower back No. 2 reinforcement RH/LH) are used to connect both rear sidemembers and side panels beneath the lower back panel, ensuring rigidity to counter twisting forces and delivering excellent driving stability.



    6. An inner gusset (quarter wheel house inner gusset) and outer reinforcement (roof side outer panel) are used for the wheelhouse construction, ensuring lateral rigidity at the rear absorber mounting portions, thus ensuring rigidity to counter twisting forces and achieving excellent driving stability.


      Y102561E01


      Text in Illustration 
      *1
      Roof Side Outer Panel
      *2
      Quarter Wheel House Inner Gusset
      *3
      Quarter Wheel House Inner Panel
      *4
      Body Lower Back Panel
      *5
      Body Lower Back No.2 Reinforcement LH
      *6
      Body Lower Back Panel Center Reinforcement
      *7
      Body Lower Back No.2 Reinforcement RH
      -
      -
      *a
      Rear View of Vehicle
      *b
      A-A Cross Section
      *c
      Open Section Structure
      *d
      B-B Cross Section
      *e
      C-C Cross Section
      *f
      D-D Cross Section



  3. Anti-corrosion Steel Sheet



    1. Anti-corrosion steel sheet is used as in the following illustration.


      Y102590


      Text in Illustration (Upper Body: ) 
      V100145
      Anti-corrosion Steel Sheet
      -
      -

      Y102591


      Text in Illustration (Under Body: ) 
      V100145
      Anti-corrosion Steel Sheet
      -
      -

  4. Wax and Sealer

    1. Wax is applied to front end of hood, edge of the door lower portion, fuel filler lid hinge to improve rust-resistant performance. Sealer is applied to hemmed portions of the front end of hood, front & back door panels and fuel filler lid.



  5. Under Coat



    1. Acrylic acid resin is applied to the under side of the body, inside the wheel housing and other parts that are susceptible to stone chipping damage, thus improving the rust-resistant performance of these areas.


      Y101751E04


      Text in Illustration 
      *a
      Under Floor
      *b
      Front Wheel House
      *c
      Rear Wheel House
      -
      -
      Y102599
      Edge Seal
      V100145
      Acrylic Acid Resin Coating Area
      V100144
      Acrylic Acid Resin Coating Area (Thick Coating)
      -
      -



  6. Anti-chipping Application

    1. To protect the paint from chipping, anti-chipping paint is applied to the rockers and the front end of the hood panel.



    2. A quarter panel protector and a rear door panel protector are applied to the quarter panel on the back of the rear door to protect the paint surface from icy snow or gravel and to achieve a high level of rust resistance.


      Y102566E03


      Text in Illustration 
      *1
      Soft Chipping Primer
      *2
      Plastic Rocker
      *3
      Rear Door Panel Protector
      *4
      Quarter Panel Protector
      *5
      Urethane Coating
      -
      -
      *a
      A-A Cross Section
      -
      -



  7. Low Vibration and Low Noise Body



    1. A dash panel insulator outer is provided. This reduces the amount of engine noise leaking into and out of the cabin.


      Y102567E02


      Text in Illustration 
      *1
      Dash Panel Insulator Outer
      -
      -



    2. A hood insulator is provided on the rear of the hood panel. This achieves excellent sound insulation performance.


      Y102568E02


      Text in Illustration 
      *1
      Hood Insulator
      -
      -



    3. The front (engine side) of the cowl top outer front panel uses a cowl top insulator sheet to reduce the amount of engine noise entering the vehicle cabin from the engine room.


      Y102569E03


      Text in Illustration 
      *1
      Cowl Top Outer Front Panel
      *2
      Windshield Glass
      *3
      Hood Panel
      *4
      Cowl Top Insulator Sheet
      *a
      A-A Cross Section
      -
      -



    4. Sound absorbing material (Thinsulate) is used in the front fender liner to reduce road noise.


      Y102570E02


      Text in Illustration 
      *1
      Front Fender Liner
      *2
      Thinsulate (Front Fender Seal)



    5. A front fender side panel protector is used to reduce the amount of noise transmitted from the area between the fender and front pillar to the vehicle cabin.


      Y102571E01


      Text in Illustration 
      *1
      Front Fender Side Panel Protector
      *2
      Fender
      *3
      Front Door
      *4
      Side Outer Panel
      *a
      A-A Cross Section
      -
      -
      V100135
      Noise
      -
      -



    6. A front fender upper protector is used on the engine room side of the fender side cover to reduce the amount of noise transmitted from the area between the fender and apron to the vehicle cabin.


