NAVIGATION SYSTEM / MULTI INFORMATION SYSTEM > DETAILS



FUNCTION
  1. Navigation Screen

    1. The navigation computer calculates the present position and direction of travel, then determines a route and calculates the driving distance based on the following information sources:

      1. - Map data in the HDD (Models with HDD navigation system)
      2. - Map data in the extension module (Models with touch screen system)
      3. - Global Positioning System (GPS) satellites
      4. - Built-in gyro sensor
      5. - Vehicle speed signal
      6. - Reverse signal
      7. - Parking Brake signal
      8. - Radio Data System Traffic Message Channel (RDS-TMC and TPEG) Signal*1
      9. - Radio Data System Traffic Message Channel (RDS-TMC) Signal*2*3*4*5
      1. *1: Models for Europe with HDD navigation system
      2. *2: Models with touch screen system
      3. *3: Destination package for South Africa
      4. *4: Destination package for Taiwan
      5. *5: Destination package for Southeast Asia

    2. The functions of the navigation screen are listed below.

      Item
      Function
      System
      Touch Screen System
      HDD Navigation System
      Map Display
      Linear Touch Scroll
      Enables smooth scrolling by connecting the touch points on the screen.
      -
      X
      Map Color Change
      Depending on the position of the light control switch, the screen changes to day mode or night mode.
      X
      X
      Taillight-interlocked Map Color Change
      Changes the color of the map screen that is displayed when the taillights are turned on.
      X
      X
      North Up / Heading Up
      1. If North Up is selected, regardless of the direction of vehicle travel, north is always up.
      2. If Heading Up is selected, the direction of vehicle travel is always up.
      X
      X
      3D Display
      Displays a 3-dimensional (3D) view of the map.
      X
      X
      Multi-step Scale Display
      Changes the map scale in 14 steps.
      X
      X
      Direct Scale Change
      Directly selects and displays the map scale.
      -
      X
      Street Name Indication on Scrolled Map
      Displays the street name and city name even when the map screen is being scrolled.
      X
      X
      Stepless Scale Display
      Changes the scale of the map from the basic 14 steps to an even finer range of scales.
      -
      X
      Road Number Sign Board Display
      Displays the road number on the map.
      X
      X
      Point of Interest Display
      Displays selected types of points of interest as marks on the map.
      X
      X
      Home Screen Display
      Displays different modes on a screen that is split into 3 views.
      -
      X*1
      Split-view Display
      Displays different modes on a screen that is split into 2 views.
      -
      X*2*3*4*5
      Compass Mode Screen
      Displays the direction of travel and detailed data of the present location.
      -
      X*1*2*3*5
      Route Guidance Demonstration
      Demonstrates the route guidance to the destination.
      X
      X
      Route Trace
      It is possible to store up to the last 124 miles (200 km) of a traveled route and retrace the route on the display.
      -
      X
      Vehicle Icon
      Appears on the 3D display. The color can be changed among blue, red, yellow, green and purple.
      X
      -
      RDS-TMC and TPEG Service Information Display
      Displays the traffic icons, arrows and indicators when RDS-TMC or TPEG service information is being received.
      -
      X*1
      RDS-TMC Display
      Displays RDS-TMC icons, arrows and indicators when RDS-TMC service is being received.
      X
      X*2*3*4*5
      Destination Search
      Preset Destination Memory Search
      Sets a pre-registered point as a destination point while driving.
      -
      X
      Address Search
      A destination can be set by entering a country, and town name / code name, and street / intersection name.
      X
      -
      A destination can be set in 2 ways:
      1. Information can be entered in the order of: street name, town and house number.
      2. Information can be entered in the order of: town, street name and house number.
      -
      X*1*3
      A destination can be set in 2 ways:
      1. Information can be entered in the order of: street name, city and house number.
      2. Information can be entered in the order of: city, street name and house number.
      -
      X*2*5
      Information can be entered in the order of: province, city and street name.
      -
      X*4
      Point of Interest Search
      A destination can be set in 2 ways:
      1. The name of a POI can be entered and then searched for after selecting a search area. Search areas include defined areas (such as a user selected country, state and city), near the current position, near the main destination, or along the current route)
      2. A POI category can be selected and searched for near the current position, in a defined area (such as a user selected country, state and city), near the main destination, or along the current route.
      X
      X*4
      Hybrid Point of Interest Search
      Narrows the search by names of the point of interest, category and areas.
      -
      X*1*2*3*5
      Online Search
      Allows use of an internet search engine to set a destination using the most up to date information.
      X
      X*1
      Previous Destination Search
      Stores the coordinates, names, and date of up to 100 locations that have been set as destinations in the past.
      X
      X
      Memory Point Search
      Sets a destination from the registered memory point.
      -
      X*1*2*3*4
      My Place Search
      Sets a destination from the registered my place.
      -
      X*5
      Intersection Search
      By specifying 2 streets, the point at which they intersect is set as the destination point.
      -
      X*1*2*3*5
      Motorway Entrance or Exit Search
      Searches for the destination by the name of the street that connects to a motorway entrance or exit.
      -
      X*1*2*3
      Highway Entrance or Exit Search
      Searches for the destination by the name of the street that connects to a highway entrance or exit.
      -
      X*4
      Map Search
      A destination can be set by scrolling the cursor on the map.
      X
      X
      Coordinate Search
      A destination can be input by entering its coordinates.
      X
      X
      Voice-recognition Search
      A destination can be set up by voice command input.
      X
      X*1*2*3
      Phone Number Search
      A destination can be input by entering its phone number.
      -
      X*1*3*4*5
      Route Search
      Multiple Destination Setting
      Sets multiple destinations. It can also rearrange the sequence of the destinations.
      X
      X
      Multiple Route Search
      Searches for multiple routes.
      X
      X
      Search Condition Designation
      Searches for the quick 1, quick 2, and short routes.
      -
      X*1*2*3*5
      Searches for the recommended route, the shortest route, a route that prioritizes the use of highways, a route that prioritizes the use of general roads, and the other route.
      -
      X*4
      Searches for the fast, short, and ecological routes.
      X
      -
      Detour Search
      Changes the route to detour around a section of the route.
      X
      X
      Regulated Road Consideration
      Performs searches which consider regulated roads.
      X
      X
      Avoidance Area
      Searches for a route that avoids a designated area.
      -
      X
      Adjacent Road Search
      Searches for a route adjacent to the current road.
      -
      X*2
      Avoid Traffic Search
      Automatically changes to another route to avoid heavy congestion.
      -
      X*1*4*5
      Manually changes to another route to avoid heavy congestion.
      X
      X*2*3
      Guidance
      Voice Guidance
      Provides voice guidance about the distance and the direction of travel to a destination point based on road conditions and vehicle speed.
      X
      X
      Next Turn Guidance
      Provides guidance about the distance to the next turn and indicates the direction of the turn using an arrow.
      X
      X
      Motorway Mode Display
      Displays the distance to the next junction and exit, or POIs in the vicinity of the motorway exit.
      -
      X*1*2*3
      Highway Mode Display
      Displays the distance to the next junction and exit, or POIs in the vicinity of the highway exit.
      -
      X*4
      Motorway Direction of Travel Display
      Displays the direction of travel to take on the motorway.
      -
      X*1*2*3
      Highway Direction of Travel Display
      Displays the direction of travel to take on the highway.
      -
      X*4
      Intersection Zoom-in Display
      Zooms in the image when approaching an intersection.
      -
      X
      Turn List Display
      Displays a turn list on the right side of the 2-screen display.
      -
      X
      Arrow (Turn-by-Turn) Display
      Displays the direction of the next turn and the distance to the turn on the right side of the 2-screen display.
      -
      X
      Distance-to-destination Display
      Displays the distance from the present location to the destination.
      X
      X
      Estimated Arrival Time Display
      Displays estimated arrival time.
      X
      X
      Others
      Voice Recognition
      Recognizes pre-programmed system commands spoken to operate the navigation system.
      X
      X*1*2*3

      1. X: Available
      2. -: Not available
      3. *1: Models for Europe
      4. *2: Models for Australia
      5. *3: Destination package for South Africa
      6. *4: Destination package for Taiwan
      7. *5: Destination package for Southeast Asia



  2. Information Screen (Models with Touch Screen System)

    1. Information about fuel consumption per minute or per trip can be displayed on the vehicle information screen display.



    2. The fuel consumption screen is displayed as illustrated below. This screen has the display functions listed below.


      Y113253E01


      Item
      Outline
      (1)
      Clear Switch
      Clears all past information.
      (2)
      Average Per Minute Fuel Consumption
      1. Displays the value that has been calculated by the combination meter assembly, which is based on the driven distance and the volume of fuel consumed (fuel injection signal), provided that the power switch is on (IG).
      2. Displays the average fuel consumption for the last minute, or since clear was last selected.
      (3)
      Recovered Energy
      1. Indicates the recovered energy for 1 minute with "E" symbols.
      2. The recovered energy status is calculated by the power management control ECU.
      (4)
      Energy Switch
      Displays the energy monitor.
      (5)
      Cruising Range
      Displays the approximate drivable distance.
      (6)
      Energy Monitor
      Indicates the energy transmission direction, making it possible to confirm the current drive method (engine, motor or both), the power generation status by the engine and status of regenerative energy use.
      1. The State Of Charge (SOC) of the battery can be checked on the meter. The meter shows the SOC in 8-levels.
      2. Displays the energy monitor status that has been calculated by the power management control ECU.
      (7)
      Consumption Switch
      Changes to the fuel consumption screen.



  3. Information Screen (Models with HDD Navigation System)

    1. The functions of the information screen display are listed below.

      Item
      Outline
      Fuel Consumption*1
      Information about fuel consumption per minute or per trip can be displayed.
      Traffic Information
      By receiving the RDS-TMC and TPEG service, a list of the current traffic incidents is displayed along with information on the incident's distance and position relative to the vehicle.*2
      By receiving the RDS-TMC service, a list of the current traffic incidents is displayed along with information on the incident's distance and position relative to the vehicle.*3
      Traffic Incidents*2
      By receiving the TPEG service, the traffic prediction information around the current vehicle position or map display cursor position can be displayed.
      Parking information*2
      By receiving the TPEG service, the location, fee and vacancy status of the parking lots can be displayed.
      Information provider's logo*2
      Displayed when receiving traffic information, traffic prediction information or parking lots information.

      1. *1: Except models for Europe
      2. *2: Models for Europe
      3. *3: Destination package for Taiwan



    2. The fuel consumption screen is displayed as illustrated below. This screen has the display functions listed below.


      Y113254E01


      Item
      Outline
      (1)
      Clear Switch
      Clears all past information.
      (2)
      Average Per Minute Fuel Consumption
      1. Displays the value that has been calculated by the combination meter assembly, which is based on the driven distance and the volume of fuel consumed (fuel injection signal), provided that the power switch is on (IG).
      2. Displays the average fuel consumption for the last minute, or since clear was last selected.
      (3)
      Recovered Energy
      1. Indicates the recovered energy for 1 minute with "E" symbols.
      2. The recovered energy status is calculated by the power management control ECU.
      (4)
      Energy Switch
      Displays the energy monitor.
      (5)
      Cruising Range
      Displays the approximate drivable distance.
      (6)
      Energy Monitor
      Indicates the energy transmission direction, making it possible to confirm the current drive method (engine, motor or both), the power generation status by the engine and status of regenerative energy use.
      1. The State Of Charge (SOC) of the battery can be checked on the meter. The meter shows the SOC in 8-levels.
      2. Displays the energy monitor status that has been calculated by the power management control ECU.
      (7)
      Fuel Consumption Switch
      Changes to the fuel consumption screen.

  4. Setup Screen (Models with Touch Screen System)

    1. The settings for the functions of the multi-display are available from the setup screen.

      Item
      Function
      Display Settings
      1. Map Menu and Camera screen adjustment
      2. Depending on the position of the headlight switch, the screen changes to day or night mode.
      General Settings
      1. The language can be selected.
      2. The beep sound can be turned off.
      3. Automatic text scrolling can be turned off.
      4. Registered information (personal data) can be cleared.
      5. Distance unit can be changed.
      6. The voice guidance volume can be adjusted or switched off.
      7. Phone voice volume can be adjusted.
      8. Ring volume can be adjusted.
      9. Voice Dialog volume can be adjusted.
      10. Data can be stored on a USB memory device.
      11. Data can be copied from a USB memory device.
      12. Time zones and the on/off settings of daylight saving time can be changed.
      Bluetooth Settings
      1. The connection to a Bluetooth device can be turned on or off.
      2. Connectable Bluetooth devices can be searched for.
      3. The names of the Bluetooth devices that are currently connected or that are in the connection history can be displayed in a list. Additionally, availability information for each Bluetooth device is displayed.
      4. PIN codes used for Bluetooth connection certification can be set.
      5. A profile for connecting to the internet can be set.
      Phone Settings
      1. The ring tone can be changed or turned off.
      2. Message reception notification can be turned on or off.
      3. E-mail reception notification can be turned on or off.
      4. Phone book data stored on a cellular phone can be transferred manually.
      Audio Settings
      1. Sound quality can be adjusted.
      2. Radio setting can be changed:
        1. Automatically seek an FM station that regularly broadcasts traffic information and the station broadcasts
        2. An FM station providing good reception is automatically selected if current reception worsens.
        3. Switching over to a broadcasting station within the same local program network.
      Vehicle Settings
      Customizable vehicle settings can be changed.

  5. Setup Screen (Models with HDD Navigation System)

    1. The settings for the functions of the multi-display are available from the setup screen.

      Item
      Function
      Display Settings
      1. Map Menu and Camera screen adjustment
      2. Depending on the position of the headlight switch, the screen changes to day or night mode.
      General Settings
      1. Time zones and the on/off setting of daylight saving time can be changed.*1*2*3*4
      2. The language can be selected.*1*4
      3. The voice recognition language can be selected.*1
      4. The home screen display can be changed.*1
      5. The beep sound can be turned off.
      6. The color theme of the screen can be changed.*5
      7. Automatic return from the audio screen to the map screen after audio operation can be changed.
      8. The color of the screen buttons can be changed.*1*2*3*4
      9. Distance unit can be changed.*1
      10. Registered information (personal data) can be cleared.
      11. Navigation system program can be updated.*1
      Voice Settings
      1. The voice guidance volume can be adjusted or switched off.
      2. Automatic volume settings for voice guidance while driving at high speeds can be set.*5
      3. Voice recognition talkback can be set.*1*2*3
      4. Voice guidance while using the audio system can be set.
      5. Voice guidance during route guidance can be set.*1*2*3*4
      Navigation Settings
      The Navigation Settings can be used to:
      1. Set detailed online search settings such as:*1
        1. Synchronized settings of the online search portal site and navigation system
        2. Pop-up message display during online search
        3. Automatic accumulated data downloading settings from the portal site
        4. Roaming pop-up message settings
        5. Memorization settings of the user name and password used when connecting to the portal site
        6. Search engine settings of the online search
        7. Deletion of the online search history
        8. Change of the user name and password used when connecting to the portal site
        9. Deletion of the user name and password used when connecting to the portal site
      2. Perform memory point related operations such as:*5
        1. Sets home
        2. Sets preset destinations
        3. Sets memory point
        4. Sets area to avoid
        5. Data can be stored on a USB memory device.
        6. Data can be copied from a USB memory device.
      3. Set detailed navigation settings such as:*5
        1. Visual city map display
        2. Map color (day mode or night mode)
        3. Character size on the map
        4. Notification display of a point where 2 roads meet
        5. Scale switching message display
        6. Travel time to the destination display the route guidance screen
        7. Traffic information display on the navigation system's route
        8. Animated screen display
        9. 6 icons to be displayed while driving
        10. 3 different setting memorization for different users
        11. Manual adjustment of the current vehicle position mark
      4. Set detailed traffic information settings such as:*5
        1. Voice guidance for traffic information
        2. Traffic information icon display
        3. Avoid traffic events function
        4. Traffic station selection
        5. Station display that is currently received or has been selected
      5. Delete previous destinations*5
      6. Show map data information*5
      7. Set detailed navigation settings such as average cruising speed*1*2*3*4
      8. Buttons displayed on the map screen when "OFF" is selected*2*3*4
      9. Set detailed navigation settings such as displayed POI icon categories*1*2*3*4
      10. Set detailed navigation settings such as display of 3D landmarks*1*3*4
      11. Display cautionary messages when the route includes traffic restrictions or seasonally restricted roads.*3*4
      12. Displaying the speed limit of the road currently being used can be set*1
      13. The function that magnifies the map scale as the vehicle approaches a guidance point can be set*1
      14. Set the cautionary message display shown when a regulated street is included in the route
      15. Set the display of pop-up information*1*2*3
      16. Set the railroad crossing advisory*2
      17. Set the high accident location guidance*2
      18. Manual adjustment of the current vehicle position mark*1*2*3*4
      Vehicle Settings
      1. Settings can be changed for the following maintenance items:
        1. Reminder
        2. Engine oil
        3. Oil filter
        4. Rotation
        5. Tires
        6. Battery
        7. Brake pad
        8. Wipers
        9. Coolant
        10. Brake oil
        11. Trans. fluid
        12. Service
        13. Air filter
        14. Personal
        15. Set dealer
      2. Customizable vehicle settings can be changed.
      Telephone Settings
      1. Phone sound settings can be changed:
        1. Call Volume
        2. Ring Tone Volume
        3. Ring Tone
      2. Phonebook settings can be changed:
        1. Manage Contacts
        2. Manage Speed Dials
        3. Delete Call History
        4. Manage Voice Tags*5
      3. Message function settings can be changed*1:
        1. Message forwarding from cellular phones
        2. New message notification display
        3. New message voice notification
        4. Adjust the new message notification volume
        5. Select a new message voice notification tone
        6. Automatic message read out
        7. Adjust the message read out volume
        8. Cellular phone's read and unread status update
        9. Edit "Quick Reply messages"
      4. Phone display settings can be changed:
        1. Change the incoming call display
        2. Display of the automatic phonebook transfer completion message (For PBAP compatible models)
        3. Display of the automatic call history transfer completion message (For PBAP compatible models)
        4. Display of images during calls (For PBAP compatible models)
        5. Orientation of images displayed during calls (For PBAP compatible models)
      Bluetooth Settings
      1. Bluetooth device registration settings can be changed:
        1. Register a Bluetooth device
        2. Delete the Bluetooth device
        3. Edit the Bluetooth device
      2. Bluetooth devices can be selected
      3. Bluetooth device settings can be changed:
        1. Automatic connection to a Bluetooth device
        2. Changed to a desired Bluetooth device name
        3. Edited the Bluetooth device passcode
        4. Display Bluetooth device connection status
        5. Bluetooth DUN profile settings*1*2
      Audio Settings
      1. Sound quality can be adjusted.*1*2*3
      2. Radio setting can be changed:
        1. Automatically seek an FM station that regularly broadcasts traffic information and the station broadcasts
        2. An FM station providing good reception is automatically selected if current reception worsens.
        3. Switching over to a broadcasting station within the same local program network.
        4. A station providing good reception is automatically selected if current reception worsens.*2
      3. Display cover art when a song stored in an iPod is being played.
      Traffic and Parking Settings*1
      1. The voice guidance for traffic information can be switched off.
      2. Traffic information icons can be displayed on the map.
      3. Detour route function can be selected.
      4. When searching for a route, a detoured route search that avoids traffic jams and so forth can be set.
      5. When searching for a route, a detoured route search that avoids predicted traffic jams and so forth can be set.
      6. The stations can be selected.
      7. Traffic information can be set to be received automatically, or to receive RDS-TMC traffic information only.
      8. Parking icons can be displayed on the map.
      Traffic Information Settings*2*3*4
      1. The voice guidance for traffic information can be switched off.
      2. Traffic information icon display can be set.
      3. Detour route function can be selected.
      4. The stations can be selected.

      1. *1: Models for Europe
      2. *2: Models for Australia
      3. *3: Destination package for South Africa
      4. *4: Destination package for Southeast Asia
      5. *5: Destination package for Taiwan


DIAGNOSIS
  1. For details on the procedure required to enter the Service Menu screen, refer to the Repair Manual.