LUMBAR SUPPORT ADJUSTER ASSEMBLY > REMOVAL |
| 1. PRECAUTION (w/ Navigation System for HDD) |
| 2. REMOVE REAR NO. 2 FLOOR BOARD |
![]() |
Disengage the 2 guides <A> as shown in the illustration.
Disengage the 3 guides <B> and remove the rear No. 2 floor board.
| 3. REMOVE REAR DECK FLOOR BOX |
Remove the rear deck floor box.
| 4. REMOVE REAR NO. 3 FLOOR BOARD |
![]() |
Disengage the 2 guides and remove the rear No. 3 floor board.
| 5. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 6. REMOVE FRONT SEAT HEADREST ASSEMBLY |
![]() |
Press the headrest support button and pull up the headrest as shown in the illustration to remove it.
| 7. REMOVE OUTER SEAT TRACK COVER |
![]() |
Lift up the seat track adjusting handle and move the seat to the foremost position.
Disengage the 2 claws and remove the outer seat track cover.
| 8. REMOVE INNER SEAT TRACK COVER |
Disengage the claw.
![]() |
Separate the guide and remove the inner seat track cover.
| 9. REMOVE FRONT SEAT ASSEMBLY |
![]() |
Remove the 2 bolts on the rear side of the seat.
Lift up the seat track adjusting handle and move the seat to the rearmost position.
![]() |
Remove the 2 bolts on the front side of the seat.
Lift up the seat track adjusting handle and move the seat to the center position. Also, operate the reclining adjuster release handle and move the seatback to the upright position.
Disconnect the connectors under the seat.
Remove the seat.
| 10. REMOVE RECLINING ADJUSTER RELEASE HANDLE |
![]() |
Using a screwdriver wrapped with protective tape, disengage the claw and remove the reclining adjuster release handle.
| *1 | Protective Tape |
| 11. REMOVE VERTICAL ADJUSTING HANDLE |
![]() |
Remove the screw and vertical adjusting handle.
| 12. REMOVE FRONT SEAT CUSHION SHIELD ASSEMBLY |
![]() |
Remove the screw.
Disengage the 2 claws and clip.
w/ Lumbar Support:
![]() |
Disconnect the connector.
Disengage the 5 clamps and remove the front seat cushion shield assembly.
| 13. REMOVE FRONT SEAT INNER BELT ASSEMBLY |
Disconnect each connector.
Disengage each clamp.
![]() |
Remove the nut and front seat inner belt assembly.
| 14. REMOVE FRONT SEAT CUSHION INNER SHIELD |
![]() |
Disengage the 2 claws and remove the front seat cushion inner shield.
| 15. REMOVE FRONT SEAT CUSHION COVER WITH PAD |
![]() |
Remove the hook.
w/ Lumbar Support:
![]() |
Disconnect the connector.
Disengage the 3 clamps.
![]() |
Disengage the 4 clamps.
w/ Seat Heater System:
![]() |
Disconnect the connector.
Unfasten the front seat cushion cover with pad as shown in the illustration.
![]() |
Disengage the clamp.
![]() |
Disengage the 4 hooks.
for Passenger Side:
![]() |
Disconnect the connector.
Disengage the 3 clamps.
![]() |
Disengage the guide and remove the belt warning occupant detection sensor.
![]() |
Remove the 3 hog rings.
![]() |
Disengage the 2 hooks as shown in the illustration.
Disengage each hook and remove the front seat cushion cover with pad as shown in the illustration.

| 16. REMOVE FRONT SEATBACK COVER WITH PAD |
![]() |
Remove the 3 hog rings.
![]() |
Disengage the 4 claws and remove the 2 front seat headrest supports.
![]() |
Turn back the separate type front seatback cover to remove the nut, and separate the bracket of the separate type front seatback cover RH.
Remove the separate type front seatback cover with pad from the front seat frame assembly with adjuster.
| 17. REMOVE RECLINING ADJUSTER INSIDE COVER LH |
![]() |
Disengage the guide and remove the reclining adjuster inside cover LH.
| 18. REMOVE RECLINING ADJUSTER INSIDE COVER RH |
![]() |
Disengage the guide and remove the reclining adjuster inside cover RH.
| 19. REMOVE FRONT SEAT LOWER CUSHION SHIELD LH |
![]() |
Disengage the hook as shown in the illustration.
![]() |
Remove the screw.
Disengage the clip and remove the front seat lower cushion shield LH.
| 20. REMOVE FRONT SEAT LOWER CUSHION SHIELD RH |
![]() |
Disengage the hook as shown in the illustration.
![]() |
Remove the screw.
Disengage the clip and remove the front seat lower cushion shield RH.
| 21. REMOVE NO. 2 FRONT SEAT CUSHION PROTECTOR |
![]() |
Remove the screw.
Disengage the 2 guides and remove the No. 2 front seat cushion protector.
| 22. REMOVE NO. 1 FRONT SEAT CUSHION PROTECTOR |
![]() |
Remove the screw.
Disengage the 2 guides and remove the No. 1 front seat cushion protector.
| 23. REMOVE FRONT SEAT WIRE |
![]() |
Disconnect the connector.
Disengage the 2 clamps and remove the front seat wire.
| 24. REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY |
![]() |
Remove the 4 bolts and separate type front seatback assembly.