      Y102572E01


      Text in Illustration 
      *1
      Front Fender
      *2
      Fender Side Cover
      *3
      Front Fender Upper Protector
      *4
      Apron
      *a
      A-A Cross Section
      *b
      Noise



    7. Foamed urethane sponge, foamed sealing material and sealing material are applied onto the roof panel and pillars to reduce wind and road noise.


      Y102573E03


      Text in Illustration 
      *a
      Models with Moonroof with Solar Panel only
      -
      -
      V100146
      Polyethylene Sealer
      V100145
      Expanded Form
      V100144
      Polyurethane Form
      -
      -



    8. The following body structures are used, in order to reduce panel vibration and body frame movement.

      Panel vibration reduction structure
      1. The front spring support and the cowl top outer front panel are connected
      2. The cross member of the dash panel is provided
      3. The tunnel reinforcement is connected to the floor
      4. The floor pan panel rigidity has been improved
      5. The floor pan bead layouts have been changed
      Body frame movement prevention structure
      1. A rocker inner bulkhead is provided
      2. A rocker inner rear and floor are rigidly connected
      3. A straight shape No. 1 cross member is used


      Y102574E03


      Text in Illustration 
      *1
      Cowl Top Outer Front Panel
      *2
      Cross Member of The Dash Panel
      *3
      Tunnel Reinforcement
      *4
      Bead
      *5
      Rocker Inner Bulkhead
      *6
      Rocker Inner Rear
      *7
      No.1 Crossmember
      -
      -



    9. Anti vibration material is applied to the floor in order to reduce noise in the cabin. As a replacement for the conventional asphalt-based vibration damping sheet, high rigidity spray type damping material is used, thus optimizing material coating thickness. This ensures high quality sound insulation and weight reduction. By applying it also to the dash panel vertical wall, noise from the engine room has been reduced.


      Y101752E03


      Text in Illustration 
      *1
      Dash Panel
      *2
      Floor
      V100145
      Spray Type Damping Material Application Area
      -
      -



    10. The following part shapes have been changed and the following structure is used for reducing wind noise.

      Hood rear edge shape change
      1. The rear edge of the hood is raised to control the wind flow to the wiper.
      2. An air flow routing plate has been provided to the fender parting section in order to smooth the wind flow.
      Flush surface structure usage
      1. The gap between the windshield glass and the roof has been made smaller to smooth the wind flow.
      Front pillar shape change
      1. The gap between the windshield and the front pillar has been optimized to reduce reverse wind flow.
      2. The gap between the frame design surface and the front fix wind moulding has been made smaller.


      Y102584E03


      Text in Illustration 
      *1
      Air Flow Routing Plate
      *2
      Hood Rear Edge
      *3
      Windshield Glass
      *4
      Roof Panel
      *5
      Frame Design Surface
      *6
      Front Window Fixed Moulding
      *a
      A-A Cross Section
      *b
      B-B Cross Section
      *c
      C-C Cross Section
      *d
      D-D Cross Section
      *e
      Gap
      -
      -
      V100136
      Frame Design Surface
      -
      -



  8. Parts with Low Repair Cost

    1. A front bumper reinforcement crush box (front side member bracket) absorbs impact energy to reduce damage to the body frame. The front bumper reinforcement is connected to the front sidemember using bolts to improve ease of repairs and replacement.



    2. A structure with the radiator support connected to the front sidemember using bolts is used to improve the ease of repairs, by reducing the damage to related parts (only the damaged parts need to be replaced).


      Y102585E01


      Text in Illustration 
      *1
      Radiator Support Sub-assembly
      *2
      Crash Box (Front Side Member Bracket Sub-assembly)
      *3
      Front Bumper Reinforcement Sub-assembly
      -
      -



    3. In case of a minor collision, the radiator support moves rearward together with the cooling unit, thus protecting the cooling unit and reducing damage.


      Y102576E03


      Text in Illustration 
      *a
      Barrier
      *b
      Barrier Insertion
      *c
      The Radiator Support Moves Rearward Together with the Cooling Unit
      *d
      Before Collision
      *e
      After Collision
      -
      -
      V100135
      Collision Energy Load Application Direction
      -
      -



    4. The crush box (rear bumper arm sub-assembly) is connected to the rear sidemember using bolts to improve the ease of repairs and replacements.


      Y102586E01


      Text in Illustration 
      *1
      Crash Box (Rear Bumper Arm Sub-assembly)
      *2
      Body Lower Back Panel Sub-assembly