Home › Vehicle Interior › SEAT › LUMBAR SUPPORT ADJUSTER ASSEMBLY

LUMBAR SUPPORT ADJUSTER ASSEMBLY > REMOVAL

for Preparation Click here



1. PRECAUTION (w/ Navigation System for HDD)

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).



2. REMOVE REAR NO. 2 FLOOR BOARD


    B227787E01
  1. Disengage the 2 guides <A> as shown in the illustration.

  1. Disengage the 3 guides <B> and remove the rear No. 2 floor board.



3. REMOVE REAR DECK FLOOR BOX
  1. Remove the rear deck floor box.



4. REMOVE REAR NO. 3 FLOOR BOARD


    B227791
  1. Disengage the 2 guides and remove the rear No. 3 floor board.



5. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



6. REMOVE FRONT SEAT HEADREST ASSEMBLY


    B229801
  1. Press the headrest support button and pull up the headrest as shown in the illustration to remove it.



7. REMOVE OUTER SEAT TRACK COVER


    B229805
  1. Lift up the seat track adjusting handle and move the seat to the foremost position.

  1. Disengage the 2 claws and remove the outer seat track cover.



8. REMOVE INNER SEAT TRACK COVER
  1. Disengage the claw.



    B229803
  1. Separate the guide and remove the inner seat track cover.



9. REMOVE FRONT SEAT ASSEMBLY


    B229807
  1. Remove the 2 bolts on the rear side of the seat.

  1. Lift up the seat track adjusting handle and move the seat to the rearmost position.



    B229808
  1. Remove the 2 bolts on the front side of the seat.

  1. Lift up the seat track adjusting handle and move the seat to the center position. Also, operate the reclining adjuster release handle and move the seatback to the upright position.

  1. Disconnect the connectors under the seat.

  1. Remove the seat.

    NOTICE:
    Be careful not to damage the vehicle body.



10. REMOVE RECLINING ADJUSTER RELEASE HANDLE


    B229811E01
  1. Using a screwdriver wrapped with protective tape, disengage the claw and remove the reclining adjuster release handle.
    Text in Illustration 
    *1
    Protective Tape



11. REMOVE VERTICAL ADJUSTING HANDLE


    B229813
  1. Remove the screw and vertical adjusting handle.



12. REMOVE FRONT SEAT CUSHION SHIELD ASSEMBLY


    B229815
  1. Remove the screw.

  1. Disengage the 2 claws and clip.



  1. w/ Lumbar Support:



      B229817
    1. Disconnect the connector.

    2. Disengage the 5 clamps and remove the front seat cushion shield assembly.



13. REMOVE FRONT SEAT INNER BELT ASSEMBLY
  1. Disconnect each connector.

  1. Disengage each clamp.



    B226477
  1. Remove the nut and front seat inner belt assembly.



14. REMOVE FRONT SEAT CUSHION INNER SHIELD


    B229819
  1. Disengage the 2 claws and remove the front seat cushion inner shield.



15. REMOVE FRONT SEAT CUSHION COVER WITH PAD


    B229821
  1. Remove the hook.



  1. w/ Lumbar Support:



      B229827
    1. Disconnect the connector.

    2. Disengage the 3 clamps.



    3. B229829
    4. Disengage the 4 clamps.



  1. w/ Seat Heater System:



      B229830
    1. Disconnect the connector.

    2. Unfasten the front seat cushion cover with pad as shown in the illustration.



    3. B229832
    4. Disengage the clamp.



    B229834
  1. Disengage the 4 hooks.



  1. for Passenger Side:



      B229823
    1. Disconnect the connector.

    2. Disengage the 3 clamps.



    3. B229825
    4. Disengage the guide and remove the belt warning occupant detection sensor.



    B230998
  1. Remove the 3 hog rings.



    B229842
  1. Disengage the 2 hooks as shown in the illustration.



  1. Disengage each hook and remove the front seat cushion cover with pad as shown in the illustration.


    B229838



16. REMOVE FRONT SEATBACK COVER WITH PAD


    B229850
  1. Remove the 3 hog rings.



    B229856
  1. Disengage the 4 claws and remove the 2 front seat headrest supports.



    B229854
  1. Turn back the separate type front seatback cover to remove the nut, and separate the bracket of the separate type front seatback cover RH.

  1. Remove the separate type front seatback cover with pad from the front seat frame assembly with adjuster.



17. REMOVE RECLINING ADJUSTER INSIDE COVER LH


    B229861
  1. Disengage the guide and remove the reclining adjuster inside cover LH.



18. REMOVE RECLINING ADJUSTER INSIDE COVER RH


    B229863
  1. Disengage the guide and remove the reclining adjuster inside cover RH.



19. REMOVE FRONT SEAT LOWER CUSHION SHIELD LH


    B229871
  1. Disengage the hook as shown in the illustration.



    B229873
  1. Remove the screw.

  1. Disengage the clip and remove the front seat lower cushion shield LH.



20. REMOVE FRONT SEAT LOWER CUSHION SHIELD RH


    B229865
  1. Disengage the hook as shown in the illustration.



    B229867
  1. Remove the screw.

  1. Disengage the clip and remove the front seat lower cushion shield RH.



21. REMOVE NO. 2 FRONT SEAT CUSHION PROTECTOR


    B229877
  1. Remove the screw.

  1. Disengage the 2 guides and remove the No. 2 front seat cushion protector.



22. REMOVE NO. 1 FRONT SEAT CUSHION PROTECTOR


    B229879
  1. Remove the screw.

  1. Disengage the 2 guides and remove the No. 1 front seat cushion protector.



23. REMOVE FRONT SEAT WIRE


    B229881
  1. Disconnect the connector.

  1. Disengage the 2 clamps and remove the front seat wire.



24. REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY


    B229884
  1. Remove the 4 bolts and separate type front seatback assembly.