FRONT SHOCK ABSORBER > INSTALLATION |
| 1. INSTALL FRONT COIL SPRING LOWER INSULATOR |
![]() |
Install the front coil spring lower insulator to the front shock absorber assembly.
| *1 | Positioning Pin |
| *2 | Depression |
| 2. INSTALL FRONT SPRING BUMPER |
![]() |
Install the front spring bumper to the front shock absorber assembly.
| 3. INSTALL FRONT COIL SPRING |
![]() |
Attach SST to the front coil spring and secure it in a vise.
![]() |
Attach the arm of SST to the diameter of the front coil spring.
Using SST, compress the front coil spring.
![]() |
Install the front coil spring to the front shock absorber assembly.
| *1 | Paint Mark |
| 4. INSTALL FRONT COIL SPRING UPPER INSULATOR |
| 5. INSTALL FRONT COIL SPRING UPPER SEAT |
| 6. INSTALL STRUT MOUNTING BEARING |
![]() |
Install the strut mounting bearing.
| *1 | Upper Side |
| *2 | Lower Side |
| 7. INSTALL FRONT SUSPENSION SUPPORT SUB-ASSEMBLY |
Install the front suspension support sub-assembly to the front shock absorber assembly.
| 8. TEMPORARILY TIGHTEN FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT |
![]() |
Install the collar to the front shock absorber assembly.
![]() |
Temporarily tighten a new front support to front shock absorber nut.
Remove SST from the front coil spring.
| 9. INSTALL FRONT SUSPENSION SUPPORT PLATE (w/o Rubber Foam) |
![]() |
Install the front suspension support plate to the front shock absorber with coil spring.
![]() |
| *1 | Rubber Foam |
| 10. INSTALL FRONT SHOCK ABSORBER WITH COIL SPRING |
![]() |
Install the front shock absorber with coil spring (upper side) with the 3 nuts.
![]() |
Install the front shock absorber with coil spring (lower side) to the steering knuckle with the 2 bolts and 2 nuts.
| 11. FULLY TIGHTEN FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT |
![]() |
Fully tighten the front support to front shock absorber nut.
| 12. INSTALL FRONT SUSPENSION SUPPORT DUST COVER |
![]() |
Install the front suspension support dust cover.
| 13. INSTALL FRONT SPEED SENSOR |
![]() |
Install the front speed sensor and front flexible hose to the front shock absorber with the bolt and clamp.
| 14. INSTALL FRONT STABILIZER LINK ASSEMBLY |
![]() |
Install the front stabilizer link assembly to the front shock absorber with coil spring with the nut.
| 15. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD) |
![]() |
Install the outer cowl top panel sub-assembly with the 9 bolts.
![]() |
Bend the water guard plate RH and engage the claw.
![]() |
Bend the No. 1 heater air duct splash shield seal and engage the claw.
![]() |
Engage the clamp to install the wire harness.
| 16. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD) |
![]() |
Install the outer cowl top panel with the 9 bolts.
![]() |
Bend the water guard plate RH and engage the claw.
![]() |
Bend the No. 1 heater air duct splash shield seal and engage the claw.
![]() |
Engage the clamp*2 of the wire harness.
Engage the clamp*1 and connect the connector (w/ Windshield Deicer).
![]() |
Engage the clamp of the wire harness.
| 17. INSTALL COWL BODY MOUNTING REINFORCEMENT LH (for LHD) |
![]() |
Install the cowl body mounting reinforcement LH with the 3 bolts.
| 18. INSTALL COWL BODY MOUNTING REINFORCEMENT LH (for RHD) |
![]() |
Install the cowl body mounting reinforcement LH with the 3 bolts.
| 19. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY |
| 20. INSTALL FRONT WHEEL |
| 21. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT |