Home › Suspension › FRONT SUSPENSION › FRONT SHOCK ABSORBER

FRONT SHOCK ABSORBER > REMOVAL

for Preparation Click here


HINT:
  1. Use the same procedure for the LH side and RH side.
  2. The procedure listed below is for the LH side.



1. REMOVE FRONT WHEEL


2. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

HINT:
Refer to the procedure up to Remove Windshield Wiper Motor and Link Assembly .



3. REMOVE COWL BODY MOUNTING REINFORCEMENT LH (for LHD)


    C209143
  1. Remove the 3 bolts and cowl body mounting reinforcement LH.



4. REMOVE COWL BODY MOUNTING REINFORCEMENT LH (for RHD)


    C205554
  1. Remove the 3 bolts and cowl body mounting reinforcement LH.



5. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)


    C205696
  1. Disengage the clamp and separate the wire harness.



    C209148
  1. Disengage the claw and bend the No. 1 heater air duct splash shield seal.



    C209146
  1. Disengage the claw and bend the water guard plate RH.



    C209144
  1. Remove the 9 bolts and outer cowl top panel sub-assembly.



6. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)


    C205556
  1. Disengage the clamp and separate the wire harness from the outer cowl top panel sub-assembly.



    C205555E01
  1. Disengage the clamp*1 and disconnect the connector (w/ Windshield Deicer).

  1. Disengage the clamp*2 and separate the wire harness from the outer cowl top panel sub-assembly.



    C205558
  1. Disengage the claw and bend the No. 1 heater air duct splash shield seal.



    C205560
  1. Disengage the claw and bend the water guard plate RH.



    C205557
  1. Remove the 9 bolts and outer cowl top panel sub-assembly.



7. SEPARATE FRONT STABILIZER LINK ASSEMBLY


    C205585
  1. Remove the nut and separate the stabilizer link assembly from the front shock absorber with coil spring.

    HINT:
    If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud bolt.



8. SEPARATE FRONT SPEED SENSOR


    C208843
  1. Remove the bolt and clamp, and separate the front speed sensor and front flexible hose from the front shock absorber with coil spring.

    NOTICE:
    Be sure to separate the front speed sensor from the front shock absorber with coil spring completely.



9. REMOVE FRONT SUSPENSION SUPPORT DUST COVER


    C205588
  1. Remove the front suspension support dust cover.



10. REMOVE FRONT SHOCK ABSORBER WITH COIL SPRING


    C205589
  1. Loosen the front support to front shock absorber nut of the front shock absorber.

    NOTICE:
    1. Do not remove the front support to front shock absorber nut.
    2. Loosen the nut only when the front shock absorber with coil spring needs to be disassembled.



    C207008E01
  1. Support the front axle using a jack and wooden block.
    Text in Illustration 
    *1
    Wooden Block



    C205584
  1. Remove the 2 bolts and 2 nuts, and separate the front shock absorber with coil spring (lower side) from the steering knuckle.



    C205591
  1. Remove the 3 nuts and front shock absorber with coil spring.

    NOTICE:
    Make sure that the front speed sensor is completely separated from the front shock absorber with coil spring.



11. REMOVE FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT


    C265530E01
  1. Secure SST in a vise.

    SST
    09727-30021   (09727-00010, 09727-00021, 09727-00031)



    C263591
  1. Attach the arm of SST to the diameter of the front coil spring.

    CAUTION:
    1. Make sure that the front coil spring is installed so that the distance between the upper and lower hooks of SST is at the maximum.
    2. Make sure that the claws of the hooks are securely attached.

  1. Using SST, compress the front coil spring.

    CAUTION:
    1. If the front coil spring bends during the compression, immediately stop the compression and reinstall SST.
    2. Do not compress the spring until the coil springs contact each other.
    3. Do not use an impact wrench. It will damage SST.



    C265531
  1. Confirm that the front coil spring becomes free and remove the front support to front shock absorber nut.

    CAUTION:
    Do not remove the front support to front shock absorber nut when the front coil spring is not free.

  1. Remove the collar.



12. REMOVE FRONT SUSPENSION SUPPORT SUB-ASSEMBLY


13. REMOVE STRUT MOUNTING BEARING


14. REMOVE FRONT COIL SPRING UPPER SEAT


15. REMOVE FRONT COIL SPRING UPPER INSULATOR


16. REMOVE FRONT COIL SPRING


17. REMOVE FRONT SPRING BUMPER


18. REMOVE FRONT COIL SPRING LOWER INSULATOR


19. REMOVE FRONT SHOCK ABSORBER ASSEMBLY