Home › Brake › BRAKE (REAR) › REAR BRAKE FLEXIBLE HOSE

REAR BRAKE FLEXIBLE HOSE > INSTALLATION

for Preparation Click here


NOTICE:
  1. Because the left and right rear flexible hoses are not interchangeable, verify the part number when installing the flexible hoses.
  2. If the hoses are to be reused, connect them after checking the identification marks placed when each hose was disconnected.

HINT:
  1. Use the same procedure for the LH side and RH side.
  2. The following procedure is for the LH side.



1. INSTALL REAR BRAKE TUBE FLEXIBLE HOSE (for LH Side)


  1. Install the rear brake tube flexible hose with the bolt and a new clip.


    C209157E01


    Text in Illustration 
    *1
    Identification Mark
    *2
    Inside of the Vehicle

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

    NOTICE:
    1. Install the clip as far as it will go.
    2. When installing the rear brake tube flexible hose, face the identification mark to the inside of the vehicle and minimize twisting of the hose.

  1. Using a union nut wrench, connect the 2 brake lines to the rear brake tube flexible hose.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    1. Do not bend or damage the brake line.
    2. Do not allow any foreign matter such as dirt and dust to enter the brake line from the connecting points.
    3. Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench (Click here).



2. INSTALL REAR BRAKE TUBE FLEXIBLE HOSE (for RH Side)


  1. Install the rear brake tube flexible hose with 2 new clips.


    C209158E01


    Text in Illustration 
    *1
    Identification Mark
    *2
    Inside of the Vehicle

    NOTICE:
    1. Install the clip as far as it will go.
    2. When installing the rear brake tube flexible hose, face the identification mark to the inside of the vehicle and minimize twisting of the hose.

  1. Using a union nut wrench, connect the 2 brake lines to the rear brake tube flexible hose.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    1. Do not bend or damage the brake line.
    2. Do not allow any foreign matter such as dirt and dust to enter the brake line from the connecting points.
    3. Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench (Click here).



3. INSTALL REAR FLEXIBLE HOSE


    C150136
  1. Connect the rear flexible hose to the rear disc brake cylinder assembly with a new union bolt and a new gasket.

    Torque:
    33 N*m{ 340 kgf*cm , 25 ft.*lbf }



    C150135
  1. Install a new clip.

    NOTICE:
    Install the clip as far as it will go.



    C205529
  1. Using a union nut wrench, connect the brake line to the rear flexible hose while holding the rear flexible hose with a wrench.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    1. Do not bend or damage the brake line.
    2. Do not allow any foreign matter such as dirt and dust to enter the brake line from the connecting points.
    3. Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench (Click here).



4. FILL RESERVOIR WITH BRAKE FLUID


5. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



6. INSTALL REAR NO. 3 FLOOR BOARD


    B227791
  1. Engage the 2 guides to install the rear No. 3 floor board.



7. INSTALL REAR DECK FLOOR BOX
  1. Install the rear deck floor box.



8. INSTALL REAR NO. 2 FLOOR BOARD


    B227788E01
  1. Engage the 3 guides <A>.

  1. Engage the 2 guides <B> and install the rear No. 2 floor board as shown in the illustration.



9. BLEED BRAKE LINE


  1. Remove the center cowl top ventilator cover.



      C205662
    1. Slide the hood to cowl top seal and disengage the claw.

    2. Disengage the 2 claws and 3 guides, and remove the center cowl top ventilator cover.



  1. Bleed brake line.



      C205665
    1. Remove the brake master cylinder reservoir filler cap assembly.

    2. Add brake fluid into the reservoir between MAX and MIN level on the brake fluid reservoir.

      Brake fluid:
      SAE J1703 or FMVSS No. 116 DOT3

    3. Connect the intelligent tester to the DLC3 and turn the power switch on (IG).

    4. Turn the intelligent tester on and enter the following menus: Chassis / ABS/VSC/TRC / Air Bleeding.

    5. Select the "Usual air bleeding" on the intelligent tester display, and bleed air from the brake fluid following the instructions on the intelligent tester.

    6. After air bleeding, tighten each bleeder plug.

      Torque:
      front bleeder plug:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf }
      rear bleeder plug:
      11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    7. Clear the DTCs (Click here).

    8. Turn the intelligent tester off and turn the power switch off.

  1. Inspect for brake fluid leaks.

  1. Install the brake master cylinder reservoir filler cap.



  1. Install the center cowl top ventilator cover.



      C205663
    1. Engage the 2 claws and 3 guides to install the center cowl top ventilator cover.

    2. Slide the hood to cowl top seal to engage the claw.



10. INSTALL REAR WHEEL

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